2007 Tundra GB Install
Content
TOYOTA
Preparation
TUNDRA
2007 -
TVIP V2
GLASS BREAKAGE SENSOR (GBS)
NOTE: Part number of this accessory may not be the same as the part number shown.
Part Number: 08586-OC890
Conflicts
Do not install into vehicles without Factory Alarm Systems.
Recommended Tools
Personal & Vehicle Protection Safety Glasses Safety Gloves Vehicle Protection Special Tools Striker Tool (PPO only) Installation Tools Phillips Head Screwdriver Flat Blade Screwdriver Nylon Panel Removal Tool Torque Wrench Clear Tape Socket Special Chemicals Cleaner Glass Cleaner Notes
Recommended Sequence of Application
Item # 1 2 Accessory TVIP/RES XM Radio Any TVIP or RES system *Mandatory
(Optional) Blankets, Parts Boxes Notes
CAD-E IADS P/N ALL 02016-01
Kit Contents
Item # 1 Quantity 1 Description GBS ECU w/bracket attached
Notes #2, screwdriver or tip 1/8” wide screwdriver e.g. Panel Pry Tool #1
Toyota SST # 00002-06001-01 36 in•bf (40.67 n•cm)
Hardware Bag Contents
Item # 1 2 3 4 5 6 7 8 9 Quantity 1 1 2 2 2 2 1 1 1 Description M6 Flange Nut GBS Microphone V2 Window Label w/ red tag V2 Window Label w/ red tag SPANISH V5 Window Label (discard) V5 Window Label SPANISH (discard) V2 Owner’s Guide V5 Owner’s Guide (discard) Warranty Card
10mm, Extension Notes VDC approved cleaner Household Windex
Legend
STOP: Damage to the vehicle may occur. Do not proceed until process has been complied with. OPERATOR SAFETY: Use caution to avoid risk of injury. CAUTION: A process that must be carefully observed in order to reduce the risk of damage to the accessory/vehicle and to ensure a quality installation. TOOLS & EQUIPMENT: Used in Figures calls out the specific tools and equipment recommended for this process. REVISION MARK: This mark highlights a change in installation with respect to previous issue.
Additional Items Required For Installation
Item # Quantity Description
Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this accessory should follow approved guidelines to ensure a quality installation These guidelines can be found in the "Accessory Installation Practices" document. This document covers such items as: • Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.). • Safety (eye protection, rechecking torque procedure, etc.). • Vehicle Disassembly/Reassembly (panel removal, part storage, etc.). • Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.). Please see your Toyota dealer for a copy of this document Issue: A 12/18/06 Page 1 of 14 pages
TOYOTA
Preparation A GBS ECU
GBS Microphone
TUNDRA
2007 -
TVIP V2
GLASS BREAKAGE SENSOR (GBS)
B
Issue: A
12/18/06
Page 2 of 14 pages
TOYOTA
Procedure
TUNDRA
2007 1. Vehicle Disassembly
TVIP V2
GLASS BREAKAGE SENSOR (GBS)
(a) Vehicles with Automatic Transmission should be placed in Park and have the Parking Brake set before disconnecting the Battery.
10mm Socket Negative Battery Cable
(b) Remove the Negative Battery Cable. (Fig. 1-1) (1) Protect the Fender before starting. (2) Note the Battery Cable Position, as it will be reinstalled in the same position.
DO NOT TOUCH THE POSITIVE BATTERY TERMINAL.
Fig. 1-1
Nylon Panel Removal Tool Step Cover
(c) Remove the Driver’s Step Cover. (Fig. 1-2) (1) Begin by protecting the Vehicle Interior with
Blankets.
Fig. 1-2
Cowl Cover
(d) Remove the Driver’s Cowl Cover. (Fig. 1-3) (1) Remove 1 Cowl Nut.
Cowl Nut
Fig. 1-3
Issue: A
12/18/06
Page 3 of 14 pages
TOYOTA
Procedure
TUNDRA
2007 -
TVIP V2
GLASS BREAKAGE SENSOR (GBS) (e) Dislodge the Lower Dash Cover. (Fig. 1-4) (1) Remove 2 Bolts. (2) Disconnect any Connectors.
Hood Release Lever
Nylon Panel Removal Tool, 10mm Socket
Bolt
Fig. 1-4
Bolt
Lower Dash Cover Hood Release Lever Retaining Clip
(f) Dislodge the Hood Release Lever from the Lower Dash Cover. (Fig. 1-5) (1) Press down on the Retaining Clip while pushing
the Lever out.
Fig. 1-5
Hood Release Lever
(g) Remove the Hood Latch Cable from the Hood Latch Lever. (Fig. 1-6) (h) Remove the Lower Dash Cover.
Hood Latch Cable
Fig. 1-6
10mm Socket
(i) Remove the Metal Substructure. (Fig. 1-7) (1) Remove 4 bolts. CAUTION: SHARP METAL EDGES.
Fig. 1-7 Issue: A 12/18/06
Bolts (x4)
Page 4 of 14 pages
TOYOTA
Procedure
TUNDRA
2007 -
TVIP V2
GLASS BREAKAGE SENSOR (GBS) (j) Wrap the Metal Substructure in a blanket and use the TVIP Kit Box to support it. (Fig. 1-8)
Metal Substructure
CAUTION: SHARP METAL EDGES.
TVIP Box
Fig. 1-8
FOR VEHICLES WITH COLUMN MOUNT AUTOMATIC SHIFT LEVERS ONLY. (Steps k-n) (k) Remove Vehicle Drink Holder. (Fig. 1-9) (1) Press in the tabs on each side and pull outward
on the Cup Holder.
Fig. 1-9
Phillips Screwdriver
(l) Remove the 2 bottom Screws from the Cup Holder Drawer Assembly. (Fig. 1-10)
Screws (x2)
Fig. 1-10 Issue: A 12/18/06 Page 5 of 14 pages
CONTINUED
TOYOTA
Procedure
TUNDRA
2007 -
TVIP V2
GLASS BREAKAGE SENSOR (GBS) (m) Remove the 2 top Screws. (Fig. 1-11)
Phillips Screwdriver Screws (x2)
Fig. 1-11
Nylon Panel Removal Tool
(n) Remove the Cup Holder Drawer Assembly. (Fig. 1-12)
Fig. 1-12
FOR VEHICLES WITH FLOOR MOUNT AUTOMATIC SHIFT LEVERS ONLY. (Steps o) (o) Remove the small Tray below the Climate Control Console. (Fig. 1-13) (1) Disconnect any Connectors.
Nylon Panel Removal Tool
Fig. 1-13
Tray
(p) Remove the Knockout Cover from the Climate Control Console. (Fig. 1-14) (1) Disconnect the 4P Connector from the Knockout
Cover.
(2) Discard the Knockout Cover.
Fig. 1-14 Issue: A 12/18/06
Knockout Cover
Page 6 of 14 pages
TOYOTA
Procedure
TUNDRA
2007 -
TVIP V2
GLASS BREAKAGE SENSOR (GBS) 2. GBS Microphone Installation (a) Feed the Vehicles White 4P Connector through the Climate Control Console and connect it to the GBS Microphone. (Fig. 2-1)
4P Connector
GBS Microphone
(1) Verify that the Connector is secure.
Fig. 2-1
(b) Insert the GBS Microphone into the Climate Control Console. (Fig. 2-2)
GBS Microphone
Fig. 2-2
Flat Blade Screwdriver
3. GBS ECU Preparation (a) Verify that the GBS ECU’s sensitivity is set to 5. (Fig. 3-1)
GBS ECU
Fig. 3-1 Issue: A 12/18/06 Page 7 of 14 pages
TOYOTA
Procedure
TUNDRA
2007 4. ECU installation
TVIP V2
GLASS BREAKAGE SENSOR (GBS)
10mm Socket, Extension Vehicle Brace
(a) Remove 2 Nuts from the Vehicle Brace near the Driver’s Side J/B. (Fig. 4-1) (b) Pull the Brace away from the Vehicle Reinforcement. (Fig. 4-1)
Remove Nuts (x2)
Vehicle J/B
(1) Do not remove the Brace from the studs.
Fig. 4-1
(c) Install Bracket and GBS ECU. (Fig. 4-2) (1) Make sure that the Bracket Pin seats properly.
Bracket Pin
GBS ECU
Fig. 4-2
10mm Socket, Extension M6 Flange Nut Reinstall
(d) Use the M6 Flange Nut from the supplied kit to secure the ECU Bracket in place. (Fig. 4-3) (e) Re-secure the Vehicle Brace by reinstalling 2 Nuts. (Fig. 4-3) (1) Verify that the Bracket is secure.
Reinstall
GBS ECU
Fig. 4-3
(f) Locate the Vehicle’s White 8P Connector near the Driver’s Side J/B Area. (Fig. 4-4) (1) Remove the Tape securing the Connector.
8P Connector
Fig. 4-4
Issue: A
12/18/06
Page 8 of 14 pages
TOYOTA
Procedure
TUNDRA
2007 -
TVIP V2
GLASS BREAKAGE SENSOR (GBS) (g) Connect the Vehicle Harness's White 8P Connector to the GBS ECU. (Fig. 4-5) (1) Verify that Connector is securely connected.
8P Connector
Fig. 4-5
GBS ECU
5. Warning Label Installation. (a) Using Household Windex, clean the inside of the Front Door Windows. (Fig. 5-1) (1) When cleaning with Household Windex, follow
the Manufacturer’s Directions.
Clear Tape V2 Window Label 10mm
Line Up With Bottom Text of Window Etching (or aligned with other “Factory Alarm” Labels)
(b) Place the V2 Window Labels on the inside of the Front Door Windows as shown. (Fig. 5-1) (1) Use the Labels with the Red Tag. (2) Use the ENGLISH Labels for US Vehicles.
Use the SPANISH Labels for Mexico Vehicles.
Fig. 5-1
(3) Discard the Labels without the Red Tag (4) Use a piece of clean adhesive tape to lift the
Labels off their protective backing.
DO NOT TOUCH THE ADHESIVE SURFACE OF THE WARNING LABELS. (5) Line up the Labels properly and place on the
glass. Do not attempt to reposition the Labels once they are placed.
(6) If the Label is being installed with other Window
Labels align it horizontally with the other Labels and 10mm from the last label.
Issue: A
12/18/06
Page 9 of 14 pages
TOYOTA
Procedure
TUNDRA
2007 -
TVIP V2
GLASS BREAKAGE SENSOR (GBS)
6. Completing the Installation. (a) Complete the reassembly of the Vehicle. (1) Reconnect any disconnected Connectors. (2) Verify the Panels fit together properly with no
uneven gaps between them.
Torque Wrench, 10mm Socket Negative Battery Cable
(b) Position the Negative Battery Cable at the original factory position. (Fig. 6-1) (1) Tighten the Nut to 36 in•lbf (40.67 n•cm) DO NOT TOUCH THE POSITIVE BATTERY TERMINAL. (c) Clean up and remove any trash. (d) Place the GBS Owner's Guide, sealed in the bag, in the Glove Box. (e) Discard RS3200 Plus Owners Guide, and Warranty Card. (f) Install the Short Pin. (Fig. 6-2)
Fig. 6-1
Install Short Pin
Fig. 6-2
Issue: A
12/18/06
Page 10 of 14 pages
TOYOTA
Check:
TUNDRA
2007 Look For:
TVIP V2
Checklist - these points MUST be checked to ensure a quality installation.
