NIKON - D200 Repair Manual
Content
VBA13001-R.3677.A 作 成承 成承 認印 認印
配 布許 布許 可印 可印 サービス
計画課
Ｍ
VBA13001
REPAIR MANUAL
This website stores data such as cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You may change your settings at any time or accept the default settings.
Privacy Policy Marketing
Personalization Analytics Save Recycled paper Accept All 再生紙を使用しています
Copyrigh ｃ 2005 by Nikon Corporation. All Rights Reserved. 無断転載を禁ず !!
Printed in Japan November 2005
VBA13001-R.3677..A
Specications
Type
Single-lens reex digital camera with interchangeable lenses
Effective pixels
10.2 million
LBCAST image sensor
23.6× 15.8 mm; total pixels: 10.92 m miillion
Image size (pixels)
3872× 2592 (L), 2896× 1944 (M), 1936× 1296 (S)
Lens mount
Nikon F mount (with AF coupling and AF contacts)
Compatible lenses Type G or D AF Nikkor
All functions supported (except IX Nikkor)
Micr Micro o Ni Nikk kkor or 8 85 5 mm F2 F2.8 .8D D
Al Alll func functi tion onss supp suppor orte ted d ex exce cept pt aut autof ofoc ocus us and and som somee expo exposu sure re m mod odes es
Other AF Nikkor
All functions supported except 3D color matrix metering Ⅱ and 3D multi-sensor balanced ll-ash ll-ash for digit digital al SLR
AI-P Nikkor
All functions supported except 3D color matrix metering Ⅱ , 3D multi-sensor balanced ll-ash ll-ash for digit digital al SLR, and and autofocus Can be used in exposure modes A and M; electronic range nder can be used if
Non-CPU
maximum aperture is f/5.6 or faster; color matrix metering, multi-sensor balanced ll-ash for digital SLR, and aperture value display supported if user provides lens data (Non-Ai lens cannot be used.) Picture angle
Equivalent in 35-mm format is approximately 1.5 times lens focal length
Viewnder
Fixed eyelevel pentaprism
Diopter adjustment
－ 2 ～＋ 1 m － 1
Eyepoint
19.5 mm (-1.0 m － 1)
Focusing screen
Type B BriteView clear matte screen Mark Ⅱ provided (Focus frame; grid line display for composition）
ame codata veragsuch e This websiteFrstores as cookies to enable essential site agwell nicaas tiomarketing, n functionality,Mas personalization, and analytics. You eexsettings mirror at any time may changeRyour or accept the default settings. Lens aperture
Privacy Policy Marketing Personalization Analytics Save
Accept All
Approximately 95% of lens (vertical and horizontal) Approximately 0.94× (50-mm F1.4 lens at innity; -1.0 m － 1) Quick return Instant return with depth-of-eld preview
Ｍ1
VBA13001-R.3677..A
FocusFoc us-are areaa sel select ection ion
Nor Normal mal fram framee (11 (11 foc focus us areas areas): ): S Sing ingle le area area or grou group p can b bee select selected ed from from 11 11 foc focus us areas areas Wide frame (7 focus areas): Single area can be selected from 7 focus areas
Len enss sseerv rvo o
In Insstant tant sing singlle-s e-serv ervo AF (S (S); ccon onti tinu nuou ouss-ser -servo vo AF (C (C); ma manual nual (M); M); p prred ediicti ctive focu focuss tra traccking king automatically activated according to subject status in continuous-servo AF (C)
Autofocus
TTL phase de detection b by y Ni Nikon Mu Multi-CAM2000 aau utofocus mo module
Dete Detect ctiion ra rang ngee
-1 -1-- +19 EV (I (IS SO 100, 100, ro room om temp tempeerat ratur uree 20 °C/68 /68 °F)
AF-a AF -are reaa mo mode de
Si Sing ngle le-a -are reaa A AF F, dy dyna nami micc-ar area ea AF AF,, gr grou oup p dyna dynami micc-AF AF,, dy dyna nami micc-ar area ea AF wit with h clos closes estt su subj bjec ectt priority
Foc ocus us lock ock
Foc ocus us can be lo loccked ked by pr pres essi sing ng sh shu utter tter-r -rel elea easse butt button on hal halff-w way (sin (singl glee-se serrvo AF) or by pressing AE-L/AF AE-L/AF-L -L button button
Exposure Metering
Three-mode through-the-lens (TTL) exposure metering
Matrix
3D color matrix metering Ⅱ supported with type G and D lenses; color matrix metering Ⅱ available with other CPU lenses; and color matrix metering available with non-CPU lenses if user provides lens data
Cent Center er-w -wei eigh ghte ted d
Weigh eightt o off 7 75% 5% gi give ven n to to 6, 6, 8 8,, 10, 10, or 13 13-m -mm m ccir ircl clee iin n cen cente terr of of fra frame me,, o orr wei weigh ghti ting ng base based d on on
Spot
average of entire frame Meters 3-mm circle (about 2% of frame); metered area linked to selected focus area (with non-CPU lens, lens, xed in center) EV0 ～ 20 (3D color matrix or center weighted metering）
Range
EV2 ～ 20 (spot metering） （ISO 100 equivalent, f/1.4 lens, 20℃ /68°F）
Exposure meter coupling Combined CPU and AI Expo Exposu sure re m mod odes es
Pr Prog ogra ramm mmed ed aut auto o wi with th ex exib ible le pro progr gram am;; sh shut utte terr-pr prio iori rity ty aaut uto; o; aape pert rtur uree pr prio iori rity ty aaut uto; o; m man anua uall
Exposure Expos ure compe compensati nsation on
±5EV in increm increments ents of 1/3, 1/3, 1/2, 1/2, or 1 EV
Brac Bracke kettin ing g
Expos xposur uree and/ and/or or ash ash br brac acke keti ting ng (2 (2--9 expos xposur urees in inc incre reme ment ntss of 1/3, /3, 1/2, /2, 2/3, /3, or 1E 1EV V) WB (2-9 exposures in increments of 1- 3EV)
Exposure llo ock
Luminosity llo ocked aatt de detected va value w wiith AE-L/AF-L button
Shutter
Electronically-controlled Electronical ly-controlled vertical-travel focal-plane shutter
30- 1/8000 in steps of 1/3, 1/2, or 1EV, bulb Speed This website stores data such as cookies to enable essential site 100 -1600 (in steps of 1/3, 1/2, or 1EV), auto gain to ISO 1600 equivalent functionality,Sensitivity as well as marketing, s ensor), six manual modes with White balance personalization, and analytics. You Auto (TTL white-balance control with 1,005 pixels RGB sensor), may change your settings at any timene-tuning, color temperature setting, preset, white balance bracketing or accept the default settings. Built-in Speedlight
Privacy Policy Guide number (at 20° C/68°F)
Marketing
Personalization Analytics Save
Accept All
Pop-up Speedlight with button release ISO 100: approximately 12 (Manual full-ash: approx. 13)
Ｍ2
VBA13001-R.3677..A
Flash Sync contact
X-contact only; ash synchronization at up to 1/250 s
Flash control
TTL ash control by 1005-segment RGB sensor: - i-TTL balanced ll-ash for digital SLR (built in Speedlight or SB-800/SB-600 with other meterings than spot metering) - Standard i-TTL balanced ll-ash for digital SLR (built in Speedlight or SB-800/SB-600 with spot metering) used) (Can be set on speedlight when SB-800/SB-600 is used) Auto aperture is available with CPU lenses and SB-800 Non-TTL auto is available with SB-800, SB-80DX,SB-28DX, SB-27, SB-2 SB-22S, 2S, etc Range-priority manual is available with SB-800
Sync modes
Front curtain sync (normal), slow sync, rear-curtain sync, red-eye reduction, red-eye reduction with slow sync
Flash-ready indicator
Lights when B-800, SB-600, SB-80DX, SB-28DX, SB-50DX, SB-28, SB-27, B-22S, etc, is fully charged; blinks for 3 sec. after ash is red at full output
Accessory shoe
Standard ISO hot-she contact with safety lock
Advanced Wireless Lighting (with SB-600 Creative Lighting System - with SB-800, SB-600, or SB-R200, supports Advanced and SB-R200, remote only) Setting Comand mode can control built-in Speedlight as Master ash - Supports Auto FP High-Speed Sync, Flash Color Information Communicatio Communication, n, modeling illumination,, and FV lock illumination
This website stores data such as cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You may change your settings at any time or accept the default settings.
Privacy Policy Marketing Personalization Analytics Save
Accept All
Ｍ3
VBA13001-R.3677..A
Storage Media
Type I and II CompactFlash memory cards; Microdrives
Fil ilee sy syst stem em
Com ompl plia ian nt wit ith h DC DCF2. 2.0 0 (D (Des esig ign n Rul ulee ffor or Cam amer eraa File ile Syst ystem ems) s) an and dD DP POF (Dig (Digit ital al Print int Order Format)
Compression
- Compressed NEF (RAW): 12-bit (about 50％～ 60％ ) compression - JPEG baseline-compliant (size priority, priority, image priority can be selected)
Self-timer
Electronically controlled timer with 2, 5, 10, and 20 sec. duration
Depth-of- Depth -of-eld eld p previe review w
Lens aperture aperture sstoppe topped d down when depth depth-of- -of-eld eld p previe review w button button iiss pre pressed. ssed. Stopped down up to set aperture value with A・M mode; up to control aperture value with P・S mode.
Monitor
2.5”, 2 23 30,000-dot, llo ow-temperature p po olysilicon T TF FT LCD wi with b brrightness ad adjustment
Video output
Can be selected from NTSC and PAL
External interface
USB 2.0 Hi-Speed
Tripod socket
1/4 (ISO 1222)
Firmware updates
Can be updated by users
Language
German, E En nglish, S Sp panish, F Frrench, K Ko orean, IIttalian, D Du utch, P Po ortuguese, R Ru ussian, S Sw wedish,
Power source
simplied Chinese, and Japanese - One rechargeable rechargeable Nikon EN-EL3e lithium-ion battery Voltage 7.4V DC［Quick charger MH-18a］is used
- MB-D200 multi-power battery pack (available separately) with one or two rechargeable Nikon EN-EL3e EN-EL3e lithiumlithium-ion ion batteries or six (LR6 (A (AA) A) alkaline, ZR6 nickel-manganese, nickel-manganese, or HR6 nickel-metal-hydride) batteries - EH-6 AC adapter (available separately) Dimensions
Approximately 147×113× 74 mm
（W× H×D）
Weight
Approximately 830g without battery, memory card, body cap, or LCD monitor cover
Operating environment Temperature
0 ～ 40℃
Humidity
Less than 85％ (no condensation)
This website stores data such as ● Unless otherwise stated, all gures are for a camera with a fully-charged battery operating at an ambient temperature of 20°C (68° cookies to enable essential site functionality,F).as well as marketing, personalization, andreserves analytics. You to change the specications of the hardware and software described this manual at any time without prior ● Nikon the right may change your settings at any time notice. Nikon will not be held liable for damages that may result from any mistakes that this manual may contain. or accept the default settings.
Privacy Policy Marketing Personalization Analytics Save
Accept All
Ｍ4
VBA13001-R.3677.A
Points to notice for Disassembly and Assembly
�
WARNING 警告
Take extra care not to get an electric shock when detaching covers. カバーを外した後は、修理指針の指示に従ってメインコンデン After removing covers, be sure to discharge the main condenser according to the instructions of repair manuals. サーの放電を必ず行うこと。 内部に高電圧部あり。カバーを外す時は感電に注意すること。
Caution:
①
In disassembly/(re)assembly, disassembly/(re)assembly, be sure to use conductive mat (J5033) and wrist strap (J5033-5), in order to protect electric parts from static electricity. electricity.
②
Before disassembling, be sure to remove batteries or AC power cord.
③ In disassembling, be sure to memorize the processing state of wires and FPC, screws to be xed and their types, etc.
④ The low-pass lter of the image image PCB is easily damaged. Handle it very carefully.
Points to notice for Lead-free solder products ・ Lead-free solder is used for this product . ・ For soldering work, the special solder and soldering iron are required. ・ Do NOT mix up lead-free solder with traditional solder.
This website stores data such as cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You may change your settings at any time or accept the default settings.
Caution: When "Separation of Front body from Rear body", "Disassembly of CCD/FPC unit" and Privacy Policy "Disassembly of Bayonet" are performed, be sure to carry out "RESET AF-DEFOCUS MarketingCOMPENSATION" of the D200 adjustment software after assembly. Personalization Analytics Save
Accept All
Ｄ1 ･
VBA13001-R.3677.A
Disassembly 1. Separate Front and Rear bodies External rubber
･ Remove the external rubbers
I S O
(#B63,#B60,#B61,and #B447).
W B Q U A R
#B61
#B447
#B63
#B60
Bottom cover
･ Remove the battery lid (by tilting and pulling it). Takee out two screws (#1556), six screws (#1549) and two screws (#1547). ･ Tak This website stores data such as #1547 cookies to enable essential site cover. the bottom ･ Remove functionality, as well as marketing, personalization, and analytics. You may change your settings at any time or accept the default settings. Privacy Policy
#1547
Marketing
Bottom cover
Personalization Analytics Save
#1549×6
Accept All #1556
#1556
･ - Ｄ2
-
VBA13001-R.3677.A Rear cover Takee out two screws (#1552), two screws (#1547) and one screw (#1549). ・ Tak cover. ・ Remove the rear cover.
#1549
#1547×2
#1552×2
Be careful NOT to cut the TFT-PCB connection connection
・
FPC that is at the lower side of the rear cover.
TFT-PCB connection FPCs from the connector. ・ Remove the three TFT-PCB
This website stores data such as cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You may change your settings at any time or accept the default settings.
Privacy Policy Marketing Personalization Analytics Save
Accept All
･ - Ｄ3
-
VBA13001-R.3677.A
�
WARNING 警告
Ta Take ke extra care not to get an electric shock when 内部に高電圧部あり。カバーを外す時は感電に注意すること。 detaching covers. カバーを外した後は、修理指針の指示に従ってメインコンデン After removing covers, be be sure to discharge the main サーの放電を必ず行うこと。 condenser according to the instructions of repair manuals. manuals.
I/F cover ・ Take out two screws (#1549). ・ Remove the I/F cover unit.
#969
#962×3
#392
#394 #393 #1549×2 #1642×2
#969
#395 #965
#1643
Discharge of Main condenser
・ Discharge the main condenser .
This website stores data such as cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You may change your settings at any time or accept the default settings. ２ＫΩ / ５Ｗ
Privacy Policy Marketing Personalization Analytics Save
Accept All
･ - Ｄ4
-
VBA13001-R.3677.A
Disassemble Rear Cover #467 #1538 × 2
#RP00007
#985 #481
#469
#474 #986
#468
#455 #476
#465
#426 #924
#1511 × 2 #1630
#1631 #478 #472 This website stores data such as cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You may change your settings #473at any time or accept the default settings.
Privacy Policy Marketing
#477 #456
#479 #1020
#1511 × 2
#470
#430
Personalization Analytics Save
Accept All#480
#422
#1512 × 3
･ - Ｄ5
-
VBA13001-R.3677.A #431 #433
#434 × 2 #435 × 2
#488 #1057 #1626
#489
#1629 #487
#1633 #492
#484
#432 #483 × 2 #485 #1546
#440 #491 #1571 #486
#987
#1632 × 2 This website stores data such as #427 cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You may change your settings at any time or accept the default settings.
