Voip

Published on May 2016 | Categories: Types, Books - Non-fiction | Downloads: 43 | Comments: 0 | Views: 168
of 33
Download PDF   Embed   Report

Fundamental of voice over internet protocil

Comments

Content

Voice over IP

first-step
Kevin Wallace

© 2006



Cisco Press



Voice over IP First-Step



1587201569

What You Will Learn
After reading this chapter, you should be able to
✔ ✔ ✔

Explain the differences between various types of telephone switches. Describe the operation of traditional telephony systems. Identify the advantages of a Voice over IP (VoIP) network.

CHAPTER 1

Touring the History Museum of Telephony
Welcome to the world of Voice over IP (VoIP)! Think of it, sending your company’s voice traffic (or even your home’s voice traffic) over a data network. When you place a call from your office to New York or Los Angeles, your voice travels across your company’s network links, not through the telephone company’s voice network. As a result, you avoid long-distance charges; however, that’s just the tip of the iceberg. This book introduces you to the plethora of benefits VoIP offers. Prior to getting into the nuts and bolts of VoIP, you need to have a firm understanding of traditional telephony networks. This chapter takes you on a tour through the history of telephony. Traditional telephony components introduced in this chapter are compared and contrasted in later chapters with today’s VoIP components, providing you with the distinctions necessary to begin the migration to this exciting new world of telephony.

4

Chapter 1: Touring the History Museum of Telephony

Dissecting a Telephony Network
When you pick up your home phone’s handset and place a call to a friend, many operations occur in the background. This section walks through a basic phone call step by step, assuming you have a regular analog phone. note
Traditional analog phones are called POTS devices. POTS stands for “Plain Old Telephone Service.”

When you pick up the handset of your phone, you hear a dial tone in the receiver, and you can press keys on the touch-tone keypad to dial digits. However, on close inspection of your phone, you notice that there doesn’t seem to be a battery in the phone, and it’s not being powered from an alternating current (AC) wall outlet. So, the question is, “Where is the phone getting its power?” The answer is the phone company. The telephone switch at the phone company’s central office (CO) applies -48 volts of direct current (DC) across the wires coming out of the telephone wall jack. That voltage enables the phone to dial digits or even illuminate the keypad (in case you need to dial in the dark), for example. note
The telephone jack in the wall of your home (assuming you live in North America) is an RJ-11 jack, where RJ means Registered Jack. This RJ-11 jack has up to six conductors, although a phone that has only a single line uses just two of these wires.

You dial your friend’s phone number of 555-1212. The tones created from the digits you dial travel over a pair of wires leaving your phone, into your RJ-11 wall jack, and back to the telephone switch at your local CO. These two wires leaving your phone are called the tip and ring wires.

Dissecting a Telephony Network 5

note
Did you ever notice that in the movies or on television, almost all phone numbers begin with 555? That’s because originally, there were no residential or business seven-digit phone numbers in the North American Dial Plan beginning with 555. (Although some numbers outside the 555-0100 through 555-0199 range are now released for actual assignment.) Examples include 555-1212 for the Brady Bunch’s home and 555-0267 for the Townsend Agency in Charlie’s Angels. (It doesn’t work. I tried.) The producers don’t want to create another situation like the one caused by the song “Jenny.” Remember, eight six seven five three oh nine.

The names tip and ring come from the plug used by the operators of yesteryear to interconnect calls. As you can see in Figure 1-1, the plug used by these operators resembles the plug you might use to connect your headphones to your home stereo equipment. There are three conductors on this plug. The conductor (that is, wire) connected to the tip of the plug is called the tip, and the conductor connected to the ring in the middle of the plug is called the ring.
Figure 1-1 Tip and Ring
Ring

Sleeve

Tip

The tip and ring wires take on a new name after they leave your home. The connection from your home to the local CO is called the local loop. When your dialed digits, carried over the local loop, reach your local CO, the local loop connects into a phone switch. As the name suggests, a phone switch is responsible for interconnecting the endpoints (that is, the phones) that make up a phone call. The phone switch can recognize the digits you dialed by listening to the tones generated by your telephony keypad, or by interpreting pulses generated by a rotary phone. The phone switch can then determine to where your call should be