GLASS BREAKAGE SENSOR (GBS)
Accessory Function Checks Roll up all windows, and exit the vehicle with remote. Press and release the remote control’s lock button to start the system’s arming process. 1. The turn signal lights flash once. All doors lock. The security LED lights up. Wait 30 seconds. 2. After 30 seconds the LED starts flashing; the system is now armed. Perform the following check in a temperature- controlled environment (50º-90º F) With the tip of a key, or Striker Tool pulled all the way out (PPO only), tap the center of the driver’s door window to trigger the alarm. 3. The horn sounds repeatedly. The headlights flash repeatedly. The turn signal lights flash repeatedly. The LED lights up. NOTE: If the alarm does not trigger during functional verifications, increase the GBS sensitivity to the next setting.
For all vehicles, press the unlock button of the remote key to stop the alarm. NOTE: If you do not disarm the system, the alarm will last 20 seconds. It is not necessary to check the alarm duration.
4. The horn stops sounding. All the lights stop flashing and/ or turn off. The security LED turns off.
Issue: A
12/18/06
Page 11 of 14 pages
TOYOTA
Check:
TUNDRA
2007 Look For:
TVIP V2
Checklist - these points MUST be checked to ensure a quality installation.
GLASS BREAKAGE SENSOR (GBS)
Vehicle Function Checks Head Lights High Beams Turn Signal Lights Tail Lights Stop Lights Backup Lights Hazard Lights Marker Lights Dome/Courtesy Lights Panel/Switch Illumination Accessory Controls/Illumination (if equipped) Key Sensor Buzzer Fog Lights (if equipped) Daytime Running Lights (if equipped) Trunk/Tailgate/Bed Lights (if equipped) Glove Box Light (if equipped) Cruise Control Light (if equipped) Functioning Key Sensor Functioning Fog Lights Functioning DR Lights Functioning Lights Functioning Glove Box Light Functioning Cruise Control Light Functioning Head Lights Functioning High Beams Functioning Turn Signal Lights Functioning Tail Lights Functioning Stop Lights Functioning Backup Lights Functioning Hazard Lights Functioning Marker Lights Functioning Dome/Courtesy Lights Functioning Controls/Illumination Functioning Accessory
Issue: A
12/18/06
Page 12 of 14 pages
TOYOTA
Check:
TUNDRA
2007 Look For:
TVIP V2
Checklist - these points MUST be checked to ensure a quality installation.
GLASS BREAKAGE SENSOR (GBS) Functioning Seatbelt Warning Light. If the warning light remains "ON", it may indicate a system malfunction.
Seat Belt Warning Light
Air Bag Warning Light
Functioning Air Bag Warning Light. If the warning light remains "ON," it may indicate a system malfunction.
ABS Light (if equipped)
Functioning ABS Light. If the warning light remains "ON,” it may indicate a system malfunction.
Lamp Failure Sensor (if equipped)
Functioning Lamp Failure Light. If the warning light remains “ON,” it may indicate a system malfunction.
Track/Skid Control Light (if equipped)
Functional Track/VSC Light. If the warning light remains “ON,” it may indicate a system malfunction.
HVAC Power Locks (if equipped) Power Windows (if equipped) Power Seats (if equipped) Power Sunroof (if equipped) Horn Gauges Front Wiper/Washer Rear Wiper/Washer (if equipped) Clock (if equipped)
All HVAC Controls Function Functioning Power Locks Functioning Power Windows Functioning Power Seats Functioning Sunroof Functioning Horn Functioning Gauges Functioning Front Wiper/Washer Functioning Rear Wiper/Washer Functioning Clock
Issue: A
12/18/06
Page 13 of 14 pages
TOYOTA
Check:
TUNDRA
2007 Look For: Functioning Power Socket Functioning Starter Functioning Audio/Video Functioning Power Sliding Door Functioning Memory Settings
TVIP V2
Checklist - these points MUST be checked to ensure a quality installation.
GLASS BREAKAGE SENSOR (GBS)
Accessory Power Socket (if equipped) Starter Audio/Video (if equipped) Power Sliding Door (if equipped) Convenience Memory Settings (if equipped) Heated Seats (if equipped) Massage Seats (if equipped) Rear Window Defogger (if equipped) Power Side Mirrors (if equipped) Side Mirror Defogger (if equipped) Front Windshield Defogger (if equipped) Navigation System (if equipped) Power Back Door (if equipped) Steering Wheel Column Adjust
Functioning Heated Seats Functioning Massage Seats Functioning Rear Window Defogger Functioning Power Side Mirrors Functioning Side Mirror Defogger Functioning Front Windshield Defogger Functioning Navigation System Functioning Power Back Door Steering Wheel Column Adjusts Without Interference
Hood Latch Release Passenger Air Bag Switch (if equipped) Rollover Side Curtain Air Bag (RSCA) Switch (if equipped) Remove the Short Pin fuse after the checks are completed.
Functioning Hood Latch Release Functioning Passenger Air Bag Switch Functioning RSCA Switch
Store Short Pin Here
Issue: A
12/18/06
Page 14 of 14 pages
2007 -
TUNDRA
TVIP V5
RS3200 PLUS OWNER’S GUIDE
RS3200 PLUS
SECURITY SYSTEM DESIGNED FOR USE WITH YOUR VEHICLE’S REMOTE KEYLESS ENTRY SYSTEM
OWNER’S GUIDE
Rev. A 06/20/05
TOYOTA RS3200 PLUS Security system
Page 1
To better understand the features and functions of this security system, please read this Owner’s Guide completely prior to use.
TABLE OF CONTENTS
DESCRIPTION INTRODUCTION BRIEF DESCRIPTION–RS3200 PLUS FEATURES OPERATION
ARMING THE RS3200 PLUS (except PASSIVE ARMING) DISARMING THE RS3200 PLUS (except PASSIVE DISARMING) PASSIVE (AUTOMATIC) ARMING & DISARMING AUTOMATIC REARMING ARMING SUSPENSION
PAGE
2 3, 4 5 6 7 8 8 9 9 10 10 11 12
IN
ALARM INFORMATION
ALARM TRIGGERS ALARM DESCRIPTIONS STOPPING AN ALARM
GLASS BREAKAGE SENSOR INFORMATION
GLASS BREAKAGE SENSOR CHECK PROCEDURE
PROGRAMMING
PASSIVE (AUTOMATIC) ARMING AND ENTRY DELAY (Not applicable to Highlander and Sienna. Please consult your Toyota Dealer for programming information.)
WARNING and CAUTION INFORMATION IN B C O
13
C
Par lea
Page 2
TOYOTA RS3200 PLUS Security system
INTRODUCTION
Congratulations on your choice of the RS3200 PLUS add-on security system to protect your vehicle! To get the most from the system, we strongly recommend that you read this Owner’s Guide completely to learn all of its features and functions. The RS3200 PLUS provides security through point-of-entry monitoring, glass breakage detection and ignition switch monitoring. While ARMED, the system will be TRIGGERED and sound an ALARM when a door, trunk or hatch is forcibly unlocked or opened*, or when a window is tapped on or broken. During the ALARM, the vehicle’s horn sounds and the headlights, tail lights and front marker or turn signal lights flash. A l s o , the vehicle’s starter is disabled, preventing engine start. In addition to the comprehensive protection, the RS3200 PLUS works in conjunction with your vehicle’s remote keyless entry system, enabling you to ARM and DISARM the security system at the same time the doors are remotely locked and unlocked. In vehicles equipped with a buzzer, it will chirp when the system is REMOTE ARMED and DISARMED. An important note about your system Throughout this guide, there are references to the STATUS MONITOR for this system. Illustrated below, this panel holds the LED indicator (for the system’s operating status) and the GLASS BREAKAGE SENSOR’S microphone. In vehicles equipped with an engine immobilizer system, there is a LED already installed, so the RS3200 PLUS utilizes the vehicle’s engine immobilizer system LED➂ instead and a microphone mounted in a separate location. If your vehicle falls into this category, remember to look at that LED when the information refers to the STATUS MONITOR. If you do not know where the LED is located, refer to your vehicle’s owner’s guide for specific information.
➀➁
➀
* When the system is PASSIVELY (AUTOMATICALLY) ARMED, there is an ENTRY DELAY that will elapse when a door is opened before an ALARM is TRIGGERED.
untos de entrada, detección as esté armado, el sistema se etero sea desasegurado o vez que se dispara la el frente, las luces traseras y del vehículo queda a protección que ofrece el ntrol remoto de entrada sin ridad al mismo tiempo que los ehículos equipados con desarmado a control remoto.
LIGHTS FOR 30 SECONDS (PREARMING) THEN STARTS FLASHING (SYSTEM IS ARMED)
➁
➂
YOUR ENGINE IMMOBILIZER SYSTEM LED MAY LOOK DIFFERENT THAN THE ONE ILLUSTRATED HERE
monitor 1 2 del sistema. (1) (2) ca el estatus de operación del uipados con sistemas de l sistema RS3200 Plus ez en una ubicación distinta. cuando la información se ubicado dicho LED, refiérase
irá un retraso de
IÓN DEL MOTOR DIFERENTE DEL
Plus para la protección de ndamos que por favor lea das sus funciones y
RAMOS AQUÍ. L SISTEMA DE
TOYOTA RS3200 PLUS Security system
**
Page 3
C A
I
I
BRIEF DESCRIPTION–RS3200 PLUS FEATURES
FEATURES
FUNCTIONS
The RS3200 PLUS will ARM 30 seconds after the lock button on the remote REMOTE keyless entry system’s remote control is pressed, and DISARM when the ARMING/DISARMING unlock button is pressed. If your vehicle is equipped with a buzzer that chirps when the lock and unlock buttons on the remote controls are pressed, the buzzer will also chirp when the system is REMOTE ARMED and DISARMED. The RS3200 PLUS will automatically REARM at the same time the AUTOMATIC vehicle’s remote keyless entry system relocks the vehicle’s REARMING doors, if no door is opened within 30 seconds after REMOTE DISARMING. The RS3200 PLUS will ARM 30 seconds after you close the trunk (if KEY open) and lock the vehicle’s doors with the key, and will DISARM when ARMING/DISARMING you unlock a door with the key. While ARMED, the trunk may be opened with the key (or trunk release button ARMED MODE SUSPENSION** on your remote control, if so equipped) without TRIGGERING an ALARM. Once the open trunk is closed, the system ARMS again. The RS3200 PLUS may be programmed to automatically ARM 30 PASSIVE (AUTOMATIC) seconds after the ignition key is removed, the vehicle exited and the ARMING last door and the trunk closed, without the necessity of locking doors. The RS3200 PLUS may be DISARMED with the vehicle’s ignition key PASSIVE DISARMING after it was PASSIVELY ARMED. ADJUSTABLE ENTRY When the RS3200 PLUS has been PASSIVELY ARMED, an ENTRY DELAY DELAY (user-selectable at 0, 15, or 30 seconds) will start when a door is opened before an ALARM is TRIGGERED. When you lock the vehicle with the central lock switch (while a door MANUAL ARMING is open), the RS3200 PLUS will ARM 30 seconds after you close all the doors and the trunk (if open). The RS3200 PLUS may be DISARMED by inserting the key into the IGNITION KEY ignition switch and turning it to “ON.” DISARMING Forcibly unlocking or opening a door or trunk while the RS3200 PLUS POINT-OF-ENTRY is ARMED will TRIGGER an ALARM immediately. (If the system was PASSIVELY PROTECTION ARMED, the ENTRY DELAY must pass after opening a door before the ALARM is TRIGGERED.) The RS3200 PLUS utilizes a microphone (usually mounted in the GLASS BREAKAGE STATUS MONITOR) to sense the noise from tapping on window glass, or SENSOR glass breaking, and TRIGGER the system to sound an ALARM. It is fine tuned to “listen” for this type of noise, and ignore other sounds. WARN AWAY ALARM When the GLASS BREAKAGE SENSOR’S microphone picks up tapping or breaking of window glass, it TRIGGERS a WARN AWAY ALARM; the headlights and tail and marker or turn signal lights flash, and the horn sounds for 20 seconds, but the starter is not disabled. If there is another detection of glass tapping or breaking, or if a door is opened or unlocked without a key, the regular ALARM is TRIGGERED. While ARMED, the RS3200 PLUS monitors the ignition switch. If an attempt is IGNITION SWITCH made to start the vehicle without a key, an ALARM is TRIGGERED. MONITORING
**Starting from 2002 M.Y., Arming Suspension Mode by using the key to unlock the trunk is not applicable to Camry, Solara, and Corolla.