#1518 × 2 #921
#441
#425
Privacy Policy
#922 #445
Marketing Personalization Analytics #429
Save
Accept All #423
#443
#424 #442 #1628 × 2 #923
･ - Ｄ6
-
VBA13001-R.3677.A DG shield plate Takee out ve screws (#1546) and two screws (#1515). Tak
・
#1515
Remove the soldering bridge.
・
Remove the DG shield plate unit (#683, #696).
・
DG shield plate unit
Soldering bridge
#1515
DG-PCB unit ・ Remove the tape (#926). ・ Remove ve FPCs from the connector. ・ Remove the two harnesses from the connector.
・ Unsolder the four wires. DG-PCB unit (#B1017). ・ Remove the DG-PCB #926
This website stores data such as cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You may change your settings at any time or accept the default settings. #926
#B1017 DG-PCB unit
Privacy Policy Marketing Personalization Analytics Save
Accept All
Harness Harness
#1546×5
･ - Ｄ7
-
VBA13001-R.3677.A CCD/FPC unit CF card holder
Takee out three screws (#1639) and remove the CCD/FPC unit (#B2032). ・ Tak Takee out three screws (#1543) and remove the CF card holder (#1018). ・ Tak #1639×3
#1543×3
#1018 CF card holder
#B2032 CCD/FPC unit
Takee out the screw (#1539) and remove the conductive plate (#691). Tak
・
Takee out four screws (#1539) and remove the conductive plates (#689, #690,and #688). Tak
・
Remove the main connection FPC (#1035) from the connector of tthe he power drive PCB (#1002).
・
#1539
Power drive PCB (#1002) △(Addition）
#1539 Conductive plate (#689)
This website stores data such as cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You may change your settings at any time or accept the default settings. Conductive plate
Privacy Policy (#690) Marketing
Personalization
#1539
Analytics Save
#1539 Conductive plate (#688)
Accept All
#1543 #1539
△(Revice）
Conductive plate (#691) サービス
計画課 Ｍ
Change page △ ×1
･ - Ｄ8
-
JUL.7.2006
VBA13001-R.3677.A Power drive PCB
・ Unsolder six wires. ・ Remove the harness of the back of the power drive PCB. Takee out two screws (#1541) and remove the power drive PCB. ・ Tak
#1541
Brown: Main-PCB Yellow: Main-PCB
Black: Charge motor Red: Charge motor
Blue:AF motor
#1541
Power drive PCB (#1002)
This website stores data such as DC/DC PCB Harness: cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You may change your settings at any time or accept the default settings.
Privacy Policy
#1075
Marketing Personalization Analytics Save
Accept All
Orange:AF motor
･ - Ｄ9
-
VBA13001-R.3677.A DC/DC PCB unit
・ Unsolder six wires. Takee out four screws (#1541) of the DC/DC-PCB (#1047). ・ Tak
・ Remove the harness (#1074) from the DC/DC-PCB (#1047). ・ Remove the harness (#1075) from the DC/DC-PCB (#1047) and from the connector of the power drive PCB (#1002). Black: Battery contact Red: Battery contact
#1541
#1541
Yellow:SBDI-PCB Brown: SBDI-PCB Black: IF-PCB Red: IF-PCB
#1541 #1541 #1047 △(Addition）
Harness: DG-PCB
This website stores data such as cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You may change your settings at any time or accept the default settings.
Harness: Power drive PCB
#1074
#1075
Privacy Policy Marketing Personalization Analytics Save
Accept All
サービス
計画課
Ｍ
･ - Ｄ10
Change page △ ×1
-
JUL.7.2006
VBA13001-R.3677.A Top cover
・ Remove the tape (#930). ・ Unsolder four wires. Tape (#930)
Red: SB-PCB Black: SB-PCB
Yellow: SB-PCB Brown: SB-PCB
・ Remove the cover (#850). Take out the screw (#1622) , and remove the diopter adjustment knob unit (#852, #857, #851). (#1548). ・ Pop the SB up, and take out two screws (#1548). (#1511), two screws (#1547) and two ・ Take out two screws (#1511), screws (#1555).
Pop this up. #1548×2
unit slowly not to cut the the FPC. ・ Lift the top cover unit
#1511
#1511
#1555
#1555
This website stores data such as #1547 #1547 cookies to enable essential site functionality, as well as marketing, the top cover connector.. ・ Remove personalization, and analytics. You FPC (#1003) from the connector may change your settings at any time or accept the default settings.
#1555
#852
#851
#857
#850
#1622
Privacy Policy Marketing Personalization Analytics Save
Accept All
#1003 △(Addition）
サービス
計画課
･ - Ｄ11
Change page △ ×1
-
JUL.7.2006
VBA13001-R.3677.A
Disassembly of Top cover unit SB upper case
・ Push the pop-up lever A-part of the top cover unit, and lift the built-in SB. Take ake out two screws (#1623). (Fig.1) ・ T the SB lower case on the top cover. cover. Then while holding holding the hooks of the SB upper case ・ Fold down #301 of the from both sides by hand, release them from the two holes by sliding/tilting, sliding/tilting, then remove #301. (Fig.2） #1623×2 Pop-up lever A-part
Fig.1
Push
SB lower case unit SB upper case Hooks
#301
Fig.2
Holes
This website stores data such as cookies to enable essential site functionality, as well as marketing, SB and lockanalytics. cover You personalization, may change your settings at any time or accept the default settings.
Privacy Policy
#917C #310
Marketing Personalization Analytics
#309 #312
・ Remove the spring (#310). Save・ #309 comes Accept off. All #1565
･ - Ｄ12
-
VBA13001-R.3677.A Removal of Top cover FPC / Wires / SB-PCB
・ Unsolder the three metering mode FPC lead wires.
△(Addition）
・ Unsolder the accessory shoe contact at four locations. Metering mode FPC lead wire Red×1, Brown×1, Black×1 Red, Brown, Black △(Revice） Accessory shoe contact×4
・It demounts tapes.
・ Unsolder the seven lead wires of the SB-PCB. ・ Take out the screw (#1601). ・ Remove the FPC of SB-PCB (#B1013). ・ Take out the screw (#1511). ・ Take out the screw (#1535). ・ Take out the screw (#1541). SB(Orange) SB(Gray) SB(Black) SB (Green) SB(Red) Sync terminal(Green terminal(Green))
This website stores data such as cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You #1601 may change your settings at any time or accept the default settings.
SB(White)
Privacy Policy #1511
Marketing
#1535
Personalization FPC
#B1013
Analytics Save
Accept All #1541
サービス
計画課
･ - Ｄ13
Change page △× 2
-
JUL.7.2006
VBA13001-R.3677.A SB-up spring
・ Remove the SB-up spring (#305) from the hooking part. Takee out the screw (#1601) and remove the SB-up spring (#305). ・ Tak #305
#305 #1601
Hooking part
SB lower case unit ・ Pull each wire from the holes. ・ While releasing the two hooks of the collar (#308), remove #308. ・ Remove the rotation axes (#306 and #307). ・ Remove the SB lower case unit (#B302) from the top cover. Pull six wires out from the holes. #B302
#307 Hooks
This website stores data such as cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You may change your settings at any time #306 or accept the default settings. ・ Remove #796, #322, and #325. #796×2 △(Revise）
#308
Be careful of the direction of assembling.
#796
Privacy Policy Marketing
#325 #322
Personalization Analytics #796
Save
Accept All
サービス
計画課
Ｍ
･ - Ｄ14
Change page △× 1
-
JUL.7.2006
VBA13001-R.3677.A
M/DFPC unit ・ Remove the FPC soldering bridges of #1025 and #1026. ・ Take out the screw (#1569). ・ Detach #1025 from the bosses. ・ Unsolder the lead wire (#1094). ・ Remove the solder of the lead wire (#1094). △ (Addition） ・ Lift the FPC, and take out the screw (#1572). ・ Remove B502 and B504 (Trefoil button unit). Tre o
69
utton un t
So er ng r ge
1026
94 Green
1025
Screw (#1572)
Boss B502 I S O
B504
Q U A R
1026FPC
50
△ (Addition）
W en remov ng t e so er on t e sync ro-term na un t, unso er w t n 2 sec.
513 1532
This website stores data such as cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You may change your settings at any time or accept the default settings.
46
508 509
1025FPC
Privacy Policy
514 515
Marketing
1544×2 1569
Personalization
B505
Analytics 1569
Save
510
Accept All
1572
1569
Use the Hexagonal of 5-mm diameter wrench サービス
計画課
Ｍ
Changed page △ ×2
Ｄ15 ･
-
Aug.8.2006
VBA13001-R.3677.A Top cover FPC unit
・ Remove the soldering bridges . ・ Unsolder the SUB dial command unit (B725) . ・ Take out two screws (#1544). ・ Remove the SUB command dial unit (B725). ・ Unsolder the MAIN command dial unit (B726) . ・ Take out two screws (#1571). ・ Remove the MAIN command dial unit (B726). ・ Remove the relies SW unit .
#1544×2
Soldering bridge × 9
B725
#B725 #704 #707×2
Solder
#1544×2
#1053 B726
#973 #706
#1571 #705 #321×4
#974 #39 #1003 #781
#780
This website stores data such as cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You may change your settings at any time or accept the default settings.
#913 #784 #914 #1028
#1117(Red)
Privacy Policy
#965
#B782 #1544×3
#1119(Black) #1118(Brown)
#1535
Marketing
#929 #B726
Personalization Analytics Save
#703
#912
Accept All
#1571×2
#1033
･ - Ｄ16
-
VBA13001-R.3677.A Release button / Other small parts
#732 #733 #734 #742
#743 #24
#701
#B43
#787
This website stores data such as cookies to enable essential site functionality, as well as marketing, #1659You personalization, and analytics. may change your settings at any time #RP5 or accept the default settings.
#911
#966
#1557×2
Privacy Policy
#1604
Marketing
#1652
Personalization #748×2 #749
Analytics Save
#1608×2
Accept All
#730
･ - Ｄ17
-
VBA13001-R.3677.A Outer LCD window / Shoe mold unit / Accessory shoe / Other small parts
#502 I S O
W B Q U A R
#501
#1026 #516 #503 #318 #1640×2 #316 #504 #507 #1533
#B317
#512
#701
#511
#324 #B735
#327 #323
#1605 This website stores data such as cookies to enable essential site functionality, as well as marketing, #766×2 personalization, and analytics. You may change your settings at any time or accept the default settings. #731
Privacy Policy
#1565 #765×2
#1540×2
#1560
Marketing Personalization
#750
#753 #747 #1537×2
Analytics Save
#1606
Accept All #1547×2
#746
･ - Ｄ18
-
VBA13001-R.3677.A Main PCB unit
・ Unsolder thirteen wires. F PCs from the connector. ・ Remove ve FPCs Takee out three screws (#1616) and remove the main PCB unit (#B1001). ・ Tak Black: Charge SW Brown: Charge SW Red: Charge SW Purple: Battery contact Blue：FG-ID Black: AF-assist illuminator Gold: AF-assist illuminator
Black: Buzzer Black: Buzzer
Black: 10-pin FPC Red: 10-pin FPC
#1616×3 △(Addition）
Yellow: Lens contact
FPC
Brown: Lens contact FPC
・ Unsolder the two wires of the back of the main PCB unit (#1001). ・ Remove the main connection FPC (#1035) from the connector of the back of the main PCB unit (#1001).
This website stores data such as cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You may change your settings at any time or accept the default settings.
Back of Main PCB (#1001)
Privacy Policy Marketing Personalization Yellow: Power drive PCB Brown: Power drive PCB
Analytics Save
Accept All
サービス
FPC (#1035)
計画課 Ｍ
･ - Ｄ19
Change page △ ×1
-
JUL.7.2006
VBA13001-R.3677.A Separation of Front body from Rear body
・ Take out two screws (#1529), one screw (#67), two screws (#1531), one screw (#1525) and ve screws (#1575).
・ Release the AF motor wires from the bosses, and while pulling them slowly from the holes of the rear body,, remove the front body front body. body.
AF motor wires
Rear body #1531×2
#1525
Front body AF motor wires
This website stores data such as cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You may change your settings at any time or accept the default settings.
#1529×2
#67
Privacy Policy Marketing Personalization Analytics Save
Accept All #1575×5
･ - Ｄ20
-
VBA13001-R.3677.A Grip unit
・ Remove the grip (#57) with the screw (#1515) and two screws (#1509).
#826 #952 #952
#58
#1517
#1515 #828 #1559 #829 #1509 #1509
This website stores data such as cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You may change your settings at any time or accept the default settings.
Privacy Policy Marketing Personalization Analytics Save
Accept All
#439 #57 #769
#1541
･ - Ｄ21
-
VBA13001-R.3677.A
2. Front body Metering FPC unit Prism box unit (with prism and eyepiece)
・ Remove the metering FPC from the connector of the SI#883×3
FPC (#1005). Take ake out three screws (#883), and remove the metering ・ T
#B1006
FPC unit (#B10006). Ａ
・ Three springs (#884) come off. ・ Take out two screws (#1617) and remove the metering #884×3 FPC unit pedestal (#B882). #1617×3
Caution:
#B882
The screw (#883) is attached with the adhesive. In case the screw (#883) is moved, the AECCD positioning adjustment (ref. #1528
Assembly) becomes necessary.
#1525
#1528
・ Remove the lens contact FPC unit (#B1008) from the
#1525 Ａ
connector of the SI-FPC (#1005). Ｂ
・ Take out two screws (#1525) and two screws (#1528), and
remove the prism box unit from the front body.
This website stores data such as cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You may change your settings at any time or accept the default settings.
Privacy Policy Marketing Personalization Analytics Save
Accept All
#1005
Ｂ
･ - Ｄ22
-
VBA13001-R.3677.A Eyepiece lens-barrel unit Inner LCD unit
Takee out two screws (#1619), and remove the eyepiece lens-barrel unit. ・ Tak
the nder-display nder-display FPC (#1004) from the connector of the SI-FPC. ・ Remove the unit. ・ Take out two screws (#1618), and remove the nder-display LCD unit.
#7 #847
#B846
#844 #1539 #848 #841
#849
#856
#853 #845
#854
#5 #1539 Ａ
#842
#858 #1619x2
#1005
Ａ
This website stores data such as cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You may change your settings at any time or accept the default settings.
#1054
Marketing Personalization
Save
#1056 #878
Privacy Policy #1618×2
Analytics
#1004
#879
Accept All
･ - Ｄ23
-
VBA13001-R.3677.A Penta unit #B1005
*
#954
#953
#1619x2 #8
#955
#832
#840
#904
#837 #875x2
#876
#833 #839
#1055 #838x2
#901
* #902
#834
This website stores data such as cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You may change your settings at any time or accept the default settings.
Privacy Policy
#877A～B
#872x2 #874x2 #877C×2
#836A～C
Marketing Personalization
#3
Analytics Save
#873x2
Accept All
#835
･ - Ｄ24
-
VBA13001-R.3677.A AF-PCB unit
・ Take out the screw (#1507). connector. ・ Remove the AF-PCB FPC from the connector. Takee out the three screws (#295) with the Hexagonal wrench, and remove the AF-PCB unit (#B1007). ・ Tak
・ Three springs (#293) come off.
#295×3
#B1007 #1507
#293×3
This website stores data such as cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You may change your settings at any time or accept the default settings.