6

Chapter 1: Touring the History Museum of Telephony

forwarded, based on those dialed digits. If your friend lives just across town, perhaps your friend’s phone connects into the same CO that your home phone connects to. If that’s the case, then the phone switch sends ringing voltage over the local loop connecting to your friend’s home. If your friend does not live nearby, then the phone switch might need to forward your call to a phone switch in a different CO. A connection from one phone switch to the other is called an interoffice trunk. Your friend’s phone begins to ring, and he picks it up. Your friend’s local CO telephone switch notices that he picked up his phone’s handset and stops sending ringing voltage. At this point, you and your friend can begin to talk with one another. This chapter digs deeper into the inner workings of the phone call just described. For example, several types of signaling occurred to make the phone call possible. When you heard the dial tone and your friend heard his phone ringing, that was information signaling. When you dialed digits, that was address signaling. Figure 1-2 illustrates some of the components that make up a traditional telephony network.
Figure 1-2 Components of a Telephony Network
CO Trunk Interoffice Trunk Local Loop

Company PBX

CO Switch

CO Switch

Home Phone

The list that follows defines the traditional telephony network components illustrated in Figure 1-2:
■ ■

Edge devices (for example, phones)—Connect into a telephony network. Local loops—Connect callers to a local CO over a pair of wires called tip and ring.

The Public Switched Telephone Network: The Phone System That You Grew Up With 7



Phone switches—Make it possible for one phone to connect to another phone by dialing a phone number. The switch interprets the dialed digits and interconnects the dialing phone’s local loop with the destination phone’s local loop. Trunks—Interconnect phone switches. Unlike a local loop, a trunk typically transports multiple simultaneous conversations.



The preceding example considered a phone switch located in your local CO. However, for businesses, that is not always the case. Businesses might have their own phone switches. The next few lessons in this chapter compare and contrast these various types of phone switches, beginning with phone switches that make up the public switched telephone network (PSTN).

The Public Switched Telephone Network: The Phone System That You Grew Up With
The telephone that Alexander Graham Bell invented in 1876 did not have a touchtone keypad. Nor did it have a rotary dial. In fact, for decades after the invention of the telephone, many callers could not directly dial the person they wanted to speak with. They first had to speak with an operator and ask the operator to connect them with the desired party. You have probably seen this scene played out on the Andy Griffith Show. Andy picks up the receiver on his phone in the sheriff’s office and asks Sara to connect him with Floyd’s Barber Shop. Andy didn’t have the option of dialing Floyd directly. This was standard operation for the phone system until a Kansas City undertaker became fed up. Back in 1889, an undertaker named Almond Brown Strowger was losing business because the local Bell Telephone operator had a brother-in-law who was a competing undertaker. So, when someone called the operator wanting to speak with an undertaker, guess who they were connected with? That’s right, the Bell Telephone operator’s brother-in-law.

8

Chapter 1: Touring the History Museum of Telephony

note
Different accounts of the story suggest relationships between the operator and the competing undertaker other than brother-in-law/sister-in-law (such as cousin or spouse). However, the various versions of the story do depict a close family relationship between the operator and the competing undertaker.

Mr. Strowger thought that callers should be able to call him directly, without a meddling operator. This frustration led to his invention of the first telephone switch. This switch, through a series of mechanical relays, could interpret a caller’s dialed digits and form a pathway between the calling party’s phone and the called party’s phone. The Strowger Switch, also known as the Step-by-Step Switch, was adopted by AT&T in 1924 and was in widespread use in the United States into the 1980s. Today’s CO telephone switches are digital, as opposed to the mechanical Strowger Switch, and these switches are connected in a hierarchical manner. Your home phone probably connects to a Class 5 CO (that is, your local CO), which then connects up to a Class 4 CO, and so on. This hierarchical approach of interconnecting telephone offices minimizes the number of interoffice trunks required to connect all of the nation’s telephones together into what is called the PSTN. The structure of the PSTN is composed of three different types of networks:


Local Network—Local networks typically include local loop connections that provide a path for businesses and homes to connect back to their local central office. Exchange Area Network—Exchange area networks typically interconnect local exchanges (for example, Class 5 offices) and tandem exchanges (for example, an office that can act as an intermediary point, when two other switches do not have an available trunk between themselves). Long-Haul Network—Long-haul networks typically interconnect local exchanges (for example, Class 5 offices) with long-distance offices.