A A S P P T A T E P A ( S A L A A
Page 4
TOYOTA RS3200 PLUS Security system
BRIEF DESCRIPTION–RS3200 PLUS FEATURES
FEATURES
FUNCTIONS
* TRIGGER MEMORY is not available for Corolla / Matrix.
erra los seguros de las ntre levantado y continúa a. urante su ausencia se haya funcionamiento, al ces delanteras y traseras
S DEL SISTEMA
terrumpido mientras el ez restablecida, la alarma
un zumbador que suena istema a control remoto sin bador también sonará do a distancia. lus activa el claxon del
eshabilita el encendido del rrancado hasta que el
Plus monitorea el interruptor arranque del vehículo sin la
as e intermitentes cada vez el sistema y cuando se ás se encienden las luces
rotura de cristales y al LED eración del sistema de el LED del inmobilizador del arado).
atrix.
When an ALARM is TRIGGERED, the system disables the vehicle’s STARTER DISABLE starter and prevents engine start until the system is reset (DISARMED). During an ALARM, the system will lock the doors if one is unlocked, FORCED LOCK and will continue to do so for the duration of the ALARM. DURING ALARM The user is notified that an ALARM occurred. Upon DISARMING the TRIGGER MEMORY * system after an ALARM was TRIGGERED, the vehicle’s tail and marker lights will be turned on for 2 seconds. The RS3200 PLUS flashes the vehicle’s tail and marker or turn signal lights EXTERIOR LIGHT during REMOTE ARMING and REMOTE DISARMING, and during an ALARM. ACTIVATION Also, during an ALARM the headlights flash. If your vehicle is equipped with a buzzer that chirps when the lock BUZZER ACTIVATION and unlock buttons on the remote keyless entry system’s remote controls are pressed, the buzzer will also chirp when the system is REMOTE ARMED and DISARMED. HORN ACTIVATION During an ALARM, the RS3200 PLUS activates the vehicle’s horn. If power to the RS3200 PLUS is disrupted while it is ARMED, an ALARM is POWER LOSS MEMORY TRIGGERED once power is restored. This panel houses the GLASS BREAKAGE SENSOR microphone and the STATUS MONITOR flashing LED that indicates the operating status of the security system. (Some vehicle applications utilize the vehicle’s engine immobilizer system LED and a separate microphone, instead.)
TOYOTA RS3000 PLUS Security system
Page 5
* ∆E El
OPERATION
ARMING THE RS3200 PLUS (except PASSIVE ARMING)
The system may be ARMED in several ways. Do one of the following: Lock the doors with your key: Remove the key from the ignition switch. Exit the vehicle, and close all the doors.* Close the trunk or hatch, if necessary.* Insert the key into the door key switch and turn it toward the front of the vehicle: The STATUS MONITOR’S LED turns on for 30 seconds, then starts flashing.➀ The system is now ARMED. Lock the doors from inside the vehicle: Remove the key from the ignition switch. Open the driver’s or front passenger’s door. Push the central lock switch. Exit the vehicle, and close all the doors.* Close the trunk or hatch, if necessary.* Then: The STATUS MONITOR’S LED turns on for 30 seconds, then starts flashing.➀ The system is now ARMED. Lock the doors with the remote control: Remove the key from the ignition switch. Exit the vehicle, and close all the doors.* Close the trunk or hatch, if necessary.* Press the lock button on the remote control. Simultaneously: The doors lock.➁ The vehicle’s tail and marker or turn signal lights flash once.③ The vehicle’s buzzer chirps once.∆ The STATUS MONITOR’S LED turns on for 30 seconds, then starts flashing.➀ The system is now ARMED.
AR
O
PR DE LA
GIR
PR Q
1
TURN TOWARD THE FRONT OF THE VEHICLE PUSH THE LOCK SWITCH WHILE THE DOOR IS OPEN PRESS AND RELEASE THE LOCK BUTTON
➀
LIGHTS FOR 30 SECONDS (PREARMING) THEN FLASHES (SYSTEM IS ARMED)
➁
③
ALL DOORS LOCK WHEN THE SYSTEM IS REMOTE ARMED
THE TAIL AND MARKER OR TURN SIGNAL LIGHTS FLASH ONCE WHEN THE SYSTEM IS REMOTE ARMED
* The system will not ARM while any of the doors, trunk or hatch is open. ∆ If your vehicle is equipped with a buzzer.
Page 6
TOYOTA RS3200 PLUS Security system
The system may be DISARMED in several ways. Do one of the following: Unlock the doors with your key: Insert the key into the door key switch and turn it toward the rear of the vehicle: The STATUS MONITOR’S LED stops flashing.➀The system is now DISARMED.*
TURN TOWARD THE REAR OF THE VEHICLE
PUSH THE UNLOCK BUTTON
➀
STOPS FLASHING WHEN THE SYSTEM IS DISARMED
➁
➂
* Please note, if the system utilizes your vehicle’s engine immobilizer system LED instead of the STATUS MONITOR, the LED will continue to flash. ∆ If your vehicle is equipped with a buzzer.
IVO)
THE TAIL AND MARKER OR TURN SIGNAL LIGHTS FLASH TWICE WHEN THE SYSTEM IS REMOTE DISARMED
siguientes:
THE DRIVER’S DOOR UNLOCKS WHEN THE SYSTEM IS REMOTE DISARMED
unner, también podrá desde la puerta trasera; ismo tiempo.
NOTE: If your vehicle’s tail and marker or turn signal lights turn on for 2 seconds when the system is DISARMED,* the TRIGGER MEMORY was activated; something TRIGGERED an ALARM while you were away from the vehicle. This feature is not available for Corolla / Matrix.
remoto: tas desde el control remoto.
TURN THE KEY TO “ON” TO DISARM THE SYSTEM
This method of disarming is rarely used. You must be inside the vehicle while the system is armed in order to do it.
3 lo centellearán dos veces. (3) ∆ 1 dejará de parpadear. (1)
Use the ignition switch: Insert the key into the ignition switch, then turn it to ON. The STATUS MONITOR’S LED stops flashing.➀The system is now DISARMED.*
: , después gírela a la posición
tas nuevamente dentro de ber desasegurado la puerta las puertas.
usado. Usted deberá se encuentre armado
y gírela hacia la parte trasera
1 dejará de parpadear. (1)
Unlock the doors with the remote control: Press the unlock button on the remote control. Simultaneously: The driver’s door unlocks.➁ The vehicle’s tail and marker or turn signal lights flash twice.➂ The vehicle’s buzzer chirps twice.∆ The STATUS MONITOR’S LED stops flashing.➀The system is now DISARMED.* Press the unlock button again within 3 seconds after unlocking the driver’s door to unlock the remaining doors.
segundos al desarmar el go hizo sonar la alarma
In the case of Highlander, Sienna, and 4Runner, you may also disarm the system using the key in the back door; all doors will unlock at the same time.
ERAS E INTERMITENTES PARPADEAN DOS
SARMAR REMOTAMENTE AL SISTEMA
DISARMING THE RS3200 PLUS (except PASSIVE DISARMING)
del vehículo para rpadeando.
1 a dejará de parpadear. (1)
OPERATION
TOYOTA RS3200 PLUS Security system
Page 7
Ta NO
EL
SEG
DO L
EN
*S do so su C de ha ab de 15 po la
OPERATION
PASSIVE (AUTOMATIC) ARMING & DISARMING
When the RS3200 PLUS is programmed to PASSIVELY ARM, the system will ARM after the ignition key is removed and all doors and the trunk are closed; you do not need to lock the doors. When you come back to your vehicle and open a door, you must insert the key into the ignition switch and turn it to “ON” during the ENTRY DELAY (0, 15 or 30 seconds), or an ALARM will be TRIGGERED. If you lock the doors, regular ARMING will override PASSIVE ARMING; there will be no ENTRY DELAY. See the PROGRAMMING information on page 13 to activate the PASSIVE ARMING mode, as well as to select the ENTRY DELAY time. (Not applicable to Highlander and Sienna. Please consult your Toyota Dealer for programming information .) To PASSIVELY ARM the system: Remove the key from the ignition switch. Exit the vehicle, and close all the doors. (The system will not ARM while any of the doors are open.) Close the trunk or hatch, if necessary. (The system will not ARM while the trunk or hatch is open.) After the last door, trunk or hatch is closed: The STATUS MONITOR’S LED turns on for 30 seconds, then starts flashing.➀The system is now ARMED.
A
O
1
E
THE SYSTEM ARMS 30 SECONDS AFTER THE LAST ENTRY POINT (DOOR, TRUNK OR HATCH) IS CLOSED
THE SYSTEM DISARMS WHEN YOU INSERT THE KEY AND TURN IT TO “ON”
To DISARM the PASSIVELY ARMED system: Enter the vehicle through a front door. The ENTRY DELAY begins: The STATUS MONITOR’S LED turns on (no flashing.)➁ Insert the key into the ignition switch and turn it to “ON” before the ENTRY DELAY ends.* The LED turns off. The system is now DISARMED. You may also DISARM the system following any of the methods described on page 6.
