IRJET-RF Energy Harvesting from Cell Phone in GSM900 Band

Published on December 2016 | Categories: Documents | Downloads: 59 | Comments: 0 | Views: 206
of 5
Download PDF   Embed   Report

In this paper an experimental RF energy harvesting system using rectifying antenna (rectenna) to harvest ambient energy from cell phones operating at 900 MHz GSM band is presented. The proposed circuit is a combination of RMPA and rectifying circuit using Schottky diode for microwave (RF) to DC conversion. The performance of the rectenna is simulated by electromagnetic simulator Computer Simulation Technology (CST) Microwave Studio. Rectenna offers maximum radiation efficiency of around 55.61%, gain of 3.4 dBi and directivity of 5.972 dBi. The proposed rectenna design can prove to be a low cost device for wireless power transmission and RF energy harvesting. GSM 900 band is used as this is the most commonly used band for mobile communications. This rectenna offers return loss of 17 dB at frequency of around 900 MHz.

Comments

Content

International Research Journal of Engineering and Technology (IRJET)

e-ISSN: 2395 -0056

Volume: 02 Issue: 04 | July-2015

p-ISSN: 2395-0072

www.irjet.net

RF Energy Harvesting from Cell Phone in
GSM900 Band
B.Hridayeta1, P.K.Singhal2
1, 2

Department of Electronics, Madhav Institute of Technology and Science, Gwalior-474005

---------------------------------------------------------------------***---------------------------------------------------------------------

Abstract - In this paper an experimental RF energy
harvesting system using rectifying antenna (rectenna)
to harvest ambient energy from cell phones operating
at 900 MHz GSM band is presented. The proposed circuit
is a combination of RMPA and rectifying circuit using
Schottky diode for microwave (RF) to DC conversion.
The performance of the rectenna is simulated by
electromagnetic simulator Computer Simulation
Technology (CST) Microwave Studio. Rectenna offers
maximum radiation efficiency of around 55.61%, gain
of 3.4 dBi and directivity of 5.972 dBi. The proposed
rectenna design can prove to be a low cost device for
wireless power transmission and RF energy harvesting.
GSM 900 band is used as this is the most commonly used
band for mobile communications. This rectenna offers
return loss of 17 dB at frequency of around 900 MHz.

Key Words: Rectangular Microstrip Patch Antenna
(RMPA), Rectenna, Radio Frequency (RF), Computer
simulation Technology (CST-MW), Global System for
Mobile Communication (GSM).

Rectenna is needed for efficient utilization of wireless
power. This RF power is basically “free” source of energy.
The number of radio transmitters, specifically base
stations, and cell phones are continuously increasing. WiFi routers, laptops are also source of radio energy.
Consider the case, for example, inside a single room, it is
possible to collect a small measure of vitality from an
average Wi-fi switch transmitting at a force level of 50 to
100 mw [3]. Basic feature of portable devices are small
dimensions, so the rectenna should be as small as possible
[4]. Received power is low for small sized rectenna. Thus
wireless power transfer is most suitable for low-power
applications for instance a low-power wireless sensor.
For testing the designed rectenna, total efficiency and
conversion efficiency are given by equation (1) and (2),
[5].
The total efficiency

(1)

1. INTRODUCTION
Recent years have seen increasing use of wireless devices
in many applications like cell phones, sensor networks and
other low power devices. RF energy is continuously
radiated from several sources which include Mobile
phones (869-890 MHz in CDMA, 935-960 MHz in GSM 900
band and 1810-1880 MHz in GSM 1800 bands), FM radio
system ( 88-108 MHz ), Cell Tower Transmission (10-20
W per carrier ), Wi-Fi (2.45 GHz, 5.8 GHz), TV transmission
(180-220 MHz ), AM Transmission ( 540-1600 KHz ) etc
[1].
This ambient energy present around us can be harvested
using a rectifying antenna, popularly known as rectenna. A
rectenna comprises of antenna along with the rectifying
circuit. The antenna receives the RF energy and the
rectifying circuit converts it to DC electrical power [2].

© 2015, IRJET.NET- All Rights Reserved

Conversion efficiency is given by

ηc =

(2)

To design the rectenna, CST Microwave Studio software [6] is
used. Computer Simulation Technology (CST) Microwave
Studio is a software package that is fully featured.
Electromagnetic analysis and design in high frequency range
can be done using CST. The software comprises of four
different simulation techniques (transient solver, frequency
domain solver, Eigen mode solver, modal analysis solver).
The most versatile and flexible is the transient solver tool,
which can obtain the broadband frequency behaviour of the
simulated device. The properties of the antenna such as

Page 420

International Research Journal of Engineering and Technology (IRJET)

e-ISSN: 2395 -0056

Volume: 02 Issue: 04 | July-2015

p-ISSN: 2395-0072

www.irjet.net

reflection coefficient S11 and Gain are determined with the
help of CST Software.
The proposed rectenna design consists of RMPA and
a half wave rectifier circuit.