Private Branch Exchanges: How Big Businesses Talk 9

Private Branch Exchanges: How Big Businesses Talk
I used to work on the telephone system at a university, and the university had about 6000 telephones on campus. How much do you think it would cost for each one of those phones to have a direct connection back to the local CO? In those days (the early 90s), a business line had a recurring monthly charge of approximately $40. That comes out to $240,000 every month for local phone service for those 6000 phones! There must be a more economical approach. One such approach was for the university to have its own phone switch. That’s right. A private entity such as a business or university can have its internal phones connect to its own phone switch instead of the local CO. That private phone switch then connects to the local CO over a series of trunks (analog and/or digital, which are discussed Chapter 3, “Paving the Pathway to a Voice over IP Network”). The good news is that 6000 trunk connections back to the local CO were not required because statistically speaking, all 6000 phones would never be in use at exactly the same time. In fact, based on traffic studies (a topic covered in Chapter 2, “Making Waves: Turning Your Voice into Zeros and Ones”), we needed approximately 210 trunk lines (that is, voice paths) interconnecting the university’s phone switch with the local CO, as illustrated in Figure 1-3.
Figure 1-3 University Telephone System
210 CO Trunks

University PBX 6000 Telephones

Telephone Company CO

10

Chapter 1: Touring the History Museum of Telephony

Admittedly, there are other costs associated with having a private phone switch. For example, we had to pay a maintenance contract to have a technician onsite, and we had to purchase the phone switch itself (which was approximately $3 million back in the late 1980s). However, when considering the vast discrepancy in recurring monthly phone line charges, the economies of scale are clear. Assuming each of those 210 trunk lines costs $40 per month, the total monthly “phone bill” would be $8400. When compared with an earlier calculation of $240,000 per month, that’s a savings of $156,000 per month! Large businesses typically select private branch exchanges (PBXs) to act as their privately owned phone switches. PBXs are available in a wide variety of shapes and sizes and typically support 20 to 20,000 phones. Most PBXs are “featurerich,” offering voice mail, music-on-hold, call transfer capabilities, and many other features. However, the relatively large initial cost of a PBX might not give a smaller business a satisfactory return on investment (ROI). The alternative for a smaller business is an entry-level phone switch called a key system, as described in the following section.

Key Systems: How Small Businesses Talk
Smaller businesses only needing to support 30 to 40 phones might not be able to justify the purchase of a PBX system and instead might rely on another option called a key system. Like a PBX, a key system can act as a phone switch for phones within the organization and provide trunk lines back to the local CO for call destinations outside of the business. The distinction between a classic key system and a PBX is more than simply the number of supported phones. In a PBX environment, callers typically dial a 9 on the telephone keypad to access an outside line. In other words, after they dial a 9, they get a second dial tone. This second dial tone comes from the local CO. In a key system environment, because the number of lines (that is, trunk connections) going back to the local CO is relatively small, these lines are directly

Ringing, Dial Tone, and Other Bells and Whistles 11

accessible from the key system’s key phones. For example, you might be using a key phone with five line buttons. If you want to call outside of the local business, instead of dialing a 9 to access an outside line, you can press an available line button right on the key phone. You might have been visiting a car lot, as an example, and heard over the booming intercom, “Kevin, you have a call on line three. Kevin, please pick up line three.” In that instance, Kevin could go to one of the key system’s key phones, and press the line three button to access the call. However, if you have been in the market for PBXs or key systems lately, you have probably realized that the line between the two is starting to blur. More and more key systems are starting to feel very PBX-like. For example, these days, you might need to dial a 9 to access an outside line on your key system. These phone switches that have characteristics of both PBXs and key systems are sometimes called hybrid phone switches.

