BS EN 12350-4

Published on June 2016 | Categories: Types, Government & Politics | Downloads: 87 | Comments: 0 | Views: 679
of 9
Download PDF   Embed   Report

This European standard specifies a method for determining the consistency of fresh concrete by determining the degree of compactability. It is not applicable to concrete of which the maximum size of aggregate exceeds 63 mm. If the degree of compactability is less than 1,04 ormore than 1,46, the concrete has a consistency for which the degree of compactability test is not suitable.

Comments

Content

British Standard

Licensed Copy: KBR Halliburton, Kellogg Brown & Root, 10 June 2004, Uncontrolled Copy, (c) BSI

A single copy of this British Standard is licensed to
KBR Halliburton

10 June 2004

This is an uncontrolled copy. Ensure use of the most current version of this document by searching British Standards Online at bsonline.techindex.co.uk

BRITISH STANDARD

Testing fresh concrete Ð
Part 4: Degree of compactability

Licensed Copy: KBR Halliburton, Kellogg Brown & Root, 10 June 2004, Uncontrolled Copy, (c) BSI

The European Standard EN 12350-4:1999 has the status of a British Standard

ICS 91.100.30

NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW

| BS EN | | | 12350-4:2000 | | | | Incorporating | | Corrigendum No. 1 | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |

BS EN 12350-4:2000

National foreword
This British Standard is the English language version of EN 12350-4:1999. It will supersede BS 1881-103:1993 which will be withdrawn in 2003 when the full package of concrete standards is available. The UK participation in its preparation was entrusted by Technical Committee B/517, Concrete, to Subcommittee B/517/1, Concrete production and testing, which has the responsibility to: Ð aid enquirers to understand the text; Ð present to the responsible European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; Ð monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this subcommittee can be obtained on request to its secretary.

Licensed Copy: KBR Halliburton, Kellogg Brown & Root, 10 June 2004, Uncontrolled Copy, (c) BSI

Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled ªInternational Standards Correspondence Indexº, or by using the ªFindº facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations.

Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 4, an inside back cover and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued.

This British Standard, having been prepared under the direction of the Sector Committee for Building and Civil Engineering, was published under the authority of the Standards Committee and comes into effect on 15 January 2000 © BSI 09-2000

Amendments issued since publication Amd. No. Date Comments National foreword supersession details updated

11082 September Corrigendum No.1 2000

ISBN 0 580 35298 6

EUROPEAN STANDARD Â ENNE NORME EUROPE È ISCHE NORM EUROPA

EN 12350-4
October 1999

ICS 91.100.30

English version

Testing fresh concrete Ð Part 4: Degree of compactability

Licensed Copy: KBR Halliburton, Kellogg Brown & Root, 10 June 2004, Uncontrolled Copy, (c) BSI

Essai pour be Âton frais Ð Partie 4: Degre  de compactabilitie Â

Pru È fung von Frischbeton Ð Teil 4: Verdichtungsmaû

This European Standard was approved by CEN on 5 September 1999. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.

CEN
European Committee for Standardization Comite  Europe Âen de Normalisation Europa Èisches Komitee fu È r Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels © 1999 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12350-4:1999 E

Page 2 EN 12350-4:1999

Foreword
This European Standard has been prepared by Technical Committee CEN/TC 104, Concrete (performance, production, placing and compliance criteria), the Secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2000, and conflicting national standards shall be withdrawn at the latest by December 2003. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. This standard is one of a series concerned with testing fresh concrete. It is based on the International Standard ISO 4111: Fresh Concrete Ð Determination of the consistency Ð Degree of compactability (Compaction Index). A draft for this standard was published in 1996 for CEN enquriy as prEN 12357. It was one of a series of individually numbered test methods for fresh or hardened concrete. For convenience it has now been decided to combine these separate draft standards into three new standards with separate parts for each methods, as follows: Ð Testing fresh concrete (EN 12350:1999); Ð Testing hardened concrete (prEN 12390:1999); Ð Testing concrete in structures (prEN 12504:1999). This series EN 12350 includes the following parts where the brackets give the numbers under which particular test methods were published for CEN enquiry: EN 12350: Testing fresh concrete Part 1: Sampling (former prEN 12378:1996). Part 2: Slump test (former prEN 12382:1996). Part 3: Vebe test (former prEN 12350:1996). Part 4: Degree of compactability (former prEN 12357:1996). Part 5: Flow table test (former prEN 12358:1996). Part 6: Density (former prEN 12383:1996). Part 7: Air content Ð Pressure methods (former prEN 12395:1996). CAUTION. When cement is mixed with water, alkali is released. Take precautions to avoid dry cement entering the eyes, mouth and nose whilst mixing concrete. Prevent skin contact with wet cement or concrete by wearing suitable protective clothing. If cement or concrete enters the eye, immediately wash it out thoroughly with clean water and seek medical treatment without delay. Wash wet concrete off the skin immediately.