NOTE: If your vehicle’s tail and marker lights turn on for 2 seconds when the ignition key is turned to “ON”, the TRIGGER MEMORY was activated; something TRIGGERED an ALARM while you were away from the vehicle. This feature is not available for Corolla/Matrix. ➀
LIGHTS FOR 30 SECONDS (PRE-ARMING) THEN STARTS FLASHING (SYSTEM IS ARMED)
➁
TURNS ON (NO FLASHING) DURING THE ENTRY DELAY
* If the ENTRY DELAY time elapses before the ignition switch is turned to “ON”, an ALARM will be TRIGGERED. To DISARM the system during an ALARM, insert the ignition key and turn it to “ON”, or press and release the remote control’s unlock button.
Page 8
TOYOTA RS3200 PLUS Security system
OPERATION
AUTOMATIC REARMING
When you unlock the doors using the remote control, the RS3200 PLUS is DISARMED at the same time. However, if you do not open a door or the trunk within 30 seconds, the keyless entry system will relock the doors and the RS3200 PLUS will REARM 30 seconds later. How the RS3200 PLUS automatically REARMS:
0
45
15
30
THE DOORS ARE UNLOCKED BY PRESSING THE UNLOCK BUTTON ON THE REMOTE CONTROL...
WHEN NO DOOR, TRUNK OR HATCH IS OPENED...
FOR MORE THAN 30 SECONDS...
The ARMED state of the RS3200 PLUS can be suspended temporarily by using the key to unlock and open the trunk. If your remote control is so equipped, you may also suspend the ARMED state using the trunk release button➀to open the trunk. When the ARMING is suspended, the STATUS MONITOR’S LED will turn off ➁until the trunk is closed again. ➀ ➁
TURNS OFF WHEN THE ARMED STATE IS SUSPENDED
OPENING THE TRUNK SUSPENDS THE ARMED STATE OF THE SECURITY SYSTEM
RS3200 Plus se desarmará al o dentro de los 30 segundos 30 segundos más tarde se
E ENTRADA SIN MÁTICAMENTE
EL LED
SE ENCENDERÁ
**Starting from 2002 M.Y., Arming Suspension Mode by using the key to unlock the trunk is not applicable to Camry, Solara, and Corolla.
lmente al emplear la llave to tenga la función para otón para abrir el maletero a e monitorea el condición se
ARMING SUSPENSION**
THE KEYLESS THE LED WILL ENTRY LIGHT UP FOR 30 SYSTEM AUTOMATSECONDS ICALLY RELOCKS (PRE-ARM), THEN THE DOORS, THEN FLASH WHEN THE THE RS3200 PLUS SYSTEM IS ARMED AUTOMATICALLY REARMS.
los automóviles modelo tado de suspensión del abrir el maletero no estará para el Camry, Solara y
AS PUERTAS, Y TEMA RS3200 TICAMENTE SE RMA POR 30 SEGUNDOS (PRE-ARMADO) Y LUEGO PARPADEARÁ CUANDO EL SISTEMA ESTÉ ARMADO
TOYOTA RS3200 PLUS Security system
Page 9
ALARM INFORMATION
ALARM TRIGGERS
While the system is ARMED, an ALARM will be TRIGGERED when any of the following occurs:
➤
Forcibly opening a door, or the trunk or hatch without a key Pulling the trunk release lever inside the vehicle will also TRIGGER an ALARM.
➤
Manually unlocking a door Manually operating an inside lock button will TRIGGER an ALARM. Note: Because this action will TRIGGER an ALARM, it is important that you do not ARM the system while someone is in the vehicle.
➤
“Hot wiring” the vehicle The RS3200 PLUS can detect the absence of the ignition key if the ignition circuit is shorted in attempt to start the vehicle.
➤
Tapping on or breaking the glass The noise from tapping on, or breaking of glass TRIGGERS a WARN AWAY ALARM first, then a regular ALARM. See the description of how the GLASS BREAKAGE SENSOR TRIGGERS ALARMS on page 12.
➤
Mie las
Power restoration If power to the system is interrupted while it is ARMED, an ALARM will be TRIGGERED immediately when power is restored.
CO
IN
Page 10
TOYOTA RS3000 PLUS Security system
ALARM DESCRIPTIONS
Regular ALARM ➀ When an ALARM is triggered in any way other than initial detection by the GLASS BREAKAGE SENSOR, the following occur: The horn sounds repeatedly for 60 seconds. The headlights flash repeatedly for 60 seconds. The tail and marker or turn signal lights flash repeatedly for 60 seconds. The starter is disabled (no engine start) until the system is DISARMED. The door lock will be relocked if someone reaches in and unlocks the inside lock button. After 60 seconds of ALARM, the system will REARM and continue to protect the vehicle.
➀
THE HORN SOUNDS FOR 60 SECONDS
THE STARTER IS DISABLED UNTIL THE SYSTEM IS DISARMED MARKER OR TURN SIGNAL LIGHTS FLASH FOR 60 SECONDS
TAIL OR TURN SIGNAL LIGHTS FLASH FOR 60 SECONDS
WARN-AWAY ALARM ➁ Upon initial detection of noise from tapping on, or breaking glass, the GLASS BREAKAGE SENSOR TRIGGERS a WARN AWAY ALARM: The horn sounds repeatedly for 20 seconds. The headlights flash repeatedly for 20 seconds. The tail and marker or turn signal lights flash repeatedly for 20 seconds. If the GLASS BREAKAGE SENSOR detects noise again, or if a door or trunk is opened while the system is still ARMED, the regular ALARM (described above) is activated.
➁
THE HORN SOUNDS FOR 20 SECONDS TAIL OR TURN SIGNAL LIGHTS FLASH FOR 20 SECONDS
Simply DISARM the system using the remote control or key as described on page 6.
rimera señal de advertencia
STOPPING AN ALARM
segundos. undos. á ser arrancado el motor)
HEADLIGHTS FLASH FOR 20 SECONDS MARKER OR TURN SIGNAL LIGHTS FLASH FOR 20 SECONDS
ndo con la protección del
lguien los abriera
o romper algún cristal, el
HEAD LIGHTS FLASH FOR 60 SECONDS
segundos. undos. evamente, o si alguna puerta larma regular (descrita
ve, como se describió en la
TRASERAS Y LAS INTERMITENTES
ALARM INFORMATION
LAS
Y LAS INTERMITENTES PARPADEARÁN POR 60 SEGUNDOS
PARPADEARÁN DURANTE 20 SEGUNDOS
LAS
LUCES TRASERAS
LUCES
TOYOTA RS3200 PLUS Security system
Page 11
GLASS BREAKAGE SENSOR INFORMATION
The RS3200 PLUS provides protection for your vehicle above and beyond entry point monitoring–it “listens” for the noise made by tapping on, or breaking of glass. Using a microphone designed specifically for this task, the GLASS BREAKAGE SENSOR is capable of ignoring other noises, which helps to prevent “false alarms” from occurring.
GLASS BREAKAGE SENSOR CHECK PROCEDURE
When the RS3200 PLUS was installed in your vehicle, care was taken to adjust the sensitivity level of the GLASS BREAKAGE SENSOR. You may observe how it works following the procedure listed below. 1. ARM the system. Press the lock button on the remote control or lock the doors with the key. (Remember, the system will not ARM if any door, the trunk or hatch is open.)
2.
Wait until the STATUS MONITOR’S LED starts flashing. The LED will flash 30 seconds after the last door, the trunk or hatch is closed.
3.
With the tip of a key, tap the center of the driver’s door window. Tap the glass with light to moderate force. WARNING: Do not hit the glass with excessive force, especially in cold weather, or you may crack or break it.
Cu cris pro
A WARN AWAY ALARM should be TRIGGERED. If the ALARM is not TRIGGERED, make sure you performed the procedure correctly and try again. If you find that the system did not perform as expected, contact your Toyota dealer for more information. 4. DISARM the system to stop the WARN AWAY ALARM. Press the unlock button on the remote control or use the key to DISARM the system.
P C
El ést un cris
IN
Page 12
TOYOTA RS3200 PLUS Security system
PROGRAMMING
. El sistema desasegurará la puerta en dos segundos; si esto no sucede, empiece nuevamente. El proceso de programación ha terminado. e pasivamente. Para cambiar áticamente), así como para uación. Para mayor o se aplica para el mación acerca de la prograetire la llave del cilindro de veces; este procedimiento pletar en el espacio de cinco pacio de 40 segundos.) re el seguro la puerta del ductor. cierre la d. Asegure y despus desasegure tres del veces el seguro tor. interno de la puerta del conductor. pasos en menos de 40 de programación. PASIVO. SELECCIÓN DEL The RS3200 PLUS is factory-set to not PASSIVELY ARM. To change the system’s operation for PASSIVE ARMING operation, as well as adjust the ENTRY DELAY time, follow the procedure below. For more information on this feature, please refer to page 7. (Not applicable to Highlander and Sienna. Please consult your Toyota Dealer for programming information.)
PASSIVE ARMING ON/OFF SELECTION, ENTRY DELAY TIME SELECTION
1. Before you begin: 2. Open the driver’s door. Close the remaining doors and the trunk or hatch. Unlock all doors with the inside lock switch. Remove the key from the ignition switch. Insert and remove the key from the ignition key cylinder 3 times; this must be completed within 5 seconds.
Start the Programming Procedure. (Complete these steps within 40 seconds.)
a. Close the driver’s door.
b. Lock and unlock all doors 3 times by key or remote control.
c. Open and close d. Lock, then unlock the driver’s door the driver’s door. inside lock button 3 times.
e. Open the driver’s door.
f.
The system locks the door in 2 seconds; if this does not happen, start over.
g. Unlock the driver’s door knob.
3. Select the Operating Mode and Complete the Programming Procedure.
a. Close, then Open the driver’s door: b. Lock then unlock the c. The system locks the 2 times = PASSIVE ARMING OFF driver’s door inside lock door in 2 seconds; if this 3 times = PASSIVE ARMING ON, does not happen, start button 1 time. 0 Sec. ENTRY DELAY over. Programming is now 4 times = PASSIVE ARMING ON, complete. 15 Sec. ENTRY DELAY 5 times = PASSIVE ARMING ON, 30 Sec. ENTRY DELAY
TOYOTA RS3200 PLUS Security system
Page 13
Warning
• • • •
This product is applicable only to vehicles with 12V DC, negative grounding specifications. Do not use in vehicles with 24V specifications. Otherwise, damage to the unit or a fire may result. Never attempt to disassemble or modify the product. Otherwise, an accident, fire or electric shock may result. When replacing fuses, be sure to use fuses with the same specified capacity (amperage.) Otherwise, damage to the unit or vehicle, fire or electric shock may result. If an abnormal condition occurs, such as liquids spilling onto the product, or the product emitting smoke or strange odors, stop using it immediately and consult the dealer from whom you purchased the product. Continued use of the product before corrective actions are taken may result in an accident, injury or fire. Never pull the plastic bag over your head. Otherwise, a serious injury or death from suffocation may occur.
•
• • • • • • •
Caution
• •
Do not use this product for applications other than in-vehicle use. Otherwise, an electric shock or injury may result. Do not allow children to play with the remote controls. Otherwise, the doors may be locked or unlocked, the security system armed or disarmed, or an alarm triggered unintentionally. If this product is dropped or its case is damaged, disconnect the power supply lead and contact the dealer from whom you purchased it to obtain service. Otherwise, a fire or electric shock may result.