Ringing, Dial Tone, and Other Bells and Whistles
Earlier in this chapter, you considered an end-to-end telephone call between you and a friend. In passing, you learned that various types of “signaling” occurred during that phone call. The following sections examine the various types of signaling:
■ ■ ■

Supervisory signaling Address signaling Information signaling

12

Chapter 1: Touring the History Museum of Telephony

Supervisory Signaling
Supervisory signaling indicates to the phone switch whether a connected phone is currently on-hook or off-hook and also when a phone receives an incoming call. Supervisor signaling includes:
■ ■ ■

Loop Start Signaling Ground Start Signaling Ringing

Loop Start Signaling In a home environment, the phone switch in the local CO can determine whether a phone is on-hook or off-hook based on whether current is flowing over the local loop connecting back to that phone. Because an on-hook phone mechanically has its tip and ring circuit open, the -48 volts of DC applied across the tip and ring wires isn’t doing anything. The voltage is just sitting there, waiting for the circuit to close. After the handset goes off-hook, however, the tip and ring circuit is closed, and current can begin to flow through that circuit. When the telephone switch at the CO sees this current begin to flow, it knows that the phone has gone off-hook, and the telephone switch sends a dial tone to the caller, indicating that they can begin dialing digits. This type of supervisory signaling is called loop start signaling. Loop start signaling has an issue with glare. Did you ever pick up the phone to call someone, but you didn’t hear any dial tone and instead discovered that someone was on the other end of the line? If so, you experienced glare. Glare occurs when you beat the signaling and pick up your handset before your phone rings. What’s really spooky is when the person you were about to call is the person on the other end of the line! Glare may not be a major concern in a home environment, but what about a line connecting to a company’s PBX system? Because the lines connected to a PBX experience a significantly higher call volume than you do on your home phone (unless you have teenagers), the probability of glare occurring with a PBX using

Ringing, Dial Tone, and Other Bells and Whistles 13

loop start signaling is much higher than the probability of glare occurring on your home phone. Therefore, you often find another type of signaling used on PBX systems, and also on pay phones. That other type of signaling is ground start, and the good news is that ground start signaling prevents glare.

Ground Start Signaling With ground start signaling, the phone switch monitors the voltage potential on the “ring” lead of a line, and when the ring lead has a ground potential, the line is seized. If you watched the 1983 movie WarGames, you witnessed an example of ground start signaling. Do you remember the scene? Matthew Broderick’s character rides his bicycle up to a pay phone, but he doesn’t have any money. So, he takes the pay phone handset and bangs it against the pay phone’s chassis, which loosens the transmitter cover. He opens up the transmitter portion of the handset, pulls out one of the leads (the ring lead), and touches the lead to the chassis of the pay phone (which had a ground potential). By creating this off-hook ground start signal, he can place a call. note
Circuits in today’s pay phones prevent the falsification of ground start signals, as Matthew Broderick did in WarGames.

Ringing Ringing is also considered to be supervisory signaling. Ringing voltage is sent from the telephone switch to alert the destination phone that it is receiving an incoming call. Here is a fun experiment: the next time your home phone rings, start counting (one thousand one, one thousand two, …) to see how many seconds the ringing lasts and how many seconds of silence there are before the ringing begins again. In the United States, the pattern of ringing, called the ring cadence, is two seconds on and four seconds off, as Figure 1-4 illustrates. However, it seems that Hollywood isn’t that patient. If a phone rings on a TV show or a movie, most of the time, they use a much shorter ring pattern (typically, one second on and two seconds off).