Privacy Policy Marketing Personalization Analytics Save
Accept All
･ - Ｄ25
-
VBA13001-R.3677.A 10-pin plug 10-pin FPC unit ・ Unsolder six wires. ・ Remove the soldering bridge at nine locations of the 10-pin terminal (#41) and 10-pin FPC. ・ Remove the soldering bridges at eight locations of the 10-pin FPC (#1010) and the lens contact FPC. Take ake out the screw (#1503) and remove the 10-pin FPC (#1010). ・ T Take ake out the screw (#65) and remove the 10-pin terminal. ・ T
Red: Main PCB unit Black: Main PCB unit #B1008
Blue: Lens release SW
#1010
△(Revice）
Green: SCM-change PCB #1503
Red: SCM-change PCB #1010
This website stores data such as cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You may change your settings at any time or accept the default settings.
Black: SCM-change PCB #65
#41
#968
Privacy Policy Marketing Personalization Analytics Save
Accept All
サービス
計画課
Ｍ
Ｍ ･ - Ｄ26
Change page △ ×1
-
JUL.7.2006
VBA13001-R.3677.A Bayonet unit Aperture coupling-ring unit SCM-change lever unit Front cover unit
・Remove the SCM screw cover plate (both-sided adhesive tape: #389). Take out the screw (#1551) and remove the SCM-change lever (#383). Takee out four screws (#1621) and the screw (#1620), and remove the bayonet (#401) and the bayonet spring ・ Tak (#402). off, ・ Remove the front cover (#22) and the aperture coupling ring. (The aperture coupling-ring roller comes off, too.)
#980
#40 #38×2 #37
#407
#388
#1551 #773 #383
#1514
#66 #22
This website stores data such as cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You may change your settings at any time or accept the default settings.
#406
#402 #401
Privacy Policy
#1621×4
Marketing Personalization #RP1(404,405)
Analytics Save
Accept All
#1620
･ - Ｄ27
-
VBA13001-R.3677.A Lens release SW Lens release PCB unit Vertical-shooting lever SCM-change PCB
#66×3 Black Brown Red
#1516
#381
#1568 #1527
#979
#378 #380
#1034
#379
#978
#1563
#356 #386
#385 #977
#377
#1539×2
△(Revice） Blue
#382
#1116
#357 #359 #384
#376
#1654x2 #372
This website stores data such as cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You may change your settings at any time or accept the default settings.
#371
Privacy Policy Marketing Personalization Analytics Save
Accept All
サービス
計画課
Change page △×1
･ - Ｄ28
-
JUL.7.2006
VBA13001-R.3677.A AF drive-PCB unit Horizontal-shooting Horizontal-shoo ting lever unit
Takee out the screw (#1513) and remove the horizontal-shooting lever unit (#B355) and the coupling shaft Tak
・
(#342). Remove the soldering bridges at four locations of the AF drive FPC.
・
Take out two screws (#1636) and remove the AF drive-PCB unit (#B328).
・
△(Revice） #1513
#342
#1531
#B355
#1636
#343x2
This website stores data such as cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You may change your settings at any time or accept the default settings.
#344x2
Privacy Policy Marketing Personalization Analytics Save
Accept All サービス
計画課
Ｍ ･ - Ｄ29
Change page △ ×1
-
JUL.7.2006
VBA13001-R.3677.A Mirror BOX unit I-base plate unit 45°-support base plate Mirror unit
・ Remove the FPC of the I-base plate unit (#B71) from the connector of #B1009. Be careful NOT to lose lose the washers (#236A (#236A - E).
#233
#1523x2
#231 #1525
#232
B10201
#229
#214
#343 #222
#B10212
#242
#1568
#210
#236A~Exn #960
This website stores data such as cookies to enable essential site #B71 functionality, as well as marketing, personalization, and analytics. You #1523x2 may change your settings at any time or accept the default settings.
△(Addition） #B1009
Privacy Policy Marketing
#170
Personalization Analytics Save
Accept All #1530
サービス
計画課
Ｍ ･ - Ｄ30
Change page △ ×1
-
JUL.7.2006
VBA13001-R.3677.A Lens-contact unit F-F0 PCB unit Mirror-support Mirror-suppo rt sponge Front plate-FPC unit Preview button Function button Lens contact FPC unit
Remove the soldering bridges at three locations of #B1024 and #B1008.
・
Remove #1024 from #26.
・
Unsolder #B411 and #B1008 at eight locations.
・
Take out the screw (#1525) and remove the lens-contact unit (#B411).
・
Yellow: Main PCB unit Brown: Main PCB unit
#B1009
B1008
Solder
#1507x2
Soldering bridge
#1510x4 #235 #234
This website stores data such as#35x2 cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You may change your settings at any time or accept the default settings.
Soldering bridge
#B1024 #412×2� #B411
#1652x2
Privacy Policy Marketing
#1525 #934x2
Personalization
#26 #36x2
Analytics
#33x2
Save
Accept All
･ - Ｄ31
-
VBA13001-R.3677.A
2. Rear body DC/DC-PCB shield plate #1537×2 #687
Takee out two screws (#1537) and the screw (#1539). ・ Tak
・ Remove the DC/DC-PCB shield plate (#687).
#1539
Main condenser/DI-PCB
Takee out the screw (#1564), and remove the DI・ Tak PCB (#1029).
・ Remove the condenser (#1067). #1067
This website stores data such as cookies to enable essential I/F-board unit site functionality, as well as marketing, personalization, and analytics. You may change your settings at any time or accept the default settings. ・ Take out two screws (#1543).
・ Remove the I/F-board unit (#B1019). Privacy Policy Marketing Personalization Analytics Save
Accept All
#1564
#1029
#B1019
#1543×2
･ - Ｄ32
-
VBA13001-R.3677.A #397
・ Remove the IF GND steel plate (#397).
AF-assist lamp #1368
・ Take out the screw (#1368). ・ Remove the AF-assist lamp (#B326).
#B326
U/D base plate
・ Take out the screw (#1572). ・ Take out three screws (#1573). This website stores data such as cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You may change your settings at any time or accept the default settings.
#B16620
Privacy Policy
#1573×3
Marketing Personalization Analytics Save
Accept All
#1572
･ - Ｄ33
-
VBA13001-R.3677.A Shutter unit
・ Remove the retaining tape (#956). ・ Take out three screws (#1541). ・ Remove the GND steel plate (#398). ・ Remove the shutter unit (#31).
#31
#398
#956 #1541×3
Option pack FPC
・ Take out four screws (#1542). Remove thesuch option ・stores This website data as pack FPC (#1027). cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You may change your settings at any time or accept the default settings.
#1027
Privacy Policy Marketing #1542×4
Personalization Analytics Save
Accept All
･ - Ｄ34
-
VBA13001-R.3677.A Battery contact spring
#B823
・Take out the screw (#1567), and remove #B822. ・Take out the screw (#1567), and remove #B823. ・Take out the screw (#1540), and remove #B824.
#1567
#1540 #B824
#1567
#B822
Rear body small parts
#1641×2
#915×2
#682×2
This website stores data such as cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You may change your settings at any time or accept the default settings.
Privacy Policy Marketing
#889×2
Personalization Analytics Save
Accept All
#959
･ - Ｄ35
-
VBA13001-R.3677.A Rear body small parts
・Attach two #682 on the body and x them with two screws (#1641). ・Attach two #889 to cover the screw holes without fail. ・Attach the 2 pieces of the both-sided adhesive tape (#915).
#1641×2
#915×2 Position for attaching #915
#682×2
（at 2 locations)
#889×2
#959
Battery chamber cover tape
Attachdata the tape by aligning with the reference position. ・stores This website such(#959) as cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You may change your settings at any time or accept the default settings. #959
Privacy Policy
Without
Marketing
running off the
Personalization Analytics Save
Reference position
Accept All
edge
- Ａ1 ･
-
VBA13001-R.3677.A Both-sided adhesive tape (to collect dust around aperture)
・Attach 4 pieces of #244 on the body.
※ Attach the tape from the inside without any slackness, then fold it down to conform to the shape of the corner.
#244
Attach the tape without any gap at the corner.
#244×4
Battery contact spring Arrange the wires in the groove #B823
・Assemble #B824 into the body by tting in the boss of the body.
・Tighten the screw (#1540). #1567
・Assemble #B822 into the body. ・Tighten the screw (#1567).
#1540 #B824
This website data#B823 such as Assemble into the body. ・stores cookies to enable essential site Tighten screw (#1567). ・as functionality, well asthe marketing, personalization, and analytics. You may change your settings at any time the wires (red and black) in the ・Arrange or accept the default settings.
#1567
groove. Privacy Policy Marketing #B822
Personalization Analytics Save
Accept All
- Ａ2 ･
-
VBA13001-R.3677.A Optional pack
・Attach the both-sided adhesive tape (#927) on #1027.
Position for attaching the both-sided adhesive tape
※ Do NOT cover the positioning hole of #1027. ・Attach #1027 on #825. ・Attach #994 on #1027.
#1027
・Make a crease on #1027. body, and tighten four screws (#1542) in ・Assemble #825 in the body,
#927
order.
Positions for folding FPC
#1542×4
④ Valley fold
② ③
Mountain fold
① #825
#825 #927
#994
This website stores data such as cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You may change your settings at any time or accept the default settings.
Privacy Policy Marketing Personalization Analytics Save
Accept All
#1027
- Ａ3 ･
-
VBA13001-R.3677.A Shutter unit
Position for attaching the both-sided adhesive tape
・Attach the both-sided adhesive tape (#245 and #246) on #31 to collect dust. #31
※ When attaching, be careful NOT to give pressure on the shutter shutter side.
#246
#245
Installment of Shutter unit
body. (ref. Page A2） ・Peel off the four pieces of the backing paper (#244) that were attached on the rear body.
・Assemble the shutter unit (#31) into the body. ・Assemble the GND steel plate (#398). ・Tighten three screws (#1541) in order. ・Attach the retaining tape (#956) as shown below. #31
②
This website stores data such as cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You may change your settings at any time or accept the default settings.
#31
③ ①
Privacy Policy Marketing
#1541×3
Personalization #398
Analytics Save
#956
Accept All
- Ａ4 ･
-
VBA13001-R.3677.A U/D PCB unit body. ・Assemble the U/D PCB unit (#B16620) in the body.
① The shutter must be in state of charging (being about to be released). (Check this by the shutter curtain.) ② The charging SW must be at the initial position. (All the brushes are on the gold pattern.) ③ The mirror charge lever and shutter charge lever must be at the initial position. ③ Charg Charge e lever(Mirror): lever(Mirror): ① In state of charging
② Charge SW:
No gap
Initial position
OK
lever(shettur): ③ Charge lever(shettur): Initial position
NG
・Tighten three screws (#1573) in order. This website stores data such as ・Tighten the screw (#1572). cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You may change your settings at any time or accept the default settings.
#1573×3
②
#B16620
Privacy Policy ③
Marketing Personalization
④
Analytics Save
Accept All
①
#1572
- Ａ5 ･
-
VBA13001-R.3677.A AF-assist lamp
・Hook the shutter FPC to the boss. (See below) ・Put the AF-assist lamp (#B326), and tighten the screw (#1638).
FPC hooking position #1638
#B326
Lamp positioning pinhole
I/F board unit Positioning boss×4 #397
・Fit the I/F GND steel plate (#397) in the positioning bosses. bosses.
・Put and x the I/F-board unit (#B1019) with two screws (#1543). This website stores data such as cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You may change your settings at any time or accept the default settings.
#B1019
Privacy Policy Marketing Personalization Analytics Save
Accept All #1543×2
- Ａ6 ･
-
VBA13001-R.3677.A Main condenser/DI-PCB
body, ・Assemble the main condenser (#1067) in the body, and attach two pieces of the both-sided adhesive tape (#915). When the main condenser is
※ Refer to the below for the lead direction of the
mounted, the connector must be
main condenser.
closed.
・Mount the DI-PCB (#1029), and tighten the screw (#1564).
#915×2 Position by following the direction of the arrow
This website stores data such as cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You Direction of leads of may change your settings at any time the main condenser or accept the default settings. #1564
Privacy Policy Marketing Personalization Analytics Save
#1067
Accept All
#1029
- Ａ7 ･
-
VBA13001-R.3677.A DC/DC shield plate
・Attach the DC/DC-PCB insulating sheet (#697) on the DC/DC-PCB shield plate (#687).
#687
Reference position
#697
body. ・Assemble the DC/DC-PCB shield plate (#687) in the body.
Put the bending portions of #687 into the square holes of the body.) body.) （
・Tighten two screws (#1537). ・Tighten screws (#1539). △(Addtion） #1537×2 #687
This website stores data such as cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You may change your settings at any time or accept the default settings.
Privacy Policy Marketing Personalization Analytics Save
Accept All #1539 △(Addtion）
サービス
計画課
Ｍ - Ａ8 ･
Change page △ ×2
-
JUL.7.2006
Assembly / Adjustment
VBA13001-R.3677.A NOTE: For undescribed undescribed tapes and sponges here in"Assembly", in"Assembly", refer to PARTS LIST.
・
1. Front body Lens-contact unit F-F0 PCB unit Mirror-support sponge Front plate-FPC unit Preview button Preview Function button Lens contact FPC unit
Oil barrier: OS-30MF
・ Position #B411 upwards, and x it with the screw (#1525). ・ Attach #B1024 by aligning with the positioning boss of #26. ・ Solder #B411 and #B1008 at eight locations. ・ Make soldering bridges of #B1024 and #B1008 at three locations. Yellow: Main PC PCB B unit Brown: Main PCB unit #B1009
B1008
Solder #1507x2
Soldering bridge
#1510x4 #235
This website stores data such as cookies to enable essential site #35x2 functionality, as well as marketing, personalization, and analytics. You may change your settings at any time or accept the default settings.
#234
Soldering bridge
#B1024 #412×2� #B411
Privacy Policy
#1652x2
Direction
Marketing
for Position
#1525
Personalization
#934x2
Analytics Save
#26
Accept All
#36x2
Grease: G-92KA #33x2
- Ａ9 ･
-
VBA13001-R.3677.A Installment of Mg
・ When mount each Mg, arrange clearances between the U-groove lever and the
U-groove lever
iron core. Check the clearances when the iron core of Mg is attached.
Iron core of Mg Mirror-drive Mg (#131)
Ratchet gear
Locking lever
0 .2 .2 ～ 0 .3 .3
#134×2 Adhesive: Screwlock
When the aperture-stop Mg is attached, in order to leave clearances of 0.2-0.3 mm between the ratchet gear and locking lever, put the 0.2-mm washers, etc, in the clearances, and x the Mg with two screws
Adhesive:
(#134).
Screwlock
#134×2
Aperture-start Mg (#133)
#134×2 Adhesive: Screwlock
Aperture-stop Mg (#135)
Wire arrangement of each Mg and Soldering This website stores data such as cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You Yellow: Aperture start Mg may change your settings at any time or accept the default settings. Green: Aperture Aperture start Mg
Privacy Policy
Orange: Aperture stop Mg
Marketing
Blue: Aperture stop Mg
Personalization Analytics Save
Red: Mirror-drive Mg
Accept All
Black: Mirror-drive Mg
- Ａ10 ･
-
VBA13001-R.3677.A Mirror BOX unit Mirror unit I-base plate unit
・ Position #B211 in the direction of the arrow, and x it with three screws (#1525). ・ When the mirror unit (#10201) is mounted, adjust the horizontal clearance , if any, by washers
(#236A-E). ・ Connect the FPC of the I-base plate (#B71) to the Grease: LEN317A
#233
connector of #B1009.