• l l i
•
090002-28940700
02-28940700
Preparation
TUNDRA
2007 -
TVIP V2
GLASS BREAKAGE SENSOR (GBS)
NOTE: Part number of this accessory may not be the same as the part number shown.
Part Number: 08586-OC890
Conflicts
Do not install into vehicles without Factory Alarm Systems.
Recommended Tools
Personal & Vehicle Protection Safety Glasses Safety Gloves Vehicle Protection Special Tools Striker Tool (PPO only) Installation Tools Phillips Head Screwdriver Flat Blade Screwdriver Nylon Panel Removal Tool Torque Wrench Clear Tape Socket Special Chemicals Cleaner Glass Cleaner Notes
Recommended Sequence of Application
Item # 1 2 Accessory TVIP/RES XM Radio Any TVIP or RES system *Mandatory
(Optional) Blankets, Parts Boxes Notes
CAD-E IADS P/N ALL 02016-01
Kit Contents
Item # 1 Quantity 1 Description GBS ECU w/bracket attached
Notes #2, screwdriver or tip 1/8” wide screwdriver e.g. Panel Pry Tool #1
Toyota SST # 00002-06001-01 36 in•bf (40.67 n•cm)
Hardware Bag Contents
Item # 1 2 3 4 5 6 7 8 9 Quantity 1 1 2 2 2 2 1 1 1 Description M6 Flange Nut GBS Microphone V2 Window Label w/ red tag V2 Window Label w/ red tag SPANISH V5 Window Label (discard) V5 Window Label SPANISH (discard) V2 Owner’s Guide V5 Owner’s Guide (discard) Warranty Card
10mm, Extension Notes VDC approved cleaner Household Windex
Legend
STOP: Damage to the vehicle may occur. Do not proceed until process has been complied with. OPERATOR SAFETY: Use caution to avoid risk of injury. CAUTION: A process that must be carefully observed in order to reduce the risk of damage to the accessory/vehicle and to ensure a quality installation. TOOLS & EQUIPMENT: Used in Figures calls out the specific tools and equipment recommended for this process. REVISION MARK: This mark highlights a change in installation with respect to previous issue.
Additional Items Required For Installation
Item # Quantity Description
Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this accessory should follow approved guidelines to ensure a quality installation These guidelines can be found in the "Accessory Installation Practices" document. This document covers such items as: • Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.). • Safety (eye protection, rechecking torque procedure, etc.). • Vehicle Disassembly/Reassembly (panel removal, part storage, etc.). • Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.). Please see your Toyota dealer for a copy of this document Issue: A 12/18/06 Page 1 of 14 pages
TOYOTA
Preparation A GBS ECU
GBS Microphone
TUNDRA
2007 -
TVIP V2
GLASS BREAKAGE SENSOR (GBS)
B
Issue: A
12/18/06
Page 2 of 14 pages
TOYOTA
Procedure
TUNDRA
2007 1. Vehicle Disassembly
TVIP V2
GLASS BREAKAGE SENSOR (GBS)
(a) Vehicles with Automatic Transmission should be placed in Park and have the Parking Brake set before disconnecting the Battery.
10mm Socket Negative Battery Cable
(b) Remove the Negative Battery Cable. (Fig. 1-1) (1) Protect the Fender before starting. (2) Note the Battery Cable Position, as it will be reinstalled in the same position.
DO NOT TOUCH THE POSITIVE BATTERY TERMINAL.
Fig. 1-1
Nylon Panel Removal Tool Step Cover
(c) Remove the Driver’s Step Cover. (Fig. 1-2) (1) Begin by protecting the Vehicle Interior with
Blankets.
Fig. 1-2
Cowl Cover
(d) Remove the Driver’s Cowl Cover. (Fig. 1-3) (1) Remove 1 Cowl Nut.
Cowl Nut
Fig. 1-3
Issue: A
12/18/06
Page 3 of 14 pages
TOYOTA
Procedure
TUNDRA
2007 -
TVIP V2
GLASS BREAKAGE SENSOR (GBS) (e) Dislodge the Lower Dash Cover. (Fig. 1-4) (1) Remove 2 Bolts. (2) Disconnect any Connectors.
Hood Release Lever
Nylon Panel Removal Tool, 10mm Socket
Bolt
Fig. 1-4
Bolt
Lower Dash Cover Hood Release Lever Retaining Clip
(f) Dislodge the Hood Release Lever from the Lower Dash Cover. (Fig. 1-5) (1) Press down on the Retaining Clip while pushing
the Lever out.
Fig. 1-5
Hood Release Lever
(g) Remove the Hood Latch Cable from the Hood Latch Lever. (Fig. 1-6) (h) Remove the Lower Dash Cover.
Hood Latch Cable
Fig. 1-6
10mm Socket
(i) Remove the Metal Substructure. (Fig. 1-7) (1) Remove 4 bolts. CAUTION: SHARP METAL EDGES.
Fig. 1-7 Issue: A 12/18/06
Bolts (x4)
Page 4 of 14 pages
TOYOTA
Procedure
TUNDRA
2007 -
TVIP V2
GLASS BREAKAGE SENSOR (GBS) (j) Wrap the Metal Substructure in a blanket and use the TVIP Kit Box to support it. (Fig. 1-8)
Metal Substructure
CAUTION: SHARP METAL EDGES.
TVIP Box
Fig. 1-8
FOR VEHICLES WITH COLUMN MOUNT AUTOMATIC SHIFT LEVERS ONLY. (Steps k-n) (k) Remove Vehicle Drink Holder. (Fig. 1-9) (1) Press in the tabs on each side and pull outward
on the Cup Holder.
Fig. 1-9
Phillips Screwdriver
(l) Remove the 2 bottom Screws from the Cup Holder Drawer Assembly. (Fig. 1-10)
Screws (x2)
Fig. 1-10 Issue: A 12/18/06 Page 5 of 14 pages
CONTINUED
TOYOTA
Procedure
TUNDRA
2007 -
TVIP V2
GLASS BREAKAGE SENSOR (GBS) (m) Remove the 2 top Screws. (Fig. 1-11)
Phillips Screwdriver Screws (x2)
Fig. 1-11
Nylon Panel Removal Tool
(n) Remove the Cup Holder Drawer Assembly. (Fig. 1-12)
Fig. 1-12
FOR VEHICLES WITH FLOOR MOUNT AUTOMATIC SHIFT LEVERS ONLY. (Steps o) (o) Remove the small Tray below the Climate Control Console. (Fig. 1-13) (1) Disconnect any Connectors.
Nylon Panel Removal Tool
Fig. 1-13
Tray
(p) Remove the Knockout Cover from the Climate Control Console. (Fig. 1-14) (1) Disconnect the 4P Connector from the Knockout
Cover.
(2) Discard the Knockout Cover.
Fig. 1-14 Issue: A 12/18/06
Knockout Cover
Page 6 of 14 pages
TOYOTA
Procedure
TUNDRA
2007 -
TVIP V2
GLASS BREAKAGE SENSOR (GBS) 2. GBS Microphone Installation (a) Feed the Vehicles White 4P Connector through the Climate Control Console and connect it to the GBS Microphone. (Fig. 2-1)
4P Connector
GBS Microphone
(1) Verify that the Connector is secure.
Fig. 2-1
(b) Insert the GBS Microphone into the Climate Control Console. (Fig. 2-2)
GBS Microphone
Fig. 2-2
Flat Blade Screwdriver
3. GBS ECU Preparation (a) Verify that the GBS ECU’s sensitivity is set to 5. (Fig. 3-1)
GBS ECU
Fig. 3-1 Issue: A 12/18/06 Page 7 of 14 pages
TOYOTA
Procedure
TUNDRA
2007 4. ECU installation
TVIP V2
GLASS BREAKAGE SENSOR (GBS)
10mm Socket, Extension Vehicle Brace
(a) Remove 2 Nuts from the Vehicle Brace near the Driver’s Side J/B. (Fig. 4-1) (b) Pull the Brace away from the Vehicle Reinforcement. (Fig. 4-1)
Remove Nuts (x2)
Vehicle J/B
(1) Do not remove the Brace from the studs.
Fig. 4-1
(c) Install Bracket and GBS ECU. (Fig. 4-2) (1) Make sure that the Bracket Pin seats properly.
Bracket Pin
GBS ECU
Fig. 4-2
10mm Socket, Extension M6 Flange Nut Reinstall
(d) Use the M6 Flange Nut from the supplied kit to secure the ECU Bracket in place. (Fig. 4-3) (e) Re-secure the Vehicle Brace by reinstalling 2 Nuts. (Fig. 4-3) (1) Verify that the Bracket is secure.
Reinstall
GBS ECU
Fig. 4-3
(f) Locate the Vehicle’s White 8P Connector near the Driver’s Side J/B Area. (Fig. 4-4) (1) Remove the Tape securing the Connector.
8P Connector
Fig. 4-4
Issue: A
12/18/06
Page 8 of 14 pages
TOYOTA
Procedure
TUNDRA
2007 -
TVIP V2
GLASS BREAKAGE SENSOR (GBS) (g) Connect the Vehicle Harness's White 8P Connector to the GBS ECU. (Fig. 4-5) (1) Verify that Connector is securely connected.
8P Connector
Fig. 4-5
GBS ECU
5. Warning Label Installation. (a) Using Household Windex, clean the inside of the Front Door Windows. (Fig. 5-1) (1) When cleaning with Household Windex, follow
the Manufacturer’s Directions.
Clear Tape V2 Window Label 10mm
Line Up With Bottom Text of Window Etching (or aligned with other “Factory Alarm” Labels)
(b) Place the V2 Window Labels on the inside of the Front Door Windows as shown. (Fig. 5-1) (1) Use the Labels with the Red Tag. (2) Use the ENGLISH Labels for US Vehicles.
Use the SPANISH Labels for Mexico Vehicles.
Fig. 5-1
(3) Discard the Labels without the Red Tag (4) Use a piece of clean adhesive tape to lift the
Labels off their protective backing.
DO NOT TOUCH THE ADHESIVE SURFACE OF THE WARNING LABELS. (5) Line up the Labels properly and place on the
glass. Do not attempt to reposition the Labels once they are placed.
(6) If the Label is being installed with other Window
Labels align it horizontally with the other Labels and 10mm from the last label.
Issue: A
12/18/06
Page 9 of 14 pages
TOYOTA
Procedure
TUNDRA
2007 -
TVIP V2
GLASS BREAKAGE SENSOR (GBS)
6. Completing the Installation. (a) Complete the reassembly of the Vehicle. (1) Reconnect any disconnected Connectors. (2) Verify the Panels fit together properly with no
uneven gaps between them.
Torque Wrench, 10mm Socket Negative Battery Cable
(b) Position the Negative Battery Cable at the original factory position. (Fig. 6-1) (1) Tighten the Nut to 36 in•lbf (40.67 n•cm) DO NOT TOUCH THE POSITIVE BATTERY TERMINAL. (c) Clean up and remove any trash. (d) Place the GBS Owner's Guide, sealed in the bag, in the Glove Box. (e) Discard RS3200 Plus Owners Guide, and Warranty Card. (f) Install the Short Pin. (Fig. 6-2)
Fig. 6-1
Install Short Pin
Fig. 6-2
Issue: A
12/18/06
Page 10 of 14 pages
TOYOTA
Check:
TUNDRA
2007 Look For:
TVIP V2
Checklist - these points MUST be checked to ensure a quality installation.