14

Chapter 1: Touring the History Museum of Telephony

Figure 1-4

Ringing Pattern Examples
0.4 Seconds of Ringing

2 Seconds of Ringing

2 Seconds of Silence

4 Seconds of Silence

0.2 Seconds of Silence

United States Ringing Pattern

United Kingdom Ringing Pattern

Pop quiz time! Who invented the telephone ringer? This is a question that I ask students in my classes, and the most popular answer is Alexander Graham Bell. However, it was Thomas Watson, Mr. Bell’s assistant, who invented the mechanical ringer. Back in those days, the copper wiring over which the voice traffic and ringing voltage was sent wasn’t manufactured to the quality standards that today’s transmission is. As a result, Thomas Watson used significant voltage to go across this lower quality medium to cause a mechanical ringer to ring. Specifically, the original ringer required 75 volts of AC. Because today’s signaling might be communicated over fiber optic cable, and the ringers are rarely the mechanical kind, you might assume that such high voltage levels would not be necessary. However, the tradition of using higher voltages for ringing is still observed today in the PSTN, which is why you shouldn’t touch bare telephone wires. Another mystery of ringing voltage goes back to an earlier statement. When discussing how the CO knows when a phone goes off-hook, you learned that the tip and ring circuit is open when the phone is on-hook. That leads to the question, “If the tip and ring circuit is open, how can ringing current flow through this open circuit?” Actually, the circuit is considered open to DC. However, the phone’s internal circuitry has an electrical component called a capacitor between the tip and ring wires, and even though direct current does not flow through a capacitor, AC

Ringing, Dial Tone, and Other Bells and Whistles 15

does. Ringing voltage uses AC. Therefore, this ringing current can flow through a phone in the on-hook condition, causing the ringer to ring, as shown in Figure 1-5.
Figure 1-5
Tip

Ringing Circuit

Ringing Current

Capacitor Ringer

Hook Switch

Ring

Address Signaling
Address signaling allows a phone to specify the “address” (phone number) of the destination phone by dialing digits. Most phones support two types of dialing. The older method, used by rotary phones, is pulse dialing. Pulse dialing opens and closes the tip and ring circuit very rapidly. This series of open and closed circuit conditions within specific timing parameters indicates a dialed digit to the telephone switch, as shown in Figure 1-6.
Figure 1-6 Pulse Dialing
Caller Takes Telephone Off-Hook

Tip and Ring Circuit Closed (i.e, Make)

Tip and Ring Circuit Open (i.e., Break)

Telephone On-Hook

Caller Dials a “3” (Creating Rapid On-hook/Off-hook Conditions with a 60/40 Break/Make Ratio)

16

Chapter 1: Touring the History Museum of Telephony

When a phone’s handset is lifted off its cradle, the hook switch closes the tip and ring circuit. Similarly, when a phone’s handset is placed back on its cradle, the hook switch opens the tip and ring circuit. In fact, as a child, I tried dialing phone numbers by rapidly tapping the hook switch, attempting to simulate pulse dialing. Admittedly, my timing wasn’t perfect, and I didn’t always dial the correct number, but I dialed someone! A more efficient approach to address signaling is dual tone multifrequency (DTMF), also known as “touch tone” dialing. With DTMF, two simultaneous frequencies are generated, and a phone switch interprets this combination of frequencies as a dialed digit. For example, the combination of a 697 Hz tone and a 1209 Hz tone indicates a dialed digit of 1, as shown in Table 1-1. You might be curious as to why “dual” tones are used instead of just a single tone; the answer is background noise. The phone company doesn’t want the radio or your kids playing in the background to make a sound that may be interpreted as a dialed digit. So, specific combinations of two simultaneous frequencies are used to represent a dialed digit.
Table 1-1 Dual Tone Multifrequency (DTMF) Frequencies
Frequency 1209 Hz 1336 Hz 1477 Hz

697 Hz 770 Hz 852 Hz 941 Hz

1 4 7 *

2 5 8 0

3 6 9 #

Although pulse dialing served callers well for decades, DTMF dialing offers some significant advantages. Foremost of these advantages is speed. If you remember using an old rotary phone years ago (or even more recently—my mother still has one), think about how long it took to dial a 0. You positioned your finger in the 0 position, made a clockwise motion to dial the digit, and released the dial. The dial then very slowly rotated counter-clockwise back to its original position. Due to the mechanical inertia built into those rotary phones, it took a full second to dial that 0. DTMF enables you to dial digits much more rapidly. If your fingers are nimble enough, you can dial several digits in a second. The tones generated by a

Ringing, Dial Tone, and Other Bells and Whistles 17

DTMF keypad also enable a caller to interact with devices on the other side of the link. For example, suppose that you are away from home, and you want to check your messages, either on your home answering machine or on your voice mail. You dial your home number and then enter a series of DTMF tones to retrieve your messages. You would not be able to do that using pulse dialing.