#1523x2
#231 #1525 ×
#232
3
B10201
#229
#214
#343 #222
#10201
Direction for position
#B10212
#242
#1568
#210
#B211
#236A~Exn #960
This website stores data such as cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You may change your settings at any time #B71 or accept the default settings. #1523x2
Privacy Policy Marketing Personalization Analytics Save
#170
Accept All
#B1009
#1530
- Ａ11 ･
-
VBA13001-R.3677.A AF drive unit Horizontal-shooting Horizontal-shoo ting lever unit
・ Fix the AF drive-PCB unit (#328) with two screws (#1636). Be careful NOT to pinch the AFFPC. horizontal-shooting lever unit (#B355), turn the lever unit clockwise to apply ・While holding the pedestal of the horizontal-shooting compression to the spring. ・ Fit the groove part of the coupling shaft (#342) in the U-part of the horizontal-shooting lever unit (#B355), and tighten the screw (#1513).
・ Put the edge of the AF drive unit FPC into the hole of the I-base plate FPC, and make soldering bridges at four locations.
Grease: G-92KA
#342 #1513 #B355 #1636
#343x2
This website stores data such as cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You may change your settings at any time or accept the default settings.
#B328
#344x2
Privacy Policy Marketing Personalization Analytics Save
Accept All
- Ａ12 ･
-
VBA13001-R.3677.A Lens release SW Lens release unit Vertical lever SCM-change PCB
Grease: AX-115
Grease: G-92KA Grease: G-92KA
Apply to the front, back, and inner surface of the hole.
#66×3 Black Brown Red
#1516
#381
#1568 #1527
#979
#378
#1034
#380
#978 #356
#385
#1563
#1539×2
#386
#379
#377
#977
#357
△(Revise）
#382
Blue #1116
#359
#977.#978.#979
#384
This website stores data such as cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You may change your settings at any time or accept the default settings.
Oil barrier: OS-30MF
Grease: G-92KA
Privacy Policy Marketing Personalization
#376
Analytics Save
Accept All
#1654x2 #372
サービス #371
計画課
Ｍ - Ａ13 ･
Change page △ ×1
-
JUL.7.2006
VBA13001-R.3677.A Front cover unit Aperture coupling-ring unit Drysurf: AX-115
Bayonet
・ Assemble the aperture coupling-ring (#RP1) into the apron (#22), and attach the spring (#406) and roller (#407). Then mount this assembled assembled unit on the front body by turning slightly slightly clockwise, and x x it with two screws (#1514) and two screws (#66). Drysurf: AX-115
Oil barrier: OS-30MF #980
#40 #38×2 #37
#407
#388 #389
#1551 △(Addition） #773 #383
#26
Oil barrier: OS-30MF Apply to the holes on the back side.
#1514
#66
Be careful NOT to ・ be nd th e br us h of th e ap er tu re coupling-ring (#RP1). ・drop the roller (#407).
#22
#406
・dirt the pattern of the F-F0 PCB This website stores such as unitdata (#B1024). cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You may change your settings at any time or accept the default settings. Privacy Policy
#402 #401
#1621×4
Grease: G-92KA #RP1(404,405)
Marketing Personalization Analytics Save
#1620
Accept All
Caution: After mounting the bayonet, press the lens release-pin and conrm con rm that the pin moves smoothly without catching. サービス
計画課 - Ａ14 ･
Change page △ ×1
Ｍ
-
JUL.7.2006
VBA13001-R.3677.A Height adjustment of AF coupling shaft ① Set the SCM-change lever (#383) to "S mode". (AF coupling shaft (#342) protrudes from the bayonet face.)
② Adjust the height of the AF coupling shaft (#342) by using the screw (#359) to "1.7±0.2 mm". ③ After the adjustment, x the screw (#359) with Screwlock.
#383
1.7±0.2 mm
Bayonet surface
Lens-release pin
#359
Lens-release button
#342
#359
Apply after the adjustment Adhesive: Screwlock
Height adjustment of Aperture lever
( J18004). ・Measure the height of the aperture lever by using the tool (J18004). This website stores data such as cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You may change your settings at any time or accept the default settings.
Aperture lever
Privacy Policy Marketing
m m 5 ． ３ ～ 5 3 . ３
Adjustable screw
Personalization
Adhesive: Screwlock
Analytics Save
mm Standard：3.4±0.1 0.5
Apply after the adjustment
Accept All
- Ａ15 ･
-
VBA13001-R.3677.A Angle adjustment of Main mirror and sub-mirror
・Main mirror 45° adjustment Caution: ・Before and after the adjustment, check the accuracy by moving the main mirror up- and downwards a few times. ① Check for the right-left deviation. In case the deviation is out of standard, loose three screws (#1523) and make an adjustment by moving the main mirror shaft PCB (#B10212). for the up-down deviation. In case the deviation is out of standard, make an adjustment by turning the ② Check eccentric pin with Hexagonal wrench.
・Sub-mirror 59° adjustment Caution: Before and after the adjustment, check the accuracy by moving the main mirror up- and downwards a few times. Conrm if the two-pronged part part of the sub-mirror rmly ts in tthe he eccentric pin. ・ Check for the up-down deviation. In case the deviation is out of standard, make an adjustment by turning the sub-mirror eccentric pin. ＊ Device 1. For Main mirror adjustment ① Collimator (J19002) ② 45° mirror tool (J18389) ③ Mirror 45° inspection tool (J18037) ④ Hexagonal wrench (φ1.5mm） Main mirror shaft
2. For sub-mirror adjustment ① Collimator (J19002） ② Sub-mirror 59° inspection tool (J18391) ③ Hexagonal wrench (φ1.5mm）
#1523×3 Apply after the adjustment Adhesive: Screwlock
PCB (#B10212)
Collimator Mirror 45°checking tool
Bayonet mount
This website stores data such as J18389 cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You may change your settings at any time or accept the default settings. Main mirror
Eccentric pin for the main mirror
Mirror of J18391 Width of line indicates deviation. Sub-mirror
Privacy Policy
Eccentric pin for the submirror
Marketing Personalization
Main mirror
±15’ AnalyticsLeft-right deviation Up-down Save Accept All ±5’ deviation Distortion
Sub-mirror Up-down
±15’
6’or less
±15’ 6’or less
Reference line
Left-right
- Ａ16 ･
-
VBA13001-R.3677.A 10-pin plug 10-pin FPC unit V-groove comes in the lower right-hand corner (viewed from the ・Position the 10-pin plug (#41) so that the V-groove front), then t it in the holes of the back side of the 10-pin FPC (#1010), and assemble them into #26.
・ Apply Locktite to the screw (#65) and tighten it. ・ Fix the 10-pin FPC (#1010) with the screw (#1503). ・ Make soldering bridges of the 10-pin plug (#41) and 10-pin FPC at nine locations. ・ Make soldering bridges of 10-pin FPC (#1010) and lens contact-FPC at eight locations. ・ Solder six wires.
Red: Main PCB unit Black: Main PCB unit
#B1008 Blue: Lens release SW #1010
#1010
△(Revise）
Red: SCM-change PCB Brown: SCM-change PCB #1503
Black: SCM-change PCB #1010
#65
Adhesive: Loctite
This website stores data such as cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You may change your settings at any time Oil barrier: or accept the default settings.
#41
OS-30MF
Privacy Policy
#968
Marketing Personalization Analytics Save
Accept All
#26
V-groove サービス
計画課
Ｍ - Ａ17 ･
Change page △ ×1
-
JUL.7.2006
VBA13001-R.3677.A AF CCD FPC unit
・ Assemble the adjustment springs (#293) in the bottom of the mirror BOX unit (#B211).
・ Attach the AF CCD FPC unit (#B1007) with three Hexagonal-Key screws (#295). (#295). Then, turn lightly the the screws all all the way in, and
#B1009
△(Revise） then back them out two-and-half turns.
・ Connect the FPC of the AF CCD FPC unit (#B1007) to the connector of #B1009, and tighten the screw (#1507) together with the I-base plate FPC.
#295×3
#1507
#B1007 #B211
#293×3
This website stores data such as cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You may change your settings at any time or accept the default settings.
Privacy Policy Marketing Personalization Analytics Save
Accept All サービス
計画課 Ｍ - Ａ18 ･
Change page △ ×1
-
JUL.7.2006
VBA13001-R.3677.A Penta unit Prism box unit
・ Press #8 into #832. ・ Attach #1055, #833, and two #872 by positioning them.
*
・ If a gap is found in #1055, replace #877A by #877B. Taking g careful of up/down/front/back up/down/front/back direction, assemble #1055 and ・ Takin #833. Caution: Press #8 all the way into #832 until the one step lower position. Do NOT let the two #875 and #832 run off the edge of the frame.
#1619x2
Press-tting #8
#832
#B1005
#954 #875x2
#876
#B1005
Direction for position
#833
Direction for position
#953
#1055
#955
＃ 871
#840
#904
#837
#902
This website stores data such as #839 site cookies to enable essential functionality, as well as marketing, personalization, and analytics. You may change your settings at any time or accept the default settings.
#877A～B
#873x2
Direction for
Direction for
position
position #872x2
#874x2 #877C×2
#838x2
Privacy Policy Marketing Personalization
*
Analytics Save
#836A～C
#901
#834
#3
Accept All #835
- Ａ19 ･
-
VBA13001-R.3677.A Eyepiece lens-barrel unit
#5 #7
#845
Adhesive: Super X
Adhesive: Super X #841 #847
#841
Grease: AX-115
#7
#B846 #847
#B846
#844 #1539 #848
#849
#841 #856
Connect the nder-display
#853 #845
#854
FPC (#1004) to SI-FPC #5
(#1005).
#1539 #858
This website stores data such as cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You may change your settings at any#848 time #842 or accept the default settings.
#842
#1619x2
#1005
Align the grooves of #848 and #853.
#1004
Privacy Policy
#853
Marketing
#841
Personalization
#1618×2
#878
Analytics Save
#1054 #842 Accept must not protrude from #841. All
#879
- Ａ20 ･
-
VBA13001-R.3677.A Metering FPC unit
・ Fix the metering adjusting plate (#B882) with three screws (#1617). ・ Fix the metering FPC unit (#B1006) and three springs (#884) temporarily with three screws (#883). connector.. ・ Make a mountain fold of FPC, and hook Ａ -part to the SI-FPC (#1005), while Ｂ-part to the connector with two screws (#1525) (#1525) and two screws (#1528). ・ Fix the prism BOX unit with
・ Connect the lens contact-FPC (#B1008) to the connector Ｃ -part of the SI-FPC (#1006). #883×3 Attach the metering FPC unit. Turn lightly three screws
・
#B1006
Mountain fold
(#883) all the way in, and then back one reference screw of them out one three -and-halfturn. △(Revise）
Ｂ Ａ
#884×3
#1617×3
#B882 #995 Reference screw
#996
#1528×2
Ａ
Ｂ
#1 #1005 005
#1006
#1525×2 Ａ
Ｃ
#1005
This website stores data such as cookies to enable essential site functionality, as well as marketing, Ｃ personalization, and analytics. You may change your settings at any time or accept the default settings.
Ｂ
#B1008
Ｃ Ｃ
Privacy Policy Marketing Personalization Analytics Save
Accept All サービス サービ ス
計画課 Ｍ - Ａ21 ･
Change page △ ×1
-
JUL.7.2006
VBA13001-R.3677.A
3. Mount Front body on Rear body Mount the front body on the rear body
① Operate the charge-lever of the I-base plate unit (#B71) for mechanical reset. ② Check the connection status of the FPC (#1009).
③ While passing the two lead wires of the AF motor (#B26) into the hole of the rear body, assmeble the front body (by taking care NOT to pinch the wires but
Orange Blue
Charge lever Grease: G-92KA
to pull them.)
④ Tighten the ve screws (#1575) in the order from ① #B71
to ⑤ .
⑤ Tighten two screws (#1531) in the order of ① and ② .
FPC #1009
⑥ Tighten the screw (#1525).
Check the
⑦ Tighten two screws (#1529) in the order of ① and ② .
insertion.
⑧ Tighten the screw (#67).
Rear body
#1531×2 ②
①
#1097 Orange :AF motor
#1525
#1098 Blue :AF motor
Front body
This website stores data such as cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You may change your settings at any time or accept the default settings.
①
① ② #1529×2
Privacy Policy
#67
Marketing
③
Personalization Analytics Save
Accept All
④ ⑤ ②
#1575×5
- Ａ22 ･
-
VBA13001-R.3677.A Inspection and Adjustment of Body back
＊ "0" positioning of the dial gauge
0" position of D200
5 0
6 0
7 0
9 0
4 0 3 0
8 0
2 0
1 0
0
2 0
1 0
Surface plate
①
Put the tool (J18001-1) on the surface plate, and set the dial gauge to "0".
direction of the arrow, and shift the posit position ion by "0.17 mm" from 0 that was set in ② Turn the index ring in the direction ① . (This is "0"-position of D200.)
③
Measure the body back based on "0" reference position of the index ring.
This website stores data such as 4 parts from the bayonet face to the CCD-PCB ・Measure cookies to enable essential site functionality, as well as marketing, attaching face. personalization, and analytics. You may change your settings at any time Standard:48.5±0.015mm/ 015mm/ Parallelism: within 0.015mm Standard:48.5±0. or accept the default settings. ・In case it is out of standard, make an adjustment Privacy Policy by loosening screws that that attach the front and rear Marketing bodies, or by putting the washer(s) washer(s) on the contact surface between the front body and rear body. body. Personalization
Analytics Save
Accept All
Measuring points Measure the outside angle of view.
- Ａ23 ･
-
VBA13001-R.3677.A Grip unit
・ Fix the grip (#57) with the screw (#1515) and two screws (#1509).
#826 #952 #952
#58
#1517
#1515 #828 #1559 #829 #1509
This website stores data such as cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You may change your settings at any time or accept the default settings.
Privacy Policy Marketing Personalization Analytics Save
Accept All
#1509
#439 #57 #769
#1541
- Ａ24 ･
-
VBA13001-R.3677.A Main PCB unit
・ Solder two wires on the back side of the main PCB unit (#1001). ・ Connect the main connection-FPC (#1035) to the connector of the back side of (#1001). Back side of Main PCB (#1001)
Yellow: Power drive PCB Brown: Power drive PCB
FPC #1035
body, and x the main PCB unit (#1001) with three screws ・ Pass the FPC (#1035) through the hole of the rear body, (#1616).
・ Connect the ve FPCs to the connectors in the order of ① - ⑤ . Be careful NOT to forget to connect the FPC of ① . ・ Solder thirteen wires.
Black: Charge-SW Brown: Charge-SW Red: Charge-SW
Caution: 10-pin wires and buzzer wires must be put und under er the con convex vex por tio tion n of of the front of the prism. (see below)
Purple: Battery contact Blue：FG-ID
Black: Buzzer
Black: AF-assist illuminator
Black: Buzzer
Gold: AF-assist illuminator
②
Penta prism
This website stores data such as cookies to enable essential site functionality, as well as marketing, ④ You personalization, and analytics. may change your settings at any time or accept the default settings.
③
Black: 10--pin FPC Red: 10-pin FPC
Privacy Policy
Marketing
①
Personalization
②
⑤ △(Addtion）
Analytics
#1613×3
Yellow: Lens contact FPC
Save
Accept All
Brown: Lens contact FPC サービス
計画課 Ｍ - Ａ25 ･
Change page △ ×1
-
JUL.7.2006
VBA13001-R.3677.A AF motor wire arrangement
・ Arrange the AF motor wires by placing them properly among bosses at four locations. Put the power drive-PCB (#1002) into the rear body groove, and fx f x it with two screws (#1541).
・
Solder six wires.