GLASS BREAKAGE SENSOR (GBS)
Accessory Function Checks Roll up all windows, and exit the vehicle with remote. Press and release the remote control’s lock button to start the system’s arming process. 1. The turn signal lights flash once. All doors lock. The security LED lights up. Wait 30 seconds. 2. After 30 seconds the LED starts flashing; the system is now armed. Perform the following check in a temperature- controlled environment (50º-90º F) With the tip of a key, or Striker Tool pulled all the way out (PPO only), tap the center of the driver’s door window to trigger the alarm. 3. The horn sounds repeatedly. The headlights flash repeatedly. The turn signal lights flash repeatedly. The LED lights up. NOTE: If the alarm does not trigger during functional verifications, increase the GBS sensitivity to the next setting.
For all vehicles, press the unlock button of the remote key to stop the alarm. NOTE: If you do not disarm the system, the alarm will last 20 seconds. It is not necessary to check the alarm duration.
4. The horn stops sounding. All the lights stop flashing and/ or turn off. The security LED turns off.
Issue: A
12/18/06
Page 11 of 14 pages
TOYOTA
Check:
TUNDRA
2007 Look For:
TVIP V2
Checklist - these points MUST be checked to ensure a quality installation.
GLASS BREAKAGE SENSOR (GBS)
Vehicle Function Checks Head Lights High Beams Turn Signal Lights Tail Lights Stop Lights Backup Lights Hazard Lights Marker Lights Dome/Courtesy Lights Panel/Switch Illumination Accessory Controls/Illumination (if equipped) Key Sensor Buzzer Fog Lights (if equipped) Daytime Running Lights (if equipped) Trunk/Tailgate/Bed Lights (if equipped) Glove Box Light (if equipped) Cruise Control Light (if equipped) Functioning Key Sensor Functioning Fog Lights Functioning DR Lights Functioning Lights Functioning Glove Box Light Functioning Cruise Control Light Functioning Head Lights Functioning High Beams Functioning Turn Signal Lights Functioning Tail Lights Functioning Stop Lights Functioning Backup Lights Functioning Hazard Lights Functioning Marker Lights Functioning Dome/Courtesy Lights Functioning Controls/Illumination Functioning Accessory
Issue: A
12/18/06
Page 12 of 14 pages
TOYOTA
Check:
TUNDRA
2007 Look For:
TVIP V2
Checklist - these points MUST be checked to ensure a quality installation.
GLASS BREAKAGE SENSOR (GBS) Functioning Seatbelt Warning Light. If the warning light remains "ON", it may indicate a system malfunction.
Seat Belt Warning Light
Air Bag Warning Light
Functioning Air Bag Warning Light. If the warning light remains "ON," it may indicate a system malfunction.
ABS Light (if equipped)
Functioning ABS Light. If the warning light remains "ON,” it may indicate a system malfunction.
Lamp Failure Sensor (if equipped)
Functioning Lamp Failure Light. If the warning light remains “ON,” it may indicate a system malfunction.
Track/Skid Control Light (if equipped)
Functional Track/VSC Light. If the warning light remains “ON,” it may indicate a system malfunction.
HVAC Power Locks (if equipped) Power Windows (if equipped) Power Seats (if equipped) Power Sunroof (if equipped) Horn Gauges Front Wiper/Washer Rear Wiper/Washer (if equipped) Clock (if equipped)
All HVAC Controls Function Functioning Power Locks Functioning Power Windows Functioning Power Seats Functioning Sunroof Functioning Horn Functioning Gauges Functioning Front Wiper/Washer Functioning Rear Wiper/Washer Functioning Clock
Issue: A
12/18/06
Page 13 of 14 pages
TOYOTA
Check:
TUNDRA
2007 Look For: Functioning Power Socket Functioning Starter Functioning Audio/Video Functioning Power Sliding Door Functioning Memory Settings
TVIP V2
Checklist - these points MUST be checked to ensure a quality installation.
GLASS BREAKAGE SENSOR (GBS)
Accessory Power Socket (if equipped) Starter Audio/Video (if equipped) Power Sliding Door (if equipped) Convenience Memory Settings (if equipped) Heated Seats (if equipped) Massage Seats (if equipped) Rear Window Defogger (if equipped) Power Side Mirrors (if equipped) Side Mirror Defogger (if equipped) Front Windshield Defogger (if equipped) Navigation System (if equipped) Power Back Door (if equipped) Steering Wheel Column Adjust
Functioning Heated Seats Functioning Massage Seats Functioning Rear Window Defogger Functioning Power Side Mirrors Functioning Side Mirror Defogger Functioning Front Windshield Defogger Functioning Navigation System Functioning Power Back Door Steering Wheel Column Adjusts Without Interference
Hood Latch Release Passenger Air Bag Switch (if equipped) Rollover Side Curtain Air Bag (RSCA) Switch (if equipped) Remove the Short Pin fuse after the checks are completed.
Functioning Hood Latch Release Functioning Passenger Air Bag Switch Functioning RSCA Switch
Store Short Pin Here
Issue: A
12/18/06
Page 14 of 14 pages
2007 -
TUNDRA
TVIP V5
RS3200 PLUS OWNER’S GUIDE
RS3200 PLUS
SECURITY SYSTEM DESIGNED FOR USE WITH YOUR VEHICLE’S REMOTE KEYLESS ENTRY SYSTEM
OWNER’S GUIDE
Rev. A 06/20/05
TOYOTA RS3200 PLUS Security system
Page 1
To better understand the features and functions of this security system, please read this Owner’s Guide completely prior to use.
TABLE OF CONTENTS
DESCRIPTION INTRODUCTION BRIEF DESCRIPTION–RS3200 PLUS FEATURES OPERATION
ARMING THE RS3200 PLUS (except PASSIVE ARMING) DISARMING THE RS3200 PLUS (except PASSIVE DISARMING) PASSIVE (AUTOMATIC) ARMING & DISARMING AUTOMATIC REARMING ARMING SUSPENSION
PAGE
2 3, 4 5 6 7 8 8 9 9 10 10 11 12
IN
ALARM INFORMATION
ALARM TRIGGERS ALARM DESCRIPTIONS STOPPING AN ALARM
GLASS BREAKAGE SENSOR INFORMATION
GLASS BREAKAGE SENSOR CHECK PROCEDURE
PROGRAMMING
PASSIVE (AUTOMATIC) ARMING AND ENTRY DELAY (Not applicable to Highlander and Sienna. Please consult your Toyota Dealer for programming information.)
WARNING and CAUTION INFORMATION IN B C O
13
C
Par lea
Page 2
TOYOTA RS3200 PLUS Security system
INTRODUCTION
Congratulations on your choice of the RS3200 PLUS add-on security system to protect your vehicle! To get the most from the system, we strongly recommend that you read this Owner’s Guide completely to learn all of its features and functions. The RS3200 PLUS provides security through point-of-entry monitoring, glass breakage detection and ignition switch monitoring. While ARMED, the system will be TRIGGERED and sound an ALARM when a door, trunk or hatch is forcibly unlocked or opened*, or when a window is tapped on or broken. During the ALARM, the vehicle’s horn sounds and the headlights, tail lights and front marker or turn signal lights flash. A l s o , the vehicle’s starter is disabled, preventing engine start. In addition to the comprehensive protection, the RS3200 PLUS works in conjunction with your vehicle’s remote keyless entry system, enabling you to ARM and DISARM the security system at the same time the doors are remotely locked and unlocked. In vehicles equipped with a buzzer, it will chirp when the system is REMOTE ARMED and DISARMED. An important note about your system Throughout this guide, there are references to the STATUS MONITOR for this system. Illustrated below, this panel holds the LED indicator (for the system’s operating status) and the GLASS BREAKAGE SENSOR’S microphone. In vehicles equipped with an engine immobilizer system, there is a LED already installed, so the RS3200 PLUS utilizes the vehicle’s engine immobilizer system LED➂ instead and a microphone mounted in a separate location. If your vehicle falls into this category, remember to look at that LED when the information refers to the STATUS MONITOR. If you do not know where the LED is located, refer to your vehicle’s owner’s guide for specific information.
➀➁
➀
* When the system is PASSIVELY (AUTOMATICALLY) ARMED, there is an ENTRY DELAY that will elapse when a door is opened before an ALARM is TRIGGERED.
untos de entrada, detección as esté armado, el sistema se etero sea desasegurado o vez que se dispara la el frente, las luces traseras y del vehículo queda a protección que ofrece el ntrol remoto de entrada sin ridad al mismo tiempo que los ehículos equipados con desarmado a control remoto.
LIGHTS FOR 30 SECONDS (PREARMING) THEN STARTS FLASHING (SYSTEM IS ARMED)
➁
➂
YOUR ENGINE IMMOBILIZER SYSTEM LED MAY LOOK DIFFERENT THAN THE ONE ILLUSTRATED HERE
monitor 1 2 del sistema. (1) (2) ca el estatus de operación del uipados con sistemas de l sistema RS3200 Plus ez en una ubicación distinta. cuando la información se ubicado dicho LED, refiérase
irá un retraso de
IÓN DEL MOTOR DIFERENTE DEL
Plus para la protección de ndamos que por favor lea das sus funciones y
RAMOS AQUÍ. L SISTEMA DE
TOYOTA RS3200 PLUS Security system
**
Page 3
C A
I
I
BRIEF DESCRIPTION–RS3200 PLUS FEATURES
FEATURES
FUNCTIONS
The RS3200 PLUS will ARM 30 seconds after the lock button on the remote REMOTE keyless entry system’s remote control is pressed, and DISARM when the ARMING/DISARMING unlock button is pressed. If your vehicle is equipped with a buzzer that chirps when the lock and unlock buttons on the remote controls are pressed, the buzzer will also chirp when the system is REMOTE ARMED and DISARMED. The RS3200 PLUS will automatically REARM at the same time the AUTOMATIC vehicle’s remote keyless entry system relocks the vehicle’s REARMING doors, if no door is opened within 30 seconds after REMOTE DISARMING. The RS3200 PLUS will ARM 30 seconds after you close the trunk (if KEY open) and lock the vehicle’s doors with the key, and will DISARM when ARMING/DISARMING you unlock a door with the key. While ARMED, the trunk may be opened with the key (or trunk release button ARMED MODE SUSPENSION** on your remote control, if so equipped) without TRIGGERING an ALARM. Once the open trunk is closed, the system ARMS again. The RS3200 PLUS may be programmed to automatically ARM 30 PASSIVE (AUTOMATIC) seconds after the ignition key is removed, the vehicle exited and the ARMING last door and the trunk closed, without the necessity of locking doors. The RS3200 PLUS may be DISARMED with the vehicle’s ignition key PASSIVE DISARMING after it was PASSIVELY ARMED. ADJUSTABLE ENTRY When the RS3200 PLUS has been PASSIVELY ARMED, an ENTRY DELAY DELAY (user-selectable at 0, 15, or 30 seconds) will start when a door is opened before an ALARM is TRIGGERED. When you lock the vehicle with the central lock switch (while a door MANUAL ARMING is open), the RS3200 PLUS will ARM 30 seconds after you close all the doors and the trunk (if open). The RS3200 PLUS may be DISARMED by inserting the key into the IGNITION KEY ignition switch and turning it to “ON.” DISARMING Forcibly unlocking or opening a door or trunk while the RS3200 PLUS POINT-OF-ENTRY is ARMED will TRIGGER an ALARM immediately. (If the system was PASSIVELY PROTECTION ARMED, the ENTRY DELAY must pass after opening a door before the ALARM is TRIGGERED.) The RS3200 PLUS utilizes a microphone (usually mounted in the GLASS BREAKAGE STATUS MONITOR) to sense the noise from tapping on window glass, or SENSOR glass breaking, and TRIGGER the system to sound an ALARM. It is fine tuned to “listen” for this type of noise, and ignore other sounds. WARN AWAY ALARM When the GLASS BREAKAGE SENSOR’S microphone picks up tapping or breaking of window glass, it TRIGGERS a WARN AWAY ALARM; the headlights and tail and marker or turn signal lights flash, and the horn sounds for 20 seconds, but the starter is not disabled. If there is another detection of glass tapping or breaking, or if a door is opened or unlocked without a key, the regular ALARM is TRIGGERED. While ARMED, the RS3200 PLUS monitors the ignition switch. If an attempt is IGNITION SWITCH made to start the vehicle without a key, an ALARM is TRIGGERED. MONITORING
**Starting from 2002 M.Y., Arming Suspension Mode by using the key to unlock the trunk is not applicable to Camry, Solara, and Corolla.