Table -1: Parameters and Design Specifications of
Antenna
S No.

Antenna Parameters

Values

1.

Resonating Frequency

900 MHz

2.

Dielectric Constant(relative)

4.3

3.

Substrate Thickness

1.6 mm

4.

Loss Tangent

0.02

Table -2: Calculated dimensions of Patch Antenna
Fig -1: Basic Rectenna block diagram

2. METHODOLOGY

S No.
1
2

Antenna Parameters
Patch width
Patch height

Values in mm
86
80

2.1 Antenna Design and Fabrication
Fig.2. shows the basic rectangular patch antenna The
reflection coefficient, radiation pattern, gain, directivity
and VSWR are found by simulating the antenna on CST
and measured by spectrum analyzer.
The front view of the proposed rectenna is shown in Fig. 4.
It consists of a rectangular microstrip patch antenna
operating at resonant frequency of 900 MHz with 50Ω
microstrip line feed. The rectenna is printed on a FR4epoxy substrate having relative dielectric constant εr =4.3
and thickness h=1.6 mm.
In the fabrication and designing process of rectenna
initially we design the RMPA at desired frequency of 900
MHz. Fig. 3 shows the designed patch antenna on CST at
900 MHz.

Fig -3: CST view of Rectangular Microstrip Patch Antenna

2.2 Rectifier Designing
A rectifier is a device that converts bidirectional
alternating current (AC) to unidirectional direct current
(DC).The process is known as rectification. A basic half
wave rectifier is considered in this paper. Fig. 4 shows a
half wave rectifier circuit used in this design.

Fig -2: Rectangular Microstrip Patch Antenna
© 2015, IRJET.NET- All Rights Reserved

Fig -4: Rectifier circuit

Page 421

International Research Journal of Engineering and Technology (IRJET)

e-ISSN: 2395 -0056

Volume: 02 Issue: 04 | July-2015

p-ISSN: 2395-0072

www.irjet.net

In this circuit we have used a capacitor of 10 pF, a schottky
diode and a resistor of 1 KΩ. Instead of a semiconductor–
semiconductor junction, Schottky diode use a metalsemiconductor junction thus allowing the junction to
operate at a much faster rate. It gives a forward voltage
drop of as low as 0.15 V.
In the proposed rectifier circuit, HSMS 282C Schottky
Diode is used. Avago’s HSMS-282x family of zero bias
Schottky detector diodes has been designed and optimized
for use in small signal. They are ideal for RF Tag and RFID
applications where primary (DC bias) power is not
available [7].
A linearly polarized microstrip patch antenna (86 mm x 80
mm) has been associated with the rectifier to obtain the
complete rectenna. The antenna simulation was carried
out using the electromagnetic simulator CST v.10 [6]. The
antenna has been achieved and measured in a first time. A
good input matching level is seen at 900MHz.
Fig.5 below shows the final design of integrated rectenna
in CST software which is now ready for final simulation.
Fig.6 shows the back view of the rectenna where the
ground has been defected to obtain better results.

Fig -6: Back view of integrated Rectenna

3. RESULTS
Fig. 7 shows the simulated result of designed antenna
without rectifier. Fig. 8 shows the simulated result of
antenna integrated with rectifier. It shows -11 dB at 900
MHz for patch antenna without rectifier , while -17 dB at
900 MHz for antenna with rectifier integrated on it which
is quite improved result for rectenna.
Fig.9 shows the comparision of reflection coefficient for
both antenna as well as rectenna. It can be seen that there
is evident reduction in return loss of designed rectenna
when rectifier is integrated into the patch antenna. This
rectenna can then be used for harvesting RF energy from
mobile phones in GSM 900 band.
Fig.10 shows the radiation pattern of the rectenna. The
radiation efficiency is found to be -2.548, thus rectenna
has 55.61 % radiation efficiency.
Fig.11 shows the gain of proposed rectenna. Gain of 3.4
dBi is seen for the design. Also directivity of 5.972 dBi is
obtained which can be seen in Fig. 12.