Information Signaling
Similar to DTMF, information signaling uses combinations of frequencies, in this case to indicate the status of a call (that is, to provide information to the caller). For example, a busy signal is a combination of a 480-Hz tone and a 620-Hz tone, with on/off times of .5 sec/.5 sec. Another type of information signaling that you are probably familiar with is ring back. Ring back is the ringing sound heard by the caller to indicate that the dialed phone is ringing. Realize, however, that the ring back heard by the caller doesn’t occur at exactly the same time as the ringing on the destination phone. Try it. The next time you call someone, ask them how many times their phone rang before they picked up. Compare that number with the number of times you heard ring back. In some instances, the numbers will differ. Table 1-2 lists several other types of information signaling used in North America that you might be familiar with, along with the corresponding frequencies used for each signal.
Table 1-2 Information Signaling
Information Signal Description Frequencies (Hz)

Dial tone Ring back Busy signal

Heard by the caller after picking up the telephone handset Heard by the caller, indicating that the called phone is ringing Heard by the caller, indicating that the called phone is offhook Heard by the caller, indicating that the call cannot be completed successfully—perhaps due to all trunks being busy

350 and 440 440 and 480 480 and 620

Reorder tone

480 and 620

18

Chapter 1: Touring the History Museum of Telephony

A set of rules that determines how information is exchanged is called a protocol. You can think of a protocol as a “language of love” between two devices. The protocol that runs over the Internet, as you might guess, is called the Internet Protocol (IP). For decades, IP has transmitted data, not just across the public Internet, but also across private networks. Because voice can be digitized (converted to binary 1s and 0s), as described in Chapter 2, binary digits representing the voice can be transmitted across existing IP-based data networks. The process of sending voice traffic across an IP network is called Voice over IP (VoIP). As Figure 1-7 illustrates, a VoIP network has its own pieces and parts, just as a traditional telephony network does.
Figure 1-7 VoIP Components
PSTN PBX IP Phone IP WAN V Ethernet Switch V Gateway/ Gatekeeper V Gateway

Call Agent

MCU

Analog Phone

The list that follows defines the VoIP network components illustrated in Figure 1-7:


IP phones—Have an Ethernet network connection used to send and receive voice calls. Call agents—Replace many of the features previously provided by PBXs. For example, a call agent can be configured with rules that determine how calls are forwarded. The Cisco CallManager (CCM) product is an example of a call agent.



Ringing, Dial Tone, and Other Bells and Whistles 19



Gateways—Can forward calls between different types of networks. For example, you could place a call from an IP phone in your office, through a gateway to the PSTN, to call your home. Gatekeepers—Can be thought of as the traffic cops of the wide-area network (WAN). For example, because bandwidth on a WAN is typically somewhat limited, a gatekeeper can monitor the available bandwidth on the WAN. Then, when there is not enough bandwidth to support another voice call, the gatekeeper can deny future call attempts. Multipoint Control Units (MCUs)—Are useful for conference calling. On a conference call, multiple people can be talking at the same time, and everyone on that conference call can hear them. It takes processing power to mix these audio streams together. MCUs provide that processing power. MCUs may contain digital signal processors (DSPs), which are dedicated pieces of computer circuitry that can mix those audio streams together. Voice-enabled Ethernet switches—Add quality of service features to traditional Ethernet switches, allowing voice packets to be stored in a separate area from data packets. Voice-enabled Ethernet switches can recognize an attached IP phone, provide the attached IP phone with subnet information, and optionally supply power to the IP phone. note
The term Ethernet switch should not be confused with the term phone switch, discussed earlier in this chapter. Ethernet switches forward data, whereas phone switches forward phone calls.







With the maturity of PBX-centric phone systems, why might you consider migrating your existing tried and true PBX to a VoIP network? One of the first responses that comes to most people’s minds is cost, and that is certainly a valid reason. Actually, you can achieve cost savings from more than one source. Perhaps your company’s headquarters has a PBX, and that PBX connects to other PBXs or key systems at remote office locations. You might be paying a recurring monthly cost for the circuits interconnecting these privately owned phone switches. In addition to the circuits you have for your voice traffic, you might also have separate

20

Chapter 1: Touring the History Museum of Telephony

circuits for your data traffic between these offices. With VoIP, you could potentially eliminate the voice circuits, along with their monthly charges, and send your voice and data traffic over a single circuit. As an example, consider the university where I used to work. We had a PBX at the main campus, and a key system at each of three remote campuses. These remote campuses were small, just some office space in strip malls located in surrounding communities. In fact, each remote campus only had about four telephones each. Still, we had a dedicated T1 circuit from the main campus’s PBX to each of the three remote campuses’ key systems. There were also separate T1 circuits connecting the main campus’s data network to the data network at each remote campus. With a VoIP solution, the university could send both voice and data traffic over the existing data T1 circuits and eliminate the dedicated voice T1s. note
A T1 is a digital circuit that sends traffic at a rate of 1.544 Mbps. T1s are often used to carry voice, video, or data traffic. A T1 circuit can be subdivided into 24 separate channels, and PBXs require a full channel to support a voice path. Not all 24 channels need to be used for a single application (for example, voice, video, or data), however. A T1 can connect into a channel bank, which is a device that takes a T1 connection and breaks it out into 24 separate connections. If a full T1 is not required for a connection, many service providers sell fractional T1s, which provide a specific number of channels (less than 24).

Another cost savings offered by VoIP technologies can come in the form of cable plant expenses. Consider a company with separate infrastructures (that is, fiber optic cabling) for the voice, data, and video networks, as illustrated in Figure 1-8. With the high-speed data networking technologies available in today’s campus environment, voice, data, and even video traffic can peacefully coexist on the same high-speed network, as shown in Figure 1-9. This converged network approach requires less hardware because multiple traffic types use the same hardware.

Ringing, Dial Tone, and Other Bells and Whistles 21

Figure 1-8
PBX

Voice/Video/Data Before Convergence
PSTN PBX

IP WAN

Site A

Site B

Figure 1-9

Voice/Video/Data After Convergence

PBX PBX

PSTN

PBX

IP WAN

Site A

Site B

At this point, you can see that cost savings can be a major driving force in the migration to a VoIP network, and rightfully so. However, adopting a converged networking approach offers a number of other advantages. For example, a VoIP network not only mirrors the features offered by a PBX, but also offers a suite of new features.

22

Chapter 1: Touring the History Museum of Telephony

Later chapters in this book describe many of these features, such as the ability to support converged messaging (that is, having a single repository for voice mail, fax messages, and e-mail), virtual call centers, and extension mobility (that is, the ability for a user to log into a phone and receive their personal telephone settings). You can even play video games on many of the Cisco IP Phones, although that’s not one of the reasons you want to give management. To be fair, however, consider a couple of common concerns that many people have with the idea of VoIP. One of the biggest concerns that often surfaces is the reliability of a VoIP telephony system. After all, PBXs have a reputation for being up and operational most of the time. In fact, many people in the PBX industry boast about the five nines of reliability that they enjoy with their PBX. The five nines of reliability means their PBX is up 99.999 percent of the time. If you considered that level of reliability over the period of a year, that would only be five minutes of downtime during the entire year! This is a measure of reliability not just during working hours, but rather 24 hours a day, 7 days a week, 365 days a year (and 366 in leap year!) of uptime. Sad to say, many corporate decision makers have a dimmer view of network reliability. note
I experienced this skepticism personally. While working at a university, I approached my director and suggested that we might want to start considering the adoption of VoIP. My director became quite upset, pointing out that the PBX system “never” went down, whereas I was “always” doing something to the data network, bringing it to its knees. Many in management share this sentiment, and although it might have had some validity at one time, today’s VoIP networks can offer comparable levels of reliability to PBXs, as you will learn in Chapter 3.

Another major concern is the quality of the voice calls. Most people have experienced a poor cell phone connection, and many fear a VoIP call might offer a similar level of quality. Voice quality is so critical, this book dedicates an entire chapter (Chapter 6, “Why Quality Matters”) to addressing the variety of tools available to VoIP network designers to help them achieve fantastic voice quality.