A A S P P T A T E P A ( S A L A A
Page 4
TOYOTA RS3200 PLUS Security system
BRIEF DESCRIPTION–RS3200 PLUS FEATURES
FEATURES
FUNCTIONS
* TRIGGER MEMORY is not available for Corolla / Matrix.
erra los seguros de las ntre levantado y continúa a. urante su ausencia se haya funcionamiento, al ces delanteras y traseras
S DEL SISTEMA
terrumpido mientras el ez restablecida, la alarma
un zumbador que suena istema a control remoto sin bador también sonará do a distancia. lus activa el claxon del
eshabilita el encendido del rrancado hasta que el
Plus monitorea el interruptor arranque del vehículo sin la
as e intermitentes cada vez el sistema y cuando se ás se encienden las luces
rotura de cristales y al LED eración del sistema de el LED del inmobilizador del arado).
atrix.
When an ALARM is TRIGGERED, the system disables the vehicle’s STARTER DISABLE starter and prevents engine start until the system is reset (DISARMED). During an ALARM, the system will lock the doors if one is unlocked, FORCED LOCK and will continue to do so for the duration of the ALARM. DURING ALARM The user is notified that an ALARM occurred. Upon DISARMING the TRIGGER MEMORY * system after an ALARM was TRIGGERED, the vehicle’s tail and marker lights will be turned on for 2 seconds. The RS3200 PLUS flashes the vehicle’s tail and marker or turn signal lights EXTERIOR LIGHT during REMOTE ARMING and REMOTE DISARMING, and during an ALARM. ACTIVATION Also, during an ALARM the headlights flash. If your vehicle is equipped with a buzzer that chirps when the lock BUZZER ACTIVATION and unlock buttons on the remote keyless entry system’s remote controls are pressed, the buzzer will also chirp when the system is REMOTE ARMED and DISARMED. HORN ACTIVATION During an ALARM, the RS3200 PLUS activates the vehicle’s horn. If power to the RS3200 PLUS is disrupted while it is ARMED, an ALARM is POWER LOSS MEMORY TRIGGERED once power is restored. This panel houses the GLASS BREAKAGE SENSOR microphone and the STATUS MONITOR flashing LED that indicates the operating status of the security system. (Some vehicle applications utilize the vehicle’s engine immobilizer system LED and a separate microphone, instead.)
TOYOTA RS3000 PLUS Security system
Page 5
* ∆E El
OPERATION
ARMING THE RS3200 PLUS (except PASSIVE ARMING)
The system may be ARMED in several ways. Do one of the following: Lock the doors with your key: Remove the key from the ignition switch. Exit the vehicle, and close all the doors.* Close the trunk or hatch, if necessary.* Insert the key into the door key switch and turn it toward the front of the vehicle: The STATUS MONITOR’S LED turns on for 30 seconds, then starts flashing.➀ The system is now ARMED. Lock the doors from inside the vehicle: Remove the key from the ignition switch. Open the driver’s or front passenger’s door. Push the central lock switch. Exit the vehicle, and close all the doors.* Close the trunk or hatch, if necessary.* Then: The STATUS MONITOR’S LED turns on for 30 seconds, then starts flashing.➀ The system is now ARMED. Lock the doors with the remote control: Remove the key from the ignition switch. Exit the vehicle, and close all the doors.* Close the trunk or hatch, if necessary.* Press the lock button on the remote control. Simultaneously: The doors lock.➁ The vehicle’s tail and marker or turn signal lights flash once.③ The vehicle’s buzzer chirps once.∆ The STATUS MONITOR’S LED turns on for 30 seconds, then starts flashing.➀ The system is now ARMED.
AR
O
PR DE LA
GIR
PR Q
1
TURN TOWARD THE FRONT OF THE VEHICLE PUSH THE LOCK SWITCH WHILE THE DOOR IS OPEN PRESS AND RELEASE THE LOCK BUTTON
➀
LIGHTS FOR 30 SECONDS (PREARMING) THEN FLASHES (SYSTEM IS ARMED)
➁
③
ALL DOORS LOCK WHEN THE SYSTEM IS REMOTE ARMED
THE TAIL AND MARKER OR TURN SIGNAL LIGHTS FLASH ONCE WHEN THE SYSTEM IS REMOTE ARMED
* The system will not ARM while any of the doors, trunk or hatch is open. ∆ If your vehicle is equipped with a buzzer.
Page 6
TOYOTA RS3200 PLUS Security system
The system may be DISARMED in several ways. Do one of the following: Unlock the doors with your key: Insert the key into the door key switch and turn it toward the rear of the vehicle: The STATUS MONITOR’S LED stops flashing.➀The system is now DISARMED.*
TURN TOWARD THE REAR OF THE VEHICLE
PUSH THE UNLOCK BUTTON
➀
STOPS FLASHING WHEN THE SYSTEM IS DISARMED
➁
➂
* Please note, if the system utilizes your vehicle’s engine immobilizer system LED instead of the STATUS MONITOR, the LED will continue to flash. ∆ If your vehicle is equipped with a buzzer.
IVO)
THE TAIL AND MARKER OR TURN SIGNAL LIGHTS FLASH TWICE WHEN THE SYSTEM IS REMOTE DISARMED
siguientes:
THE DRIVER’S DOOR UNLOCKS WHEN THE SYSTEM IS REMOTE DISARMED
unner, también podrá desde la puerta trasera; ismo tiempo.
NOTE: If your vehicle’s tail and marker or turn signal lights turn on for 2 seconds when the system is DISARMED,* the TRIGGER MEMORY was activated; something TRIGGERED an ALARM while you were away from the vehicle. This feature is not available for Corolla / Matrix.
remoto: tas desde el control remoto.
TURN THE KEY TO “ON” TO DISARM THE SYSTEM
This method of disarming is rarely used. You must be inside the vehicle while the system is armed in order to do it.
3 lo centellearán dos veces. (3) ∆ 1 dejará de parpadear. (1)
Use the ignition switch: Insert the key into the ignition switch, then turn it to ON. The STATUS MONITOR’S LED stops flashing.➀The system is now DISARMED.*
: , después gírela a la posición
tas nuevamente dentro de ber desasegurado la puerta las puertas.
usado. Usted deberá se encuentre armado
y gírela hacia la parte trasera
1 dejará de parpadear. (1)
Unlock the doors with the remote control: Press the unlock button on the remote control. Simultaneously: The driver’s door unlocks.➁ The vehicle’s tail and marker or turn signal lights flash twice.➂ The vehicle’s buzzer chirps twice.∆ The STATUS MONITOR’S LED stops flashing.➀The system is now DISARMED.* Press the unlock button again within 3 seconds after unlocking the driver’s door to unlock the remaining doors.
segundos al desarmar el go hizo sonar la alarma
In the case of Highlander, Sienna, and 4Runner, you may also disarm the system using the key in the back door; all doors will unlock at the same time.
ERAS E INTERMITENTES PARPADEAN DOS
SARMAR REMOTAMENTE AL SISTEMA
DISARMING THE RS3200 PLUS (except PASSIVE DISARMING)
del vehículo para rpadeando.
1 a dejará de parpadear. (1)
OPERATION
TOYOTA RS3200 PLUS Security system
Page 7
Ta NO
EL
SEG
DO L
EN
*S do so su C de ha ab de 15 po la
OPERATION
PASSIVE (AUTOMATIC) ARMING & DISARMING
When the RS3200 PLUS is programmed to PASSIVELY ARM, the system will ARM after the ignition key is removed and all doors and the trunk are closed; you do not need to lock the doors. When you come back to your vehicle and open a door, you must insert the key into the ignition switch and turn it to “ON” during the ENTRY DELAY (0, 15 or 30 seconds), or an ALARM will be TRIGGERED. If you lock the doors, regular ARMING will override PASSIVE ARMING; there will be no ENTRY DELAY. See the PROGRAMMING information on page 13 to activate the PASSIVE ARMING mode, as well as to select the ENTRY DELAY time. (Not applicable to Highlander and Sienna. Please consult your Toyota Dealer for programming information .) To PASSIVELY ARM the system: Remove the key from the ignition switch. Exit the vehicle, and close all the doors. (The system will not ARM while any of the doors are open.) Close the trunk or hatch, if necessary. (The system will not ARM while the trunk or hatch is open.) After the last door, trunk or hatch is closed: The STATUS MONITOR’S LED turns on for 30 seconds, then starts flashing.➀The system is now ARMED.
A
O
1
E
THE SYSTEM ARMS 30 SECONDS AFTER THE LAST ENTRY POINT (DOOR, TRUNK OR HATCH) IS CLOSED
THE SYSTEM DISARMS WHEN YOU INSERT THE KEY AND TURN IT TO “ON”
To DISARM the PASSIVELY ARMED system: Enter the vehicle through a front door. The ENTRY DELAY begins: The STATUS MONITOR’S LED turns on (no flashing.)➁ Insert the key into the ignition switch and turn it to “ON” before the ENTRY DELAY ends.* The LED turns off. The system is now DISARMED. You may also DISARM the system following any of the methods described on page 6.
NOTE: If your vehicle’s tail and marker lights turn on for 2 seconds when the ignition key is turned to “ON”, the TRIGGER MEMORY was activated; something TRIGGERED an ALARM while you were away from the vehicle. This feature is not available for Corolla/Matrix. ➀
LIGHTS FOR 30 SECONDS (PRE-ARMING) THEN STARTS FLASHING (SYSTEM IS ARMED)
➁
TURNS ON (NO FLASHING) DURING THE ENTRY DELAY
* If the ENTRY DELAY time elapses before the ignition switch is turned to “ON”, an ALARM will be TRIGGERED. To DISARM the system during an ALARM, insert the ignition key and turn it to “ON”, or press and release the remote control’s unlock button.