Fig -5: Front view of 900 MHz Rectenna

© 2015, IRJET.NET- All Rights Reserved

Page 422

International Research Journal of Engineering and Technology (IRJET)

e-ISSN: 2395 -0056

Volume: 02 Issue: 04 | July-2015

p-ISSN: 2395-0072

Fig -7: Simulated S11 of the patch Antenna

www.irjet.net

Fig -10: Radiation pattern of the designed Rectenna

Fig -8: Simulated S11 of the designed Rectenna

Fig -11: Gain plot of the designed Rectenna

Fig -9: Comparision of S11 for patch antenna and
rectenna

Fig -12: Directivity plot of the designed Rectenna

© 2015, IRJET.NET- All Rights Reserved

Page 423

International Research Journal of Engineering and Technology (IRJET)

e-ISSN: 2395 -0056

Volume: 02 Issue: 04 | July-2015

p-ISSN: 2395-0072

www.irjet.net

4. CONCLUSIONS
In this paper, a rectenna is fabricated using a
RMPA, matching network and single stage half wave
rectifier circuit. Here a compact, planar rectenna is
designed for wireless power reception in GSM 900Mhz
frequency band of operations.
The system consists of 3 major blocks. (i) Antenna which
is used for receiving the signal is operated in the far field
region.(ii) Impedance matching circuit which is used for
matching the antenna with the rectifier. (iii) A half wave
rectifier is used to convert the AC to the DC. These blocks
are individually and integrally verified using simulations
and measurements successfully.
There are some improvements which can be done in the
future work. (i) The rectifier can be replaced by the full
wave rectifier for higher efficiency. (ii) The impedance
matching here is generally done for the first harmonics
and the other harmonics are filtered out. Instead of
filtering them, they can also be matched for good
impedance matching. (iii) A rectenna array can be used to
increase the DC signal received at the output.
The circuit can be used to capture the RF energy from a RF
sources by placing it adjacent to RF source (wireless
routers, mobile handset etc.). The circuit can be
implemented in mobile handsets, wireless sensor nodes
etc.
This technique can be helpful in recharging of cell phone
(primary device) by placing another cell phone (secondary
device) to be charged very close to completely charged
mobile handset and draining energy from primary device
for charging the secondary device. Multiple stages of the
voltage multiplier circuit can be used to increase the
output voltage level of the proposed design.

REFERENCES
[1] Mahima Arrawaita, Maryam Shojaei Baghini,
Girish kumar, “RF Energy Harvesting Systems
From Cell Towers in 900 MHz Band”, IEEEConference In Communications, pp. 1-5, 2011.
[2] William C. Brown. “The history of power
transmission by radio waves”. IEEE Trans.MTT,
32(9):1230{1242, 1984.
[3] S.Shrestha, S-K Noh, D-Y Choi, “Comparative Study
of Antenna Designs for RF Energy Harvesting”,
International Journal of Antennas and
© 2015, IRJET.NET- All Rights Reserved

[4]

[5]

[6]
[7]

Propagation, Article ID 385260, 10 pages,
http://dx.doi.org/10.1155/2013/385260, 2013
P. Nintanavongsa, U. Muncuk, D.R. Lewis and K.R.
Chowdhury
“Design
Optimization
and
Implementation for RF Energy Harvesting
Circuits”, in IEEE journal on emerging and
selected topics in circuits and systems Vol. 2,
March 2012.
James O.McSpadden, Lu Fan, and Kai Chang,
“Design and Experiments of a High Conversion
Efficiency 5.8 GHz Rectenna” IEEE Transaction
on microwave theory and techniques, Vol. 46, No.
12,December 1998.
CST Microwave Studio Software, 2010..
Avago Technologies. “Surface Mount Zero Bias
Schottky Detector diode” Technical Data Sheet.

BIOGRAPHIES
B.Hridayeta received her B.E. from
SRCEM, Gwalio(MP).Currently she
is pursuing M.Tech. in Microwave
Engineering
from
MITS,Gwalior(MP). Her research
interest includes Antenna and
Microwave communication and
their applications.

Dr. P.K.Singhal received his his
B.E. and Ph.D. Degrees in
Electronics Engineering from Jiwaji
University, Gwalior (MP)- India, in
1987 and 1997, respectively, and
the M.Tech degree in Microwave
Electronics from the University of
Delhi, India in 1989. Currently, he is
working as Professor, in the
department
of
Electronics
Engineering, Madhav Institute of
Technology and Science, Gwalior
(MP)- India. He has about more
than 100 publications to his credit
at the national and International
level. His research interest includes
electromagnetic,
antennas,
microwave
circuits
&
communication systems.

Page 424

Sponsor Documents

Or use your account on DocShare.tips

Hide

Forgot your password?

Or register your new account on DocShare.tips

Hide

Lost your password? Please enter your email address. You will receive a link to create a new password.

Back to log-in

Close