Case Study: Your Turn to Put the Pieces in Place 23

These tools fall under a technology called quality of service (QoS). So, while there are definite concerns with VoIP, these concerns can certainly be addressed through proper VoIP network design, and later chapters explore many of these design best practices. As discussed in this section, a VoIP network can help businesses today literally do more with less, enjoying more features and more flexibility with less recurring cost. Even though you haven’t yet learned all the specific components that interconnect to form a VoIP network, you do have enough information at this point to start making some fundamental design decisions for a voice network. The next section puts your knowledge to the test.

Case Study: Your Turn to Put the Pieces in Place
To help you get a better feel for voice network design, consider a sample highlevel design scenario. A suggested solution is provided after the scenario. However, remember, when it comes to the design of a voice network, there is no one solution. The flexibility of voice technology allows many different design approaches to achieve the same goal. So, don’t be concerned if your solution differs from the suggested solution. Consider the following scenario: The XYZ Company comes to you wanting your advice for designing a telephone network to interconnect the XYZ Company headquarters with two of its remote offices. Even though the XYZ Company already has a data network interconnecting these offices, at this point, it isn’t completely convinced it should pursue a VoIP telephony network, as opposed to a traditional PBX/key system network. Therefore, you are asked to recommend a traditional telephony (PBX or key system) solution based on the criteria outlined in Table 1-3.

24

Chapter 1: Touring the History Museum of Telephony

Table 1-3

XYZ Company Requirements for a Telephony System
Location Number of Telephones Required Features

Headquarters

4500

Voice mail A conference bridge capable of supporting a conference of 20 simultaneous participants Access to the corporate voice mail system Access to the corporate conference bridge Capability to support 72 simultaneous voice paths back to the headquarters Access to the corporate voice mail system Access to the corporate conference bridge Capability to support 12 simultaneous voice paths back to the headquarters

Remote Office 1

2000

Remote Office 2

30

Because you are such an advocate of VoIP technologies, as opposed to a traditional PBX/key system approach, the XYZ Company asks you to add to your traditional telephony design your arguments as to why a VoIP network would be preferable. Use the space provided to diagram and document your design. Also, write a paragraph describing why a VoIP network might be preferable.

Case Study: Your Turn to Put the Pieces in Place 25

Design Diagram for XYZ Company:

26

Chapter 1: Touring the History Museum of Telephony

Design Description for XYZ Company:

Case Study: Your Turn to Put the Pieces in Place 27

Rationale for a VoIP Solution:

28

Chapter 1: Touring the History Museum of Telephony

Suggested Solution
Figure 1-10 illustrates a suggested solution for the case study. Remember, however, there isn’t just a single solution to voice network designs. Don’t be concerned if your design doesn’t exactly match the suggested solution. Rather, read through the suggested solution to see whether it triggers any ideas you might be able to use to tweak your design.

Design Diagram for XYZ Company
Figure 1-10 XYZ Company Suggested Solution

PBX
3 T1s

PBX

2000 Phones 4500 Phones
PBX Features: — Conference Bridge (20 Simultaneous Participants) — Voice Mail

XYZ Remote Office 1
Fr ac

tio

na

Key System
lT 1

XYZ Headquarters 30 Phones XYZ Remote Office 2

Design Description for XYZ Company Due to the number of phones located at the company headquarters (4500), the headquarters requires a PBX. When selecting a PBX, prospective vendors need to specify the extra hardware and software required to support the stated conference bridge and voice mail requirements. Remote Office 1 also requires a PBX because this site contains 2000 phones. Separate voice mail and conference systems are not required for this remote office,

Chapter Summary 29

however. This remote office can simply access the voice mail and conferencing resources located at the company headquarters. Because the trunks connecting the remote office PBX to the headquarters PBX need to support 72 simultaneous voice paths, three T1 circuits will be used to interconnect these two PBXs (that is, 24 channels per T1 * 3 = 72 channels). Remote Office 2 only requires a key system due to its relatively small number of phones (30 phones). Like Remote Office 1, there is no need for Remote Office 2 to have its own voice mail and conferencing systems. Remote Office 2 can access the resources that reside at the company headquarters. Because only 12 simultaneous voice paths are required between Remote Office 2 and the headquarters, a full T1 is not required. Instead, a fractional T1, containing 12 voice channels, will be used to interconnect Remote Office 2 to the company headquarters.

Rationale for a VoIP Solution