Contents
Foreword 1 Scope 2 Normative references 3 Principle 4 Apparatus 5 Sampling 6 Procedure 7 Expression of results 8 Test report 9 Precision Page 2 3 3 3 3 4 4 4 4 4

Licensed Copy: KBR Halliburton, Kellogg Brown & Root, 10 June 2004, Uncontrolled Copy, (c) BSI

© BSI 01-2000

Page 3 EN 12350-4:1999

1 Scope
This European standard specifies a method for determining the consistency of fresh concrete by determining the degree of compactability. It is not applicable to concrete of which the maximum size of aggregate exceeds 63 mm. If the degree of compactability is less than 1,04 or more than 1,46, the concrete has a consistency for which the degree of compactability test is not suitable.

4.2 Trowel, with a flat blade (see Figure 1).
Dimensions in millimeters

2 Normative references
This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. EN 12350-1:1999, Testing fresh concrete Ð Part 1: Sampling. Figure 1 Ð Trowel

Licensed Copy: KBR Halliburton, Kellogg Brown & Root, 10 June 2004, Uncontrolled Copy, (c) BSI

3 Principle
Fresh concrete is carefully placed in a container, avoiding any compaction whilst filling, using a trowel. When the container is full, the top surface is struck off level with the top of the container. The concrete is compacted by vibration and the distance from the surface of the compacted concrete to the upper edge of the container is used to determine the degree of compactability. 4.3 Means of compacting the concrete, which shall be one of the following: Ð internal vibrator: with a minimum frequency of approximately 120 Hz (7 200 cycles per minute). The diameter of the internal vibrator shall not exceed one-quarter of the smallest dimension of the container; Ð vibrating table: with a minimum frequency of approximately 40 Hz (2 400 cycles per second). The use of a vibrating table shall be the reference method. 4.4 Remixing container, flat tray of rigid construction and made from a non-absorbent material not readily attacked by cement paste. It shall be of appropriate dimensions such that the concrete can be thoroughly re-mixed, using the square-mouthed shovel. 4.5 Shovel, with square mouth.
NOTE The square mouth is required to ensure proper mixing of material on the remixing container.

4 Apparatus
4.1 Container, made of metal not readily attacked by cement paste. The internal dimensions of the container shall be: Ð base: (200 ± 2) mm 3 (200 ± 2) mm; Ð height: 400 mm ± 2 mm. The thickness of the base and walls shall be at least 1,5 mm.
NOTE The bottom of the container may be perforated to facilitate emptying. A suitable plastic plate to cover the bottom has then to be placed inside the container.

4.6 Straight edged scraper, more than 200 mm in length 4.7 Rule. 4.8 Moist cloth.

© BSI 01-2000

Page 4 EN 12350-4:1999

5 Sampling
The sample shall be obtained in accordance with EN 12350-1:1999. The sample shall be re-mixed before carrying out the test.

7 Expression of results
The degree of compactability c is given by the formula: h1 c= h1 2 s where h1 is the internal height of the container, in millimetres; s is the mean value, to the nearest millimetres, of the four distances from the surface of the compacted concrete to the upper edges of the container. The result shall be reported to two decimal places.

6 Procedure
Clean the container and moisten the inner surfaces using a damp cloth. Fill the container, without tamping it, by tilting the trowel sideways from all four upper edges of the container in turn. When the container is filled, remove all concrete above the upper edges, using the straight edged scraper with a sawing action, in such a way as to avoid any compacting effect. Compact the concrete by means of a vibrating table or by the use of an internal vibrator, until no further reduction in volume is determinable. During compaction avoid loss of concrete through splashing, or leakage.
NOTE 1 Great care is recommended if loss of entrained air is to be avoided when using an internal vibrator.

8 Test report
The report shall include: a) identification of the test sample; b) location of performance of test; c) date of test; d) determined degree of compactability, to two decimal places; e) any deviation from standard test method; f) declaration by the person technically responsible for the test that it was carded out in accordance with this standard, except as noted in item e). The report can include: g) time of test; h) temperature of the concrete sample at time of test.

Licensed Copy: KBR Halliburton, Kellogg Brown & Root, 10 June 2004, Uncontrolled Copy, (c) BSI

After compaction, determine the value of s (see Figure 2), i.e: the mean value of the distance between the surface of the compacted concrete and the upper edge of the container to the nearest millimetre. Obtain this value by measuring at the middle of each side of the container.
NOTE 2 The consistence of a concrete mix changes with time, due to hydration of the cement and, possibly, loss of moisture. Tests on different samples should, therefore, be carded out at a constant time interval after mixing, if strictly comparable results are to be obtained.

9 Precision
There is currently no precision data for this test.
Dimensions in millimeters

Figure 2 Ð Concrete in container, before and after compaction

© BSI 01-2000

Licensed Copy: KBR Halliburton, Kellogg Brown & Root, 10 June 2004, Uncontrolled Copy, (c) BSI

blank

BS EN 12350-4:2000

Licensed Copy: KBR Halliburton, Kellogg Brown & Root, 10 June 2004, Uncontrolled Copy, (c) BSI

BSI 389 Chiswick High Road London W4 4AL

| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |

BSI Ð British Standards Institution
BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means ± electronic, photocopying, recording or otherwise ± without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.

Sponsor Documents

Or use your account on DocShare.tips

Hide

Forgot your password?

Or register your new account on DocShare.tips

Hide

Lost your password? Please enter your email address. You will receive a link to create a new password.

Back to log-in

Close