・
Fix the conductive plate (#688, #689, and #690) with three screws (#1539).
・
Fix the conductive plate (#691) with the screw (#1543).
・
#1541
Brown: Main PCB Yellow: Main PCB
Put #1002 in the groove. Black: Charge motor Red: Charge motor
Blue: AF motor
#1541
#1539
Orange: AF motor
Power drive PCB (#1002) △(Addtion）
This website stores data such as cookies to enable essential site Conductive plate functionality, as well as marketing, personalization, and analytics. You (#689) may change your settings at any time or accept the default settings.
#1035
△(Addtion）
#1002
Privacy Policy Marketing Conductive plate Personalization (#690) Analytics Save
Accept All
#1539
#1539
#1539
#1543 Conductive plate (#688) #1539
Conductive plate (#691)
△(Revise）
サービス
計画課 - Ａ26 ･
Change page △ ×3
-
JUL.7.2006
VBA13001-R.3677.A DC/DC PCB unit
・ Connect the harness (#1075) to the DC/DC PCB (#1047) and the connector of the power drive PCB (#1002). ・ Fix the DC/DC PCB (#1047) with four screws (#1541). ・ Solder six wires.
Wire arrangement Battery contact wire
Charge motor wire AF motor wire
Harness connection
#1 #1047 047 #1075
#1002
Black: Battery contact
#1541
This website stores data such as cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You may change your settings at any time or accept the default settings.
Red: Battery contact
#1541
Yellow: SBDI-PCB SBD I-PCB
Privacy Policy
Brown: SBDI-PCB
Marketing Black:IF-PCB
Personalization
Red: IF-PCB
Analytics Save
Accept All
#1541 #1541
- Ａ27 ･
-
VBA13001-R.3677.A Inspection and adjustment of AE CCD Alignment
＊ Under the environment where the AE-CCD positioning is adjusted, use the reference body (and change the envoronment depending on measured results). ・ In case the measured value is out of standard, check if there is no misalignment of the grid lines. of standard, change the environment environment of measurements. (e.g. setting place/ ・ In case the measured value is out of direction, room brightness, etc) Procedure ① ② ③ ④ ⑤ ⑥ ⑦
Fix the bottom cover with four screws. Mount "AF50/1.4D" on the camera, and x them on the tripod horizontally. horizontally. Connect the camera and PC via the cable (MC-31). Provide power to camera by the AC adapter (EH-6).
＊ Be careful NOT to cause a short-circuit at uncovered portions. Attach the AE-CCD positioning positioning tool (J15427) in the color viewer (J63070), and turn power ON. Keep the 0.7-m distance between the front face of the AE-CCD positioning tool and the reference surface of the camera. Set the camera AF AF to manual, and the focus ring to to "0.7 m" by rotating it. Start up the inspection and adjustment software for D200 (J18397), and select "INSPECTION AND ADJUSTMENT FOR AECCD POSITION" then "Set Camera for AE CCD POSITION". Looking through the viewnder viewnder,, and and move the camera sso o that the grid lines of the camera coincide with the extension lines of the AE-CCD positioning tool. tool. (Turn "d2: Grid Disp Display" lay" of Custom menu to ON.)
horizontally. ＊ Set the camera and AE-CCD positioning tool horizontally. Select "CCD ALIGNMENT INSPECTION AND ADJUSTMENT". ＊ Cover the camera with a black cloth, etc, when measured. ⑨ By following instructions on PC, make the position adjustment of AECCD by the screws (a:#883,b:#883). INSPECTION” of the adjustment softw software are and make an inspection. Then, x the ⑩ Select “CCD SLANT INSPECTION” three screws with Screwlock slightly slightly.. The adjust adjustment ment is completed. completed.
⑧
Attaching surface of the imaging-PCB
AE-CCD positioning tool (J15427)
・ Attach the metering FPC unit. Turn lightly three screws (#883)
AF 50/1.4D approx. 0.7 ｍ
all the way in, and then back one reference screw screw of them out one
△(Revise）
This website storesthree-and-half data such as turn, and adjust by the screwsite (a. and b.). cookies to enable essential functionality, as well as marketing, Standard → Reference screw personalization, and analytics. You X-direction → a: Screw may change your settings at any time or accept the defaultY-direction settings. → b: Screw Privacy Policy Ｘ -direction (a) loosening Marketing
Color viewer (J63070)
Adhesive: Screwlock
(#B1006) Metering FPC unit
Y-direction (b) loosening
b:#883
Personalization Analytics Save
Accept All
a:#883
Ｘ direction (a)
Y direction (b)
tightening
tightening
サ
Reference screw
ビス
計画課
Ｍ - Ａ28 ･
Change page △ ×1
-
JUL.7.2006
VBA13001-R.3677.A
Outer LCD window / Shoe mold unit / Accessory shoe / Other small parts Apply the grease to the inner surface.
#502 I S O
W B Q U A R
Grease: G-92KA
#501
#1026 #516 #503 #318 #1640×2 #316 #504 #507 #1533
#B317
#512
#701
#511
Adhesive：C-8008B Align the four corners of two sponges (#766)
#324
twoand sponges (#765), attach This websiteand stores data suchallas #B735 the corners. cookies to enable essential site functionality, as well as marketing,#1605 Do NOT let the inner personalization, and analytics. You sponges run off the edges may change your settings at any time of the frame. #766×2 or accept the default settings.
#327 #323 #1565 #765×2
#731
Privacy Policy Marketing
#1540×2
#1560
Personalization Analytics Save
#747
#753
#750
#1537×2
Accept All
#1606
#746 #1547×2
Apply to the claw.
Grease: G-92KA
- Ａ29 ･
-
VBA13001-R.3677.A Release button / Other small parts
Apply to shaft.
#732
Grease: G-92KA Apply to the overall back side.
Apply overall.
#733
Oil barrier: OS-30MF
#734 #742
#743 Apply overall.
#24
Grease：G-92KA Direction for assembling.
#701
Apply to about two screw threads. Adhesive: Loctite
#B43
#787
This website stores data such as cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You may change your settings at any time #1659 or accept the default settings.
#1659 Apply to entire circumferential surface.
#RP5
#730
#911
Adhesive: C8008B
Privacy Policy #966 Marketing Apply
overall. Personalization
Analytics Save
#1557×2
Oil barrier: OS-30MF #1652
#1604
#748×2
Accept All #1608×2
#749 Grease: G-92KA Use ink brush to apply.
#967×2 #968
Oil barrier ：OS-30MF Apply to
- Ａ30 ･
＃
967, and #968 overall.
-
VBA13001-R.3677.A Top cover FPC unit Mount the rear command dial unit (B726).
・
Tighten two screws (#1571).
・
Solder the rear command dial unit (B726) at three locations.
・
Mount the front command dial unit (B725).
・
Tighten two screws (#1544).
・
Solder the front command dial unit (B725) at three locations.
・
Make soldering bridges at nine locations.
・
#1544 × 2
Soldering bridge
B725
#B725 はんだ
#704 B726
#707×2 #1544×2
#1571
#1053 #973 #706 #705
#781
#321×4
#780
#974 #39 #1003
#784 This website stores data such as #914 #1028 cookies to enable essential site #B782 functionality, as well as marketing, #1117(Red) personalization, and analytics. You #1119(Black) may change your settings at any time #1118(Brown) or accept the default settings. #1535
#913
#703
#912 #965
Privacy Policy
#781
Marketing
#780
Grease: MZ-800S
Personalization Grease: Analytics
Apply to the clicking part of
MZ-800S
Save
#1544×3
#784
Accept All
#929 #B726
#784. #1571×2
#1033
- Ａ31 ･
-
VBA13001-R.3677.A Ｍ／ＤＦＰＣ部組 ・B502,B50 ・B502, B504( 4( 三つ葉 三つ葉釦部組 釦部組 ) を取り を取り付ける 付ける。 。 ・FPC ・F PC を持 を持ち上 ち上げビ げビス ス #1 #157 572 2 を締 を締める める。 。 追加） ） ・#1094 シンクロターミナルコードのはんだ付 シンクロターミナルコードのはんだ付けをする。 けをする。※ △( 追加 ・#1025 ・#102 5 をボスに差 をボスに差し込む。 し込む。 ・ビス ・ビ ス #1 #156 569 9 を締 を締める める。 。 ・#1025、#10 ・#102 5、#1026 26 の FPC はんだブリ はんだブリッジをはん ッジをはんだ付けを だ付けをする。 する。 69
三つ葉釦部組
んだ ブリッジ
#1026 はんだ箇所 △( 追加 追加） ）
#1025
ス 1572
Green#1094 Green #1094:SB :SB 基板 ボス
オイルバリア：OS-30MF
シンクロターミナ ル部のはんだ付け は２ 以 に こ なってください。
I S O Q U A R
1026FPC
#B504
#50
#B43
This website stores data such as cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You may change your settings at any time or accept the default settings.
513 #1532
#46
1025FPC
Marketing
#514
#510 #1544 × 2
#515
Analytics
#1569 #B505
Save
#508 #509
Privacy Policy オイルバリア：OS-30MF
Personalization
油：G-92KA
Accept All #1569
#1572
#1569
径 5 ミリ ミリヘク ヘクスキ スキー使 ー使用 用
サ
ビス
計画課
Ｍ 差し替えペー 差し替 えページ△× ジ△× 2
Ａ32 ･
-
Aug.8.2006
VBA13001-R.3677.A SB lower case unit Dipping
Grease: AX-115
・ Assemble #796, #322, and #325. #796×2 △(Revise）
#796 #325
#322
#796
・ Insert the collar (#308). ・ Insert the rotation axes (#306 and #307). ・ Mount the SB lower case unit (#B302) on the top cover. ・ Pass wires through the holes.
Pass six wires through the holes.
Dipping
Wire arrangement
#B302
Grease: AX-115
#307
Hooks
#308 Be careful of the direction for assembling.
This website stores data such as #306 Grease: AX-115 cookies to enable essential site functionality, as well as marketing, SB-up spring personalization, and analytics. You may change settings at anyspring time (#305) to the hooking part. Attach the SB-up ・your or accept the default settings. ・ Fix the SB-up spring (#305) with the screw (#1601).
#305
Privacy Policy Marketing Personalization
#305
Analytics #1601
Save
Dipping
Accept All
サービス
計画課 Ｍ
Hooking part Change page △ ×1
- Ａ33 ･
-
JUL.7.2006
VBA13001-R.3677.A Installment of Top cover FPC / Wires / SB-PCB
・ Tighten the screw (#1541). ・ Tighten the screw (#1535). ・ Tighten the screw (#1511). ・ Attach the FPC of the SB-PCB （#B1013). ・ Tighten the screw (#1601). ・ Solder seven lead wires of the SB-PCB.
#1511 #1535 FPC
#B1013
#1541
SB-PCB (Orange) SB-PCB (Gray) SB-PCB (Black) SB-PCB (Green) SB-PCB (Red) Sync terminal (Green) SB-PCB (White) #1601
・ Solder the three metering lead FPC lead wires. Solderdata the four shoe-contacts. This website such accessory as ・stores cookies to enable essential site functionality, as well as marketing, Black personalization, and analytics. You may change your settings at anyBrown time Accessory shoe contact×4 or accept the default settings. Red
・The tape is applied.
Privacy Policy Marketing Personalization Analytics Save
△(Addtion）
Accept All
サ
ビス
計画課 - Ａ34 ･
Change page △ ×1
-
JUL.7.2006
VBA13001-R.3677.A Assembly of Top cover unit SB lock cover Oil barrier: OS-30MF
#917C #310 #309 #312
・ Attach #309. ・ Attach the spring (#310).
#1565
SB upper case
While sliding the SB lower lower case (#301) downw downwards, ards, attach its two hooks to the holes. (Fig.1)
・
・
Tighten Tighten two screws screws (#1623). (Fig.2)
SB upper case Hooks
#301
Fig.1
This website stores data such as cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You may change your settings at any time or accept the default Holessettings. #1623×2
Privacy Policy
Pop-up lever unit
Marketing Personalization Fig.2
Analytics Save
Accept All
SB lower case unit
- Ａ35 ･
-
VBA13001-R.3677.A Top cover Eyepiece frame
・ Fix the eyepiece frame unit (#861, #963, and #903) with two screws (#1619). ・ Connect the top cover FPC (#1003) to the connector of the main PCB unit (#1001).
#1001
#1003
#1039
Oil barrier: OS-30MF #963
This website stores data such as cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You may change your settings at any time or accept the default settings.
#1619×2
#903
#861
Privacy Policy Marketing Personalization Analytics Save
Accept All
- Ａ36 ･
-
VBA13001-R.3677.A Top cover Diopter adjustment knob
・Fix the top cover with two screws (#1511), three screws (#1555), two screws (#1547), the two screws (#1548). (#851, #857, and #852) with the screw (#1622). Then attach the cover ・Fix the diopter adjustment knob unit (#851, (#850).
＊ After attaching the top cover, turn the diopter adjustment knob to check the operations of the diopter adjustment lens. Pop SB up. #1548×2
#1511
#1511
#1555
#1555
This website stores data such as cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You may change your settings at any time or accept the default settings.
#1555 #1547
#1547
Privacy Policy Marketing Personalization Analytics Save
#851 #857 #852
Accept All #1622
Oil barrier: OS-30MF Apply to teon surface side.
#850 #850
- Ａ37 ･
-
VBA13001-R.3677.A Accuracy inspection and and adjustment (Camera body) ★ : Newly prepared RJ
Commercially available straight cable
To RS232C terminal Stabilized power supply Set value ＝ 7.4V 0.3Ω 5.0A or AC adapter EH-6
★ J18397 D200 inspection and adjustment software
Battery tool J15423
Use [9pin-25pin] conversion connector for a
★
computer with 9-pin RS-232C terminal. RJ is not available, so use a commercial item.
＊ Note: When checking “battery check”, be sure to use the battery tool (J15423). When this tool is used, LCD indications of camera disappear. disappear.
Flash meter Not prepared as RJ
Shutter tester J61199 Light receiving adapter (in common with D100)
This website stores data such as cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You may change your settings at any time or accept the default settings. J19042E T.V.measuring adapter (APS) EF-8000
Privacy Policy
★ AE-CCD J15427 Set up in front of color viewer (J63070)
Marketing Personalization Analytics Traditionall adapter for camera Traditiona
Save
Accept All
★ AF28/2.8D AF50/1.4D
When Ｍ 1/8000 is adjusted, use the T.V.measuring adapter (APS) EF-8000(J19042E) and the light receiving adapter (J61199).
Caution: When the inspection and adjustment are made with the shutter tester, turn the tester ON to light a lamp, and carry out the aging for 3-5 minutes.
- Ａ38 ･
-
VBA13001-R.3677.A
D200 Inspection and Adjustment Software (J18397) This inspection and adjustment software runs on Windows. Windows. Install the software by following the below procedure. <Operating environment> Check the following operating environment which is required for installing this program on PC. PC OS CPU RAM (memory) HD Moni Mo nito torr re reso solu luti tion on In Inte terrfa face ce
IBM PC/AT compatible Windows XP XP Professional E Ed dition, W Wiindows XP XP Home Ed Edition, Windows2000, Windows 98 Second Edition (SE) 80486 100MHz ～ Penti Pentium um 4 2.2GHz 32MB or more 6MB-or-more free disk space is required when installing 800× 800×60 600 0 pixels or more Seria eriall iint nter erfa facce ((sw swiitcha tchabl blee ffrrom COM1 to COM9) M9)
※ USB interface is not available.
As long as the above hardware requirements are met, any PC such as desktop or laptop, etc is available.
＜ Cautions in starting program ＞ When starting this program, close all the other applications. If some other applications are running, this program may not be activated.
<Procedure for installation> The le (D200SOFT.EXE) (D200SOFT.EXE) of this program is provided via FD or e-mail. Because this is the self-extracting le, decompress the le before installing, following the next procedure.
1. Create a folder for installation under a name you like and PC drive.
This website stores data such as (e.g.) C:\D200 cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You may change your settings at any time or accept the default settings.
Privacy Policy Marketing Personalization Analytics Save
Accept All
- Ａ39 ･
-
VBA13001-R.3677.A 2. Paste the le (D200SOFT.EXE) in the created folder.
3. Double-click on the pasted le to display the following screen. Press the OK button, then decompression starts.
This website stores data such as 4. When the decompression of le is nished, the le (D200.EXE) is created. cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You may change your settings at any time or accept the default settings.
Privacy Policy Marketing Personalization Analytics Save
Accept All
5. The installation is completed. - Ａ40 ･
-
VBA13001-R.3677.A <Start-up of Program> 1. Double-click the le (D200.EXE), then Inspection and adjustment program for D200 starts.
2. To display in Japanese, select the radio button "JAPANESE" in "LANGUAGE" in the lower right-hand corner of the screen.
However, this is not properly viewed in the English OS.
This website stores data such as cookies to enable essential site " (communication port), the selection from “COM1” to “COM9” is available. 3. For "COM PORT" PORT functionality, as well as marketing, personalization, and analytics. You may change4.your settings at any time button at the lower-left is pressed, the program version will be displayed. When the "HISTORY" or accept the default settings.
Privacy Policy Marketing Personalization Analytics 5. Select each item button according to operation. Save
Accept All
Follow the instructions on the next screen that will be shown after pressing the item button.
6. To nish the program, press the Close (×) button in the right-hand corner of the screen or QUIT QUIT.. .
- Ａ41 ･
-
VBA13001-R.3677.A AE inspection and adjustment inspection and adjustment (ref. Page A28for details details） ① AE CCD alignment inspection ② AE accuracy inspection and adjustment ③ Aperture accuracy inspection ④ M1/8000 Accuracy inspection and adjustment ⑤ Adjustment for battery check level (Use the battery tool (J15423) and stabilized power supply.） * Check & Adjust an out put of Built-in Speed light,after assembling until Rear cover. ⑥ Built-in SB ash inspection and adjustment
〔Tools required〕ref. Page A38. ・AE accuracy inspection and adjustment For this camera, the AE shift amount, which is fundamental for other lenses, is adjusted by using the AF28/ 2.8D lens. Check in advance, by "INSPECTION for AF28mm/1:2.8D LENS." on the main menu, whether the adjustment AF28/2.8 AF28/2.8 D lens is available. When checking the lens, measure by using the reference body (used for the shooting image adjustment, too), using the adjustment AF50/1.4D lens, and using the adjustment AF28/2.8D AF28/2.8D lens. When inspecting and adjusting the AE accuracy, make an adjustment by combining the adjustment AF50/ 1.4D lens, which was conrmed by "INSPECTION for AF2 AF28mm/1:2.8D 8mm/1:2.8D LENS." and the adjustment AF28/ 2.8D lens. ・"Battery check" inspection When the battery tool (J15423) is connected, the indications indications of the outer LCD of this camera disappear disappear.. After adjusting "Battery check", inspect by the software by powering to camera at 7.8V 7.8V.. ・Built-in SB ash inspection and adjustment Set the distance between camera and ash meter to 1 m, and inspect and adjust the light volume of the built-in SB. (ref. adjustment software for details) AF inspection and adjustment Note: When using using the adjustment software software for the rst time, prepare 3 cameras of D200 an and d measure by "WRITING OF AF ADJ. LENS OFFSET V VALUE" ALUE" on the main menu. AF accuracy inspection and adjustment (Make all the following adjustments.)
① ② YAW, PITCH inspection and adjustment ③ LARK adjustment (inc. CCD output adjustment) This website stores data such as ④ AF shift adjustment cookies to enable essential site functionality, as well as marketing, 〔Tools 〕 You personalization, andrequired analytics. may change1.your settings at any When adjusting fortime all adjustment items or accept the default settings. ref. Page A38.
2. When inspecting AF accuracy Privacy Policy ① AF adjustment lens (J18266)
② AF adjusting tool (J15259） ③ Lens holder for F4 (J15280) Personalization ④ AF chart（J18344 ） Analytics ⑤ Chart illuminator for AF（J15264） 3. When W hen adjusting a djusting YAW YAW, PITCH P ITCH Marketing
Save
Accept All
YAW, PITCH tool（J18230） 4. When adjusting LARK
The above tool when inspecting AF accuracy In "AF shift adjustment", the distance from the bayonet reference plane to the imaging area (CCD) is calculated by the actual shot photo, photo, and its error is recorded in EE EEPROM PROM as compensation amount amount,, and adjusted. - Ａ42 ･
-
VBA13001-R.3677.A ・ Solder four wires that are connected from the SB-PCB. ・ Arrange four wires by positioning them towards the front body, and attach the tape (#930).
SBDI-PCB: #1029 Red: SB-PCB Black: SB-PCB
Yellow: SB-PCB Brown:SB-PCB
Tape (#930)
CF card holder
・ Connect the CF-DG connection-FPC (#1038) to the CF card holder (#1018). ・ Pass the CF-DG connection-FPC (#1038) through the hole of the body, and x it with three screws (#1543). #1543×3
This website stores data such as cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You may change your settings at any time or accept the default settings.
Privacy Policy #1018 CF card holder
Marketing Personalization Analytics Save
Accept All
サービス
△(）
#1038
計画課
△(Addtion）
- Ａ43 ･
Change page △ ×2
Ｍ
-
JUL.7.2006
VBA13001-R.3677.A CCD/FPC unit
・ Position the CCD/FPC unit (#B2032) towards the direction of the arrow, and x it with three screws (#1639). ・ Connect the harness SZ (#1073) and harness AK (#1074) to the DC/DC-PCB (#1047). wires. (ref. Fig) ・ Solder the four shielding wires. Solder the GND line of the shielding wire on the outer soldering lands of
・
the CCD-PCB CCD-PCB (#B2032). (See below)
A
C Ｃ
１１２７
Ａ
×2
D
Ｄ
B Ｂ
外側のランド
Core wire (coated) ＧＮＤ側 GND line
Fig
#1639×3
This website stores data such as cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You may change yourHarness settingsSZat(#1073) any time or accept the default settings.
Position
Harness AK (#1074) #B2032 CCD/FPC unit
Note: For some bodies, bodies, washer(s) are already put on the attaching attaching face of the CCD-bracket. There are 2 cases as follows. Privacy Policy 1. Purpose：To adjust the height of the camera body Marketing There are indications by color marker (washer thickness) on the camera body side of the CCD-PCB attachPersonalization ing face. Analytics {One red marking marking =0.02mm (#534), Two red markings ＝ 0.04mm (#534×2)}
* The position, position, number, etc of of washers washers are not the same at 3 locations. Save Accept All ＊ By adding the measured value to the thickness of washers, check if it is within the standard (48.5±0.015mm). 2. Purpose：To adjust the height of the CCD bracket
There are indications by blue marker (doughnut shaped) of the CCD-bracket attaching face
{One marking at upper right corner ＝ 3 locations ＝ 0.01mm}* Washers Washers are equally put on the 3 locations. ＊ When the CCD PCB is replaced, remove the washers. - Ａ44 ･
-
VBA13001-R.3677.A DG-PCB unit ・ Solder the GND line on G-side of the DG-PCB (#B1017). (There are "S" and "G" letters on the DG-PCB) shield wire on A, B, C, and D. (ref. Fig) ・ Solder each shield
A
C １１２７
D
×2
B
Core line (coated)
ＧＮＤ側 GND
Fig.
・ Mount the DG-PCB unit (#B1017). four shield wires. (ref. Fig. ) ・ Solder the four connector. ・ Connect two harnesses to the connector.
Tape (#926)
・ Put the ferrite core in the CCD FPC. ・ Connect the four FPCs to the connectors. ・ Attach the tape (#926). ・ Put the shield wires under the viewnder view nder for arrangement. This website stores data such as cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You may change your settings at any time or accept the default settings.
Privacy Policy
#926
Marketing
#B1017 (DG-PCB unit)
Personalization Analytics Save
Accept All
Harness Harness
- Ａ45 ･
-
VBA13001-R.3677.A DG shield plate Fix the DG-shield plate plate with fve screws (#1546) and two screws (#1515).
・
Make soldering bridge.
・
#1515
#1546×5
DG-shield plate unit
#771 GASKET △(）
Soldering bridge
#1515
I/F cover Assemble the conductive plate (#695) by aligning with the boss.
・
Position the I/F cover towards the top cover, and fx it with two screws (#1510). (#1549)
・
△(）
This website stores data such as cookies to enable essential site functionality, as well as marketing, #969 personalization, and analytics. You may change your settings at any time or accept the default settings. #962×3
#392
#961
Privacy Policy
#394 #393
Marketing Personalization #1642×2
Analytics Save
Direction for position
#395
Accept All #695
#1643
#1510×2
#1510×2
サービス
△(）
- Ａ46 ･
Change page △ ×3
計画課 Ｍ
-
JUL.7.2006
VBA13001-R.3677.A #467 #1538 × 2
#985,#986
#RP00007
Oil barrier ：OS-30MF
#985
#481
#469
#474 #468
#986
Grease:G-92KA
Grease:G-92KA
#455
#476
Grease:G-92KA
#465
Direction for position
#426
#475 Crazy glue Grease:G-92KA
Crazy glue
#1511 × 2 #1630
#1631
This website stores data such as cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You #472 may change your settings at any time or accept the default settings.
#478
#477 #456
#479 #1020
#473
Privacy Policy Marketing
#1511 × 2
#470
Personalization #430
Analytics Save
Accept All #480
#422
- Ａ47 ･
#1512 × 3
-
VBA13001-R.3677.A #431 #433
#434,#435 Oil barrier ：OS-30MF
#434 × 2 #435 × 2
#488 #1057 #1626
Grease:G-92KA
#489 Direction Grease:G-92KA
#1629
for position
#487
#1633
Grease:G-92KA
#492
#484
#432 #483 × 2 #485 #1546
#440 #491
#440 Oil barrier ：OS-30MF
This website stores data such as cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You may change your settings at any#427 time or accept the default settings.
#1571 #987
#486
#987 Oil barrier ：OS-30MF
#1632 × 2 Grease:G-92KA
#1518 × 2
#921
Privacy Policy Marketing
#441
#425
Personalization
#922 #445
Analytics Save
Accept All #443 #429
#424
#442 #423
#442,#921,#922,#923,#441 Oil barrier ：OS-30MF
#1628 × 2 #923
- Ａ48 ･
-
VBA13001-R.3677.A Rear cover Connect the three TFT-PCB TFT-PCB connection PCBs to the DG-PCB connectors.
・
・ Fix the rear cover with two screws (#1547), two screws (#1552), and one screw (#1549).
This website stores data such as cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You may change your settings at any time or accept the default settings.
Privacy Policy
#1552×2
Marketing Personalization Analytics Save
Accept All
#1549
#1547×2
- Ａ49 ･
-
VBA13001-R.3677.A Bottom cover ･ Mount the bottom cover. ･ Tighten two screws (#1556), six screws (#1549), and two screws (#1547). ･ Attach the battery lid.
#1547
#1547 Bottom cover
#1549×6 #1556
#1556
∞ Innity focus inspection & adjustment
・Replace the nder screen with the innity focus check screen (J18394), and use the reference lens (J18010) and read the value. In case it is out of standard, standard, increase or decrease washers (#836A, (#836A, #836B, or #836C) for adjustments. * Supply the power (Battery or or EH-6) for checking.
Caution: When (J18394) is put in to replace the nder screen, put it with the silver spacers upward, which are attached on both sides. Standard: ±0.04mm Standard: ±0.04mm 0.01mm） 1 scale ＝ 0.01mm ） This website stores data such as "0" position J18010 cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You may change your settings at any time or accept the default settings.
Privacy Policy
Reference line
Marketing
Value of J18010 +0.04 ～ -0.04 +0.05 ～ +0.07 +0.08 ～ +0.14 +0.15 ～ -0.05 ～ -0.07 -0.08 ～ -0.14 -0.15 ～ -0.17 -0.18 ～
Adjustment Within standard, adjustment unnecessary Replace with #836C Replace with #836A Remove the washer . Replace with #836A, #836C Add #836A Add #836C Add #836B
Personalization Analytics Save
Accept All
#83 836A 6A #836B #836C
1K602 K602-8 -832 32 1K602-833 1K602-840
Scr cree een n was ashe herr A 0.10mm Screen w waasher B 0.20mm Screen w waasher C 0.15mm
- Ａ50 ･
-
VBA13001-R.3677.A External rubber
･ Attach the external rubbers (#B63, #B60, #B61, and #B447). I S O
W B Q U A R
#B61
#447
#B63
#B60
This website stores data such as cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You may change your settings at any time or accept the default settings.
Privacy Policy Marketing Personalization Analytics Save
Accept All
- Ａ51 ･
-
VBA13001-R.3677.A
Necessary adjustments adjustments when parts are replaced 1. D200 adjustment adjustment softwa software re and updates
Adjustments EEPROM xed values
Parts to be replaced
AE CCD
AE accuracy
M1/8000
Aperture
positioning inspection & inspection & accuracy adjustment adjustment adjustment inspection
Battery
Built-in SB light volume
AF accuracy
check level inspection & inspection & adjustment adjustment adjustment
○
Shutter unit
＊1
Main FPC
○
＊2
△
○
○
○
○
○
○
Sub-PCB
○
AF sensor unit
Top cover or SB lower case unit
DC/DC PCB unit This website stores data such as cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You may change your settings at any time Metering FPC unit or accept the default settings.
○
○
○
○
○
Privacy Policy Aperture control PCB unit
Marketing
○
Personalization ＊ 1. When the main PCB unit is replaced, be sure to update the version before writing the xed values. Analytics ＊ 2. Make an inspection. Save Accept All
- Ａ52 ･
-
VBA13001-R.3677.A
2. Shooting image adjustment software and updates
Adjustments
Parts to be replaced
Writing of xed values
Gr/Gb difference
Sensi- Shading tivity
Gr/Gb com- Sensitiv pensation ity ratio
compensa-
adj. (R/B
tion ADJ (G
lter)
lter)
Pixel de- Pixel defect Rewriting of fect com-
compensa-
TFT xed
pensation -
tion -
data
Black
White point
Initial (factory default) setting
○
point
Shutter unit
Main PCB unit
AF sensor unit
DC/DC PCB unit
Metering FPC unit
＊1 DG PCB unit
CCD/FPC PCB unit
TFT monitor
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○ ○
This website stores data such as When thesite DG-PCB unit is replaced, be sure to update the rmware before writing the xed value. ＊１．essential cookies to enable functionality, as well as marketing, personalization, and analytics. You may change your settings at any time or accept the default settings.
Privacy Policy Marketing Personalization Analytics Save
Accept All
- Ａ53 ･
-
VBA13001-R.3677.A Shooting Image Adjustment 1. Summary
A53 △(） When D200 shooting image-related and listed parts on Page A51 are replaced, be sure to make an adjustment by the shooting image image adjustment software for D2 D200 00 (J65084). The details of its function function and how to use this this software are as follows: 2. Adjustment software function
(1) (2) (3) (4) (5) (6) (7) (8) (9)
Writin Writing g of xed values Gr/Gb difference compensation adjustment (G lter) "Sensitivity" adjustment Shading adjustment Gr/Gb compensation compensation adjustment adjustment (R/B lter) lter) / Line Line crawl adjustment adjustment "Sensitivity ratio" adjustment Pixel defect compensation - black point Pixel defect compensation compensation - white point Rewriting of TFT xed data
(10) Initial (factory default) setting (11) Getting reference values (12) Reading of RISC version (13) Checking of the adjustment value ※ When the adjustments from (2) to (6) are made, get in advance the reference values of (10) by using the reference body, then perform the adjustments. 3. Hardware requirements
OS： PC：
Widows98SE，Windows2000 ，WindowsME，WindowsXP Japanese or English OS CPU Pentium Ⅱ or more
Memory 128MB or more USB1.1 Screen size: 1024×768 pixels or more This website stores data such as 4. Howessential to set upsite cookies to enable Create any directory in the harddisc (except desk top) of PC, and copy the following les. functionality, as well as marketing, D200IMG.exe ・ ・・・・・ Application le personalization, and analytics. You STD.DAT Standard le ・ may change your settings at・・・・・・・ any time or accept the settings. NkdPTP.dll NkdPTP .dll・・・・・・ USB-communication application application extension le for W WinXP inXP default ・
NkdPTPDi.dll・・・・・ USB-communication application extension le for Win98SE and Win20 Win2000 00 ・ MPLP.dll・・・・・・・ ・ Privacy Policy
For system
MSVCP60.dll ・・・・・ For system (Win2000) (Win2000) ・ Marketing CCDFLG.DAT・・・・・Fixed value data (writing of xed values ） ・ Personalization CCDINIT.DAT Initial value data (factory default setting)
・ ・・・・ Analytics Q0220IMAGEADJUSTMENT67.dll・・・・・・For pixel defect compensation ・ LineCrawlFittingQ220DLL.dll ・・・ ・・・・・For line crawl, shading ・ Save ・ Accept All LineCrawlFittingQ220.ini initialization le for line line crawl ・・・・・・・・・・ System initialization LineCrawlFittingQ220G.ini ・・・・・・・・・ System initiali initialization zation le for G-line G-line crawl ・
System initialization le for shading LineCrawlFittingQ220SD.ini preserdata.jpg・・・・・・・・・・・・・・・Default setting WB image le ・ ※ Be sure to copy the above le in the same directory. Change page △ ×1
- Ａ54 ･
-
サービス
計画課
Ｍ JUL.7.2006
VBA13001-R.3677.A Procedure for installing USB driver If this program is used by the USB interface, installing the USB driver is necessary. But if the OS is "Windows XP", the driver is already preloaded so it is not necessary to install it.
(1) Set the USB USB of camera to "PTP".
(SETUP menu → USB setting → PTP) (2) Connect the camera and PC by USB cable. cable.
Turn camera ON. (3) When "Add New Hardware Wizard" is displayed, click "Next".
(4) Select "Search for a better drive than the one your device is using now. (Recommended (Recommended)", )", and click "Next".
This website stores data such as cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You may change your settings at any time or accept the default settings. (5) Click "Reference" of "Specify a location" and and select the directory where th thee driver was copied, such as Privacy Policy
"C: ¥D200¥PTP". ¥D200¥PTP". Then click click “Next”.
Marketing Personalization Analytics Save
Accept All
- Ａ55 ･
-
VBA13001-R.3677.A
(6) Conrm that the driver is located at the right right place, and click "Next".
(7) Click "Finish".
(8) Reboot the PC to complete the installation. This website stores data such as cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You may change your settings at any time or accept the default settings.
Privacy Policy Marketing Personalization Analytics Save
Accept All
- Ａ56 ･
-
VBA13001-R.3677.A
6. Basic usage (1) Perform the D200IMG.exe D200IMG.exe to start up the main sscreen. creen. (ref. Fig.1) JAPANESE in Language to display the expected menu. (ref. Fig.2) (2) Select ENGLISH / JAPANESE (3) Click the button to start adjustments. ※ When the adjustments from 2. to 6. are made, calculate to get the "Sensitivity" and "Sensitivity ratio" reference values of (7) by using the reference body beforehand, then perform the adjustments. (4) Follow the instructions on screen. To complete the procedure, click "QUIT" button or "Close" button at the upper-right corner of the menu. (5) To
Fig.1
This website stores data such as cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You may change your settings at any time or accept the default settings.
Privacy Policy Marketing Personalization Analytics Save
Accept All
Fig.2
- Ａ57 ･
-
VBA13001-R.3677.A 7. Required equipment and conditions ※ AC adapter EH-5 and USB cable (mini B type) UC-E4 are used for all adjustments so they are not specied in the list. Item 1 Writing of xed value 2 Gr Gr/G /Gb b dif diffe fere renc ncee
★ New established tool tool Setting/Remarks
Required device None ・5100K color viewer
J63070
compensation adjustment (G lter)
(ex-model viewer J63049 is also available.) ・Luminance meter BM-3000 J63068 aperture ) J61185 ・Tool lens (to x aperture) J63086 ・SP2 (G lter) 3 Se Sens nsit itiv ivit ity y adju adjust stme ment nt 5100K color viewer J63070 ・ (ex-model viewer J63049 is also available.) ・Luminance meter BM-3000 J63068 aperture ) J61185 ・Tool lens (to x aperture) ・ ND lter (ND8×1+ND4×1) 4 Sh Shad adin ing g adju adjust stme ment nt 5100K color viewer J63070 ・ (ex-model viewer J63049 is also available.) ・Luminance meter BM-3000 J63068 aperture ) J61185 ・Tool lens (to x aperture) ・ ND lter (ND8×1) 5 Gr/G Gr/Gb b co comp mpen ensa sati tion on J63070 ・5100K color viewer (ex-model viewer J63049 is also adjustment (R/B lter) available.) / Line crawl adjustment ・Luminance meter BM-3000 J63068 ・Tool lens (Fixed aperture) J61185 ・SP3 (R lter) J63087 ・SP1 (B lter ） J63085 6 Sen Sensit sitivi ivity ty ratio ratio adjust adjustmen mentt ・ 5100K color viewer J63070 (ex-model viewer J63049 is also available.) This website stores data such as cookies to enable essential site ・Luminance meter BM-3000 J63068 functionality, as well as marketing, aperture ) J61185 ・Tool lens (to x aperture) personalization, and analytics. You 7 Pix Pixel el def defect ect compen compensat sation ion - ・5100K color viewer J63070 may change your settings at any time (ex-model viewer J63049 is also black point or accept the default settings. available.) ・Luminance meter BM-3000 J63068 Privacy Policy aperture ) J61185 ・Tool lens (to x aperture) 8 Pix Pixel el def defect ect compen compensat sation ion Marketing white point Personalization 9 Rewriting of TFT xed data 10 Get etttin ing g of of rref efer eren ence ce val values ues Analytics
Body cap or lens cap None Sa Same me as "S "Sen enssit itiivi vity ty adj adjustm ustmen ent" t"
Save 11 Initial (Accept default)All sseetting
None
12 Checki Checking ng of of adj adjust ustmen mentt value value None None 13 Reading of of RI RISC ve version None
Equivalent to luminance LV13 Aperture F8
Equivalent to luminance LV13
Aperture F8 52 mm， Use the packaged product; 5-step light reduction Equivalent to luminance LV13 Aperture F5.6 Use the packaged product; 3-step light reduction Equivalent to luminance LV13
Aperture F8
Equivalent to luminance LV13
Aperture F8; No lter Equivalent to luminance LV13
Aperture F5.6 Environmental temperature approx. 20 - 25℃ No lt lter er when when se sen nsi siti tivi vity ty rati ratio o reference value is calculated.
- Ａ58 ･
-
VBA13001-R.3677.A 8. Summary
The summary on each adjustment is as follows: (1) Writing of xed values Because the xed value that is written in Repair Parts is blank, write the xed value when the DG-PCB is replaced.
(2) Gr/Gb difference compensation adjustment (G lter) Camera is faced to the light-emitting box (color viewer) of L LV13 V13 equiv. equiv. with SP2 (G lter) being put between them, and the adjustment adjustment is made so that the difference difference between Gr and Gb o output utput of the center (425×425 pixels) can fall in the standard range. G-line crawl (3895×2610 pixels) is divided into (29×25) blocks, and the difference between Gr and Gb output can fall in the standard range.
(3) Sensitivity adjustment Camera is faced to the color viewer of LV13 equiv. equiv. with ND lter (-5 steps) being put between them, and the adjustment is made by changing the ampgain so that G output can fall in the standard range. The gain value is adjusted so that the G output average value (A (Average verage of Gr/Gb) in the center (425×425 pixels) can reach the target output level (approx. 1040LSB). The actual adjustment of the gain value is made only under the condition of ISO100 and ISO1600, and the medium sensitivity is calcul calculated ated by the adjustment values of these 2 conditions. For target output level, G output average of sensitivity reference value (ISO100) is used, which was calculated by the reference body. (4) Shading adjustment (5100K color viewer is shot by this camera, and adjustment is made.) Camera is faced to the color viewer of LV13 equiv. equiv. with ND lter (-3 steps) being put between them, and the adjustment of white white balance distribution distribution is made for 3 areas [Area ① : Central 1936×1926-pixel area; Area ② : All the divided areas except ③ -areas after dividing (3890×2606-pixels) (3890×2606-pixels) into (29×25-pixels); Area ③ ; 4 corners of (4×6-pixels) after dividing (3890×2606-pixel) into (29×25-pixels)]
Area ①
Area ③
Area ③
4x6
4x6 Area ②
This website stores data such as 29x25 cookies to enable essential site 1936x1926 functionality, as well as marketing, Area ③ personalization, and analytics. You 4x6 may change your settings at any time or accept the default settings. (5) Gr/Gb compensation adjustment (R/B lter) / Line crawl adjustment
Area ③ 4x6
Camera is faced to the light-emitting box (color viewer) of LV LV13 13 equiv. equiv. with SP3 (R lter) or SP1 (B lter) being put between them, and the the adjustment is made so th that at the difference in G ou output tput average between MarketingB-G line and G-R line, when the whole screen is divided in areas, can fall in the standard range.
Privacy Policy
Personalization (6) Sensitivity ratio adjustment Analytics Camera is faced to the color viewer of LV13 equiv., equiv., and the adjustment is made so that the R/G, B/G outputAccept becomes Save Allthe same as the output ratio of the sensitivity ratio reference value that was calculated by
the reference body. body. The adjustment is made only under the condition of ISO100, and the average value of the center (425 pixels × 425 pixels) is used.
- Ａ59 ･
-
VBA13001-R.3677.A (7) Pixel defect compensation - black point When pixels of which the output level is under specied value with LV13 equiv., are detected, the coordinates of the detected pixels are rewritten as pixel defect compensation data.
(8) Pixel defect compensation - white point Shots are taken on the dark surface. In case the pixel output is found to be beyond the standard value, the detected pixel coordinate is additionally written as the pixel defect compensation data.
(9) Rewriting of TFT xed data
When TFT moniter is replaced, replace d, be sure to perform “REWRITING “REWRIT ING OF TFT FIXED DAT DATA”.
(10) Getting of reference values ・Sensitivity reference value calculation The reference body is faced to the color viewer of LV13 equiv. equiv. with the ND lter (-5 step) being put between them. Then, store the G output average average value of the center (425 pixels pixels × 425 pixels) is st stored ored in the STD.DAT le as the sensitivity reference value. Sensitivity ratio reference value calculation ・ The reference body is faced to the color viewer of LV LV 13 equiv equiv.. (without lter). Then, the sensitivity ratio reference value GR and GB is calculated, based on the G/R/B output average of the center (425 pixels × 425 pixels), pixels), and they are stored in the STD.DA STD.DAT le.
It is necessary to calculate the reference values of "Sensitivity" and "Sensitivity ratio" in order to prevent the color temperature uctuation caused by color viewer's changes over time from affecting the results of the shooting image adjustment. By using the reference body body,, calculate the reference values once in about every 3 months, when the uorescent of the color viewer is replaced.
(11) Initial (factory default) setting
By reset the settings of camera, factory default settings are restored.
Select the language and video mode to perform. This website stores data such as cookies to enableBecause essential site this setting of RP DG-PCB is blank, be sure to set the initial setting when the DG-PCB is replaced. functionality, as well as marketing, When this setting is used, the USB mode is set to "Mass Storage" mode. personalization, and analytics. You may change your settings at any time or accept the default settings. (12) Checking of adjustment value The adjustment value is conrmed, functioning as substitute for the traditional "READING AND Privacy Policy
REWRITING OF EEPROM DATA.".
Marketing
(13) Reading of RISC version Personalization Analytics The RISC rmware version is displayed. Save
Accept All
- Ａ60 ･
-
VBA13001-R.3677.A 9. Procedure 9-1. Shooting image adjustment
● Calculate the "Sensitivity" and "Sensitivity ratio" reference values by using D200 reference body beforehand, then perform the adjustments. adjustments. (ref. 9-5.)
● When the DG-PCB is replaced, perform all the shooting image adjustments from (1) to (6), and in other cases, perform those from (2) to (6) in this order. The adjustments from (1) through (3) are all programmed to be executed in serial order. When (1) is completed, the software automatically goes on to the next adjustment.
● In case adjustments are interrupted by NG, the adjustments can be continued again after NG. As for adjustments that were ended with OK, the ashram-up of the adjustment value is completed. possible without resetting "Custom setting" setting" of this camera. ＊ Note: Adjustments are not possible Before the adjustments, record the details of "Custom " Custom setting" set by customers if necessary. necessary. Start adjustments Provide the power for the camera via AC adapter. adapter. ・
・ Reset "Custom setting". Set "PTP" mode by Setup menu. ・ Set the focus mode to M, exposure mode to M, and the exposure compensation to "0" of the camera. ・ Connect the camera and PC via USB cable. ・ Set the color viewer luminance to LV13 equiv. ・
(1) Writing of xed values Click "1. WRITE FIXED VALUE TO EEPROM" on the menu. ・ The adjustment starts. When it is completed, "OK" "OK" is displayed. ・ The software automatically goes on to the next adjustment item. ・ (2) Gr/Gb This website stores data difference such as compensation adjustment (G lter) cookies to enable essential site COMPENSATION ADJ (G FILTER)" of the main menu on screen. Click "2. Gr/Gb ・ functionality, as well as marketing, Attach the tool lens (Aperture F8) and SP2 (G lter) to the camera. ・ personalization, and analytics. You Get the camera ・ may change your settings at anyclosest time to the center of the illuminated surface of the color viewer. or accept the The settings. adjustment starts. When it is completed, "OK" "OK" is displayed. default ・ The software automatically goes on to the next adjustment item. ・ Privacy Policy
(3) Sensitivity adjustment Marketing Click "3. SENSITIVITY ADJUSTMENT" ADJUSTMENT" of the main menu on screen. ・ Personalization Attach the tool lens (Aperture F8) and ND lter (ND 8× 1+ ND 4 ×1）to the camera. ・ Analytics Get the camera closest to the center of the illuminated surface of the color viewer. ・ The adjustment "OK" is displayed. Save ・ Accept Allstarts. When it is completed, "OK" The software automatically goes on to the next adjustment item. ・
- Ａ61 ･
-
VBA13001-R.3677.A (4) Shading adjustment Click "4. SHADING ADJUSTMENT" on the menu. ・ ・Attach the tool lens (Aperture F5.6) and ND lter (ND 8× 1) to the camera. Get the camera closest to the center of the illuminated surface of the color viewer. ・ The adjustment starts. When it is completed, "OK" "OK" is displayed. ・ The software automatically goes on to the next adjustment. ・
(5) Gr/Gb compensation adjustment (R/B lter) Click "5. Gr/Gb COMPENSATION ADJ (R/B FILTER)" on the menu. ・ Attach the tool lens (Aperture F8) and SP3 (R lter) to the camera. ・ Get the camera closest to the center of the illuminated surface of the color viewer. ・ The adjustment starts. When it is completed, the next instructions are displayed. displayed. ・ Attach the tool lens (Aperture F8) and SP1 (B lter) to the camera. ・ Get the camera closest to the center of the illuminated surface of the color viewer. ・ The adjustment starts. When it is completed, "OK" "OK" is displayed. ・ The software automatically goes on to the next adjustment. ・
(6) Sensitivity ratio adjustment Click "6. SENSITIVITY RATIO RATIO ADJUSTMENT" ADJUSTMENT" of the main menu on screen. ・ Attach the tool lens (Aperture F8) to the camera (without lter). ・ Get the camera closest to the center of the illuminated surface of the color viewer. ・ The adjustment starts. When it is completed, "OK" "OK" is displayed. ・ 9-2. Pixel defect compensation - black point Set the color viewer luminance to LV13 equiv. ・ Provide the power for the camera via AC adapter. adapter. ・ Reset "Custom setting". ・ Set data "PTP" mode ・ This website stores such as by Setup menu. cookies to enable essential sitemode to M, exposure mode to M, and the exposure compensation to "0" of the camera. Set the focus ・ functionality, as well as marketing, Connect the camera ・ personalization, and analytics. You and PC via USB cable. may change your settings at any POINT" time Click "BLACK of "PIXEL DEFECT COMPENSATION" of the menu. ・ or accept the default settings. Attach the tool lens (Aperture F5.6) to the camera (without lter). ・ Get the camera closest to the center of the illuminated surface of the color viewer. ・ Privacy Policy When the adjustment starts, pixel defects are detected, displaying the number of pixels and addresses. ・
After conrming the above, click "X" button. ・ Marketing When it is completed, "OK" is displayed. ・ Personalization The software automatically goes on to the next "WHITE POINT" of "PIXEL DEFECT COMPENSATION". COMPENSATION". ・ Analytics (After the black point compensation, be sure to perform the white point compensation, too.) Save＊ Note: InAccept All NG occurs due to dusts some cases, dusts on the CCD.
Be sure to clean the CCD surface before adjustments.
- Ａ62 ･
-
VBA13001-R.3677.A 9-3. Pixel defect compensation - white point Check the environmental temperature (approx. 20-25°C.). ・ Provide the power for the camera via AC adapter. ・ Reset "Custom setting". ・ Set "PTP" mode by Setup menu. ・ Set the focus mode to M, exposure mode to M, and the exposure compensation to "0" of the camera. ・ Connect the camera and PC via USB cable. ・ Click "WHITE POINT" of "PIXEL DEFECT COMPENSATION" of the menu. ・ Cap the camera with the body cap or lens cap to shield light from the mount. ・ When the adjustment starts, pixel defects are detected, displaying the number of pixels and addresses. ・ After conrming the above, click "X" button. ・ When it is completed, "OK" is displayed. ・ 9-4. Getting of of reference values Set the color viewer luminance to LV13 equiv. ・
・ Provide the power for the camera via AC adapter. Reset "Custom setting". ・ Set "PTP" mode by Setup menu. ・ Set the focus mode to M, exposure mode to M, and the exposure compensation to "0" of the camera. ・ Connect the camera and PC via USB cable. ・ Select "SENSITIVITY, RATIO REFERENCE VALUE CALC" of the menu on screen. ・ The current reference value is displayed on screen. ・ Click "SENSITIVITY, RATIO REFERENCE VALUE CALC". ・ The calculation of the sensitivity sensitivity reference value starts. The message to set conditions is displayed. ・ Attach the tool lens (Aperture F8) and ND lter (ND 8× 1 ＋ ND 4 ×1）to the camera. ・ Get the camera closest to the center of the illuminated surface of the color viewer. ・ Thedata adjustment ・ This website stores such as starts. When it is completed, the software goes on to the sensitivity ratio reference value. cookies to enable essential site lens (Aperture F8)(Remove ND lter). Attach the tool ・ functionality, as well as marketing, adjustment starts. When it is completed, the sensitivity and sensitivi sensitivity ty reference values are stored in ・The personalization, and analytics. You may change yourthe settings at any timele (STD, DAT). standard setting or accept the default settings. ・After this procedure, when the shooting image adjustment is made, the sensitivity and sensitivity ratio that were calculated this time are used. Privacy Policy ※ Calculate the sensitivity and sensitivity ratio reference values once in about every 3 months, and when the Marketing uorescent of the color viewer is replaced. Personalization 9-5. Reading of RISC version Analytics
Provide the power Save ・ Accept All for the camera via AC adapter. Set "PTP" mode by Setup menu. ・ Connect the camera and PC via USB cable. ・
Click "READING OF RISC VERSION" of the menu on screen. ・ RISC version is displayed. ・ - Ａ63 ･
-
VBA13001-R.3677.A 9-6. Procedure for upgrading RISC rmware: directory. ・ After preparing the CF card, copy the latest version ( XXXX. BIN) into the root directory. Insert the CF card, and select "FIRMWARE "FIRMWARE VERSION" from the SETUP menu. ・ Follow the instructions instructions on screen for version up upgrading. grading. It takes approx. 3-4 minutes. minutes. ・ Check the version of rmware by "RISC VERSION" of the image adjustment software. ・ Note: In case incorrect les are included in the CF card, the details for upgrading are not displayed even after selecting "FIRMWARE VERSION" from the SETUP menu.
＜ Measurement of Consumption current value ＞ When this camera is used for measuring the consumption current value, set the MB-D200 and wire as follows:
7.8V 0.3Ω
－
＋
－
＋ Ａ
This website stores data such as cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You may change your settings at any time or accept the default settings. Test item
MB-D200
Main SW・OFF All operational buttons are NOT pushed. Main SW・ON (Half-release timer OFF) Main SW・ON (Half-release timer O N) N) Marketing Main SW・ON (Illumination ON) Personalization Main SW・ON (TFT ON)
Privacy Policy
Analytics Save
Accept All
Standard
Test condition
200 μ A or less ref. above. 200μA or less 380 m A or less 400 m A or less 500 m A or less
AF50/1.4D、EV12
- Ａ64 ･
-
VBA13001-R.3677.A Black
Aperture Stop Mg
Mount
Red
Black
Soldering bridge
Soldering bridge
Black Mirror-up Mg
Brown
Yellow
△( 訂正）
Black
Zeabra pressure welding welding
Blue ﾚﾝｽﾞ着脱SW受け板 Lens release SW Plate
Aperture start Mg
Red
Blue
Black
AF motor Yellow
Connected with this connector
Orange
Connected with this connector
Brown
Connected with this connector
Shutter unit
Sync terminal
Yellow
実体配線図 WIRING
Orange
Green
Red
Brown Main condenser
Soldering Soldering bridge bridge
Connected with this connector
Connected with this connector
Green
Blue
AF assist illuminator
Connected with this connector
Purple
Red
Red
Black
Black
Soldering bridge
Gray
Brown
Black
Green
Red
Built-in Flash
Yellow
Brown
White
Connected with this connector
Red
Zeabra pressure welding
Soldering bridge
Brown Yellow
Black
Connected with this connector
Connected with this connector
Connected with this connector
Red
Connected with this connector
Brown Soldering bridge
Blue
Black
Orange
Brown Connected with this connector
Connected with this connector
Connected with this connector
Zeabra pressure welding (back side)
Connected with this connector
Connected with this connector
Charge motor Connected with this connector
DC-IN teminal
Blue Connected with this connector
VIDEO-OUT teminal
Connected with this connector
Red Black
USB terminal Connected with this connector
Connected with this connector
Orange
Connected with this connector
Blue Connected with this connector
Connected with this connector
Battery contact
Connected with this connector
Black
Purple
サービス
Red Brown
Black
Red
計画課
Ｍ
Yellow
- E1 -
差し替えページ△× 1 Change Page △× 1
JUL.7.2006
VBA13001-R.3677.A
工 具・TOOLS This website stores data such as cookies to enable essential site functionality, 工具番号 as well as marketing, personalization, andNo. analytics. You Tool may change your settings at any time J1 J 15427settings. or accept the default
★：新規設定工具・NEW
名 称
備 考
Name of tool
Others
AE CCD 位置出し工具 AE CCD positioning tool
★
Privacy Policy J18394 Marketing ★ Personalization
無限合致調整用スクリーン Innity focus adjustment screen
Analytics J1 J 18389 ★ Save
J1 J 18397
反射ミラー Accept All
Reection mirror カメラ部点検、調整ソフト
TOOL
Inspection and adjustment software for CAMERA
★
J65084
撮像部点検、調整ソフト Inspection and adjustment software for
★
IMAGING J1 J 18230
ＹＡＷ、ＰＩＴＣＨ工具
FOR F5,F100,F90,F90X,D70,D
Yaw,Pitch adjustment tool J1 J 15259
70s.D50
ＡＦ調整工具台 AF adjusting tool
J1 J 15280
Ｚレンズ用支持ホルダー Lens holder
J1 J 15264
高周波タイプ蛍光灯器具 Illumination box for AF adjustment
J1 J 18266
ＡＦ調整用Ｚレンズ（１ｍ用）
FOR F5,F100,D70,D70s.D50
Z adjustment lens (For １m） J1 J 15274
J15264 用チャートボード Chart board for J15264
J1 J 18344
ＡＦチャート
FOR D100,D70,D70s.D50
AF adjusting chart
- T1 ･
-
VBA13001-R.3677.A ★：新規設定工具・NEW
This website 工具番号 stores data such as cookies to enable site Toolessential No. functionality, as well as marketing, J19002 personalization, and analytics. You may change your settings at any time or accept the default settings.
J1 J 18391 Privacy Policy ★ Marketing
J18004
備 考
Name of tool
Others
縦型焦点面検査機 LT-500S Back focus collimator LT-500S
サブミラー５９°出し工具 Sub mirror angle adjustment tool
Personalization J1 J 18037 Analytics Save
名 称
オプチカルパラレル Optical parallel Accept All
絞りレバー高さ点検工具
Ｊ 19110 usabl usable e Ｊ 1911 19110 0 でも でも代用 代用可 可
TOOL
Aperture lever positioning gauge
J1 J 19004-1
インジケータ及びスタンド （ボディバック台、ゲージ） Dial indicator and Stand
J1 J 18001-1
ボディバック出し工具 Body back focus gauge
J19001
無限合致コリメーター F=600mm Collimator F=600mm
J18010
無限大合致基準レンズ
50/1.8
Innity Standeard Lens 50/1.8
J19042E
Ｔ秒時測定アダプター Ｔ秒時測定アダプタ ー (APS)-(EF80 (APS)-(EF8000 00 用） T.V. MEASURING ADAPTER (APS) (For EF8000)-(AP EF800 0)-(APS)(EF8 S)(EF8000 000 用）
J61199
D100 AE 受光部アダプター 受光部アダプター D100 LIGHT RECEIVE ADAPTER
J19123
シャッタ－試験機 ＥＦ－ 1（ＣＥ） Shutter Tester EF-1（CE）
FOR D100,D2H,D2X
共立電機製 KYORITSU ELECTRIC ＥＦ -8000 usable
- T2 ･
-
VBA13001-R.3677.A ★：新規設定工具・NEW
TOOL
This website 工具番号 stores data such as cookies to enable site Toolessential No. functionality, as well as marketing, personalization, and analytics. You J18267 may change your settings at any time or accept the default settings.
名 称
備 考
Name of tool
Others
Privacy Policy J6 J 61185
撮像関係調整用レンズ D1 Standard lens
FOR D1,D2H,D70,D70s,D50
ＮＤフィルタ－８Ｘ ND lter 8X
FOR D2H,D70,D70s,D50
Marketing
ＡＦ５０ ＡＦ ５０／１ ／１． ． ４Ｄ Lens AF50/1.4D
Personalization
J1 J 18191 Analytics Save
Accept All
J18358
ＮＤフィルタ ND lter 4X
J63070
カラービュワー Color Viewer
J63068
4Ｘ
1 枚使用 It uses by one pieces
輝度計（BM-3000） Luminance Meter BM-3000
J6 J 63085
ﾌｨﾙﾀｰ SP1 (75X75MM) Filter SP1 (75X75MM)
FOR D2H,D70,D70s,D50
J6 J 63086
ﾌｨﾙﾀｰ SP2 (75X75MM) Filter SP2 (75X75MM)
FOR D2H
J63087
ﾌｨﾙﾀｰ SP3 (75X75MM) Filter SP3 (75X75MM)
FOR D2H,D70,D70s,D50
J15423
電池工具 Battery tool
J19109
ＭＣ－３１（接続コード） ＭＣ－３１ (CONNECTING CORD)
★
- T3 ･
-
VBA13001-R.3677.A ★：新規設定工具・NEW
工具番号 This website stores data such as Toolessential No. cookies to enable site functionality, as well as marketing, OS-3and 0MF analytics. You personalization, may change your settings at any time or accept the default settings.
名 称
備 考
Name of tool
Others
LEN317A Privacy Policy
グリース ＬＥＮ３１７Ａ
ドライサ－フ ＯＳ－３０ＭＦ DRY SURF OS-30MF(OIL BARRIER)
Grease LEN317A
Marketing EDB0011 Personalization
ネシ゛ロック（赤）1401C Screw lock 1401C
Analytics
C-8008B Save
Accept All
セメダイン ８００８（黒） Cemedain 8008(BLACK)
TOOL
MZ 800S
ドライサ フ ＭＺ DRY SURF MZ-800S アロンアルファ Crazy glue
汎用品
フラッシュメーター Flash Meter
汎用品
デジタルマルチメータ Digital meter
汎用品 RJ is Not available
ＡＣアダプター ＥＨ－６
製品転用
AC adapter adapter EH- ６
RJ is Not available
ＵＳＢケーブル ＵＣ－Ｅ４ USB cable UC-E4
製品転用
パーソナルコンピュータ
汎用品
Personal computer
RJ is Not available
安定化電 安定 化電源（ 源（10 10 Ｖ
★
★
Privacy Policy Marketing Personalization Analytics Save
Accept All
RJ is Not available
RJ is Not available
5Ａ)
RJ is Not available
汎用品
Power supply(10V 5A)
RJ is Not available
へクスキー（φ 1.5mm） へクスキー（φ 1.5mm） HEX.KE HEX .KEY Y WRENCH WRENCH ( φ 1.5mm) 1.5mm)
汎用品
へクスキー（φ 5.0mm） へクスキー（φ 5.0mm） HEX.KE HEX .KEY Y WRENCH WRENCH ( φ 5.0mm) 5.0mm)
汎用品
ＡＦ２８ ＡＦ ２８／２ ／２． ． ８Ｄ
製品転用
Lens AF28/2.8D
RJ is Not available
This website stores data such as cookies to enable essential site functionality, as well as marketing, personalization, and analytics. You may change your settings at any time or accept the default settings.
８００Ｓ
- T4 ･
RJ is Not available
RJ is Not available
-