Page 8
TOYOTA RS3200 PLUS Security system
OPERATION
AUTOMATIC REARMING
When you unlock the doors using the remote control, the RS3200 PLUS is DISARMED at the same time. However, if you do not open a door or the trunk within 30 seconds, the keyless entry system will relock the doors and the RS3200 PLUS will REARM 30 seconds later. How the RS3200 PLUS automatically REARMS:
0
45
15
30
THE DOORS ARE UNLOCKED BY PRESSING THE UNLOCK BUTTON ON THE REMOTE CONTROL...
WHEN NO DOOR, TRUNK OR HATCH IS OPENED...
FOR MORE THAN 30 SECONDS...
The ARMED state of the RS3200 PLUS can be suspended temporarily by using the key to unlock and open the trunk. If your remote control is so equipped, you may also suspend the ARMED state using the trunk release button➀to open the trunk. When the ARMING is suspended, the STATUS MONITOR’S LED will turn off ➁until the trunk is closed again. ➀ ➁
TURNS OFF WHEN THE ARMED STATE IS SUSPENDED
OPENING THE TRUNK SUSPENDS THE ARMED STATE OF THE SECURITY SYSTEM
RS3200 Plus se desarmará al o dentro de los 30 segundos 30 segundos más tarde se
E ENTRADA SIN MÁTICAMENTE
EL LED
SE ENCENDERÁ
**Starting from 2002 M.Y., Arming Suspension Mode by using the key to unlock the trunk is not applicable to Camry, Solara, and Corolla.
lmente al emplear la llave to tenga la función para otón para abrir el maletero a e monitorea el condición se
ARMING SUSPENSION**
THE KEYLESS THE LED WILL ENTRY LIGHT UP FOR 30 SYSTEM AUTOMATSECONDS ICALLY RELOCKS (PRE-ARM), THEN THE DOORS, THEN FLASH WHEN THE THE RS3200 PLUS SYSTEM IS ARMED AUTOMATICALLY REARMS.
los automóviles modelo tado de suspensión del abrir el maletero no estará para el Camry, Solara y
AS PUERTAS, Y TEMA RS3200 TICAMENTE SE RMA POR 30 SEGUNDOS (PRE-ARMADO) Y LUEGO PARPADEARÁ CUANDO EL SISTEMA ESTÉ ARMADO
TOYOTA RS3200 PLUS Security system
Page 9
ALARM INFORMATION
ALARM TRIGGERS
While the system is ARMED, an ALARM will be TRIGGERED when any of the following occurs:
➤
Forcibly opening a door, or the trunk or hatch without a key Pulling the trunk release lever inside the vehicle will also TRIGGER an ALARM.
➤
Manually unlocking a door Manually operating an inside lock button will TRIGGER an ALARM. Note: Because this action will TRIGGER an ALARM, it is important that you do not ARM the system while someone is in the vehicle.
➤
“Hot wiring” the vehicle The RS3200 PLUS can detect the absence of the ignition key if the ignition circuit is shorted in attempt to start the vehicle.
➤
Tapping on or breaking the glass The noise from tapping on, or breaking of glass TRIGGERS a WARN AWAY ALARM first, then a regular ALARM. See the description of how the GLASS BREAKAGE SENSOR TRIGGERS ALARMS on page 12.
➤
Mie las
Power restoration If power to the system is interrupted while it is ARMED, an ALARM will be TRIGGERED immediately when power is restored.
CO
IN
Page 10
TOYOTA RS3000 PLUS Security system
ALARM DESCRIPTIONS
Regular ALARM ➀ When an ALARM is triggered in any way other than initial detection by the GLASS BREAKAGE SENSOR, the following occur: The horn sounds repeatedly for 60 seconds. The headlights flash repeatedly for 60 seconds. The tail and marker or turn signal lights flash repeatedly for 60 seconds. The starter is disabled (no engine start) until the system is DISARMED. The door lock will be relocked if someone reaches in and unlocks the inside lock button. After 60 seconds of ALARM, the system will REARM and continue to protect the vehicle.
➀
THE HORN SOUNDS FOR 60 SECONDS
THE STARTER IS DISABLED UNTIL THE SYSTEM IS DISARMED MARKER OR TURN SIGNAL LIGHTS FLASH FOR 60 SECONDS
TAIL OR TURN SIGNAL LIGHTS FLASH FOR 60 SECONDS
WARN-AWAY ALARM ➁ Upon initial detection of noise from tapping on, or breaking glass, the GLASS BREAKAGE SENSOR TRIGGERS a WARN AWAY ALARM: The horn sounds repeatedly for 20 seconds. The headlights flash repeatedly for 20 seconds. The tail and marker or turn signal lights flash repeatedly for 20 seconds. If the GLASS BREAKAGE SENSOR detects noise again, or if a door or trunk is opened while the system is still ARMED, the regular ALARM (described above) is activated.
➁
THE HORN SOUNDS FOR 20 SECONDS TAIL OR TURN SIGNAL LIGHTS FLASH FOR 20 SECONDS
Simply DISARM the system using the remote control or key as described on page 6.
rimera señal de advertencia
STOPPING AN ALARM
segundos. undos. á ser arrancado el motor)
HEADLIGHTS FLASH FOR 20 SECONDS MARKER OR TURN SIGNAL LIGHTS FLASH FOR 20 SECONDS
ndo con la protección del
lguien los abriera
o romper algún cristal, el
HEAD LIGHTS FLASH FOR 60 SECONDS
segundos. undos. evamente, o si alguna puerta larma regular (descrita
ve, como se describió en la
TRASERAS Y LAS INTERMITENTES
ALARM INFORMATION
LAS
Y LAS INTERMITENTES PARPADEARÁN POR 60 SEGUNDOS
PARPADEARÁN DURANTE 20 SEGUNDOS
LAS
LUCES TRASERAS
LUCES
TOYOTA RS3200 PLUS Security system
Page 11
GLASS BREAKAGE SENSOR INFORMATION
The RS3200 PLUS provides protection for your vehicle above and beyond entry point monitoring–it “listens” for the noise made by tapping on, or breaking of glass. Using a microphone designed specifically for this task, the GLASS BREAKAGE SENSOR is capable of ignoring other noises, which helps to prevent “false alarms” from occurring.
GLASS BREAKAGE SENSOR CHECK PROCEDURE
When the RS3200 PLUS was installed in your vehicle, care was taken to adjust the sensitivity level of the GLASS BREAKAGE SENSOR. You may observe how it works following the procedure listed below. 1. ARM the system. Press the lock button on the remote control or lock the doors with the key. (Remember, the system will not ARM if any door, the trunk or hatch is open.)
2.
Wait until the STATUS MONITOR’S LED starts flashing. The LED will flash 30 seconds after the last door, the trunk or hatch is closed.
3.
With the tip of a key, tap the center of the driver’s door window. Tap the glass with light to moderate force. WARNING: Do not hit the glass with excessive force, especially in cold weather, or you may crack or break it.
Cu cris pro
A WARN AWAY ALARM should be TRIGGERED. If the ALARM is not TRIGGERED, make sure you performed the procedure correctly and try again. If you find that the system did not perform as expected, contact your Toyota dealer for more information. 4. DISARM the system to stop the WARN AWAY ALARM. Press the unlock button on the remote control or use the key to DISARM the system.
P C
El ést un cris
IN
Page 12
TOYOTA RS3200 PLUS Security system
PROGRAMMING
. El sistema desasegurará la puerta en dos segundos; si esto no sucede, empiece nuevamente. El proceso de programación ha terminado. e pasivamente. Para cambiar áticamente), así como para uación. Para mayor o se aplica para el mación acerca de la prograetire la llave del cilindro de veces; este procedimiento pletar en el espacio de cinco pacio de 40 segundos.) re el seguro la puerta del ductor. cierre la d. Asegure y despus desasegure tres del veces el seguro tor. interno de la puerta del conductor. pasos en menos de 40 de programación. PASIVO. SELECCIÓN DEL The RS3200 PLUS is factory-set to not PASSIVELY ARM. To change the system’s operation for PASSIVE ARMING operation, as well as adjust the ENTRY DELAY time, follow the procedure below. For more information on this feature, please refer to page 7. (Not applicable to Highlander and Sienna. Please consult your Toyota Dealer for programming information.)
PASSIVE ARMING ON/OFF SELECTION, ENTRY DELAY TIME SELECTION
1. Before you begin: 2. Open the driver’s door. Close the remaining doors and the trunk or hatch. Unlock all doors with the inside lock switch. Remove the key from the ignition switch. Insert and remove the key from the ignition key cylinder 3 times; this must be completed within 5 seconds.
Start the Programming Procedure. (Complete these steps within 40 seconds.)
a. Close the driver’s door.
b. Lock and unlock all doors 3 times by key or remote control.
c. Open and close d. Lock, then unlock the driver’s door the driver’s door. inside lock button 3 times.
e. Open the driver’s door.
f.
The system locks the door in 2 seconds; if this does not happen, start over.
g. Unlock the driver’s door knob.
3. Select the Operating Mode and Complete the Programming Procedure.
a. Close, then Open the driver’s door: b. Lock then unlock the c. The system locks the 2 times = PASSIVE ARMING OFF driver’s door inside lock door in 2 seconds; if this 3 times = PASSIVE ARMING ON, does not happen, start button 1 time. 0 Sec. ENTRY DELAY over. Programming is now 4 times = PASSIVE ARMING ON, complete. 15 Sec. ENTRY DELAY 5 times = PASSIVE ARMING ON, 30 Sec. ENTRY DELAY
TOYOTA RS3200 PLUS Security system
Page 13
Warning
• • • •
This product is applicable only to vehicles with 12V DC, negative grounding specifications. Do not use in vehicles with 24V specifications. Otherwise, damage to the unit or a fire may result. Never attempt to disassemble or modify the product. Otherwise, an accident, fire or electric shock may result. When replacing fuses, be sure to use fuses with the same specified capacity (amperage.) Otherwise, damage to the unit or vehicle, fire or electric shock may result. If an abnormal condition occurs, such as liquids spilling onto the product, or the product emitting smoke or strange odors, stop using it immediately and consult the dealer from whom you purchased the product. Continued use of the product before corrective actions are taken may result in an accident, injury or fire. Never pull the plastic bag over your head. Otherwise, a serious injury or death from suffocation may occur.
•
• • • • • • •
Caution
• •
Do not use this product for applications other than in-vehicle use. Otherwise, an electric shock or injury may result. Do not allow children to play with the remote controls. Otherwise, the doors may be locked or unlocked, the security system armed or disarmed, or an alarm triggered unintentionally. If this product is dropped or its case is damaged, disconnect the power supply lead and contact the dealer from whom you purchased it to obtain service. Otherwise, a fire or electric shock may result.
• l l i
•
090002-28940700
02-28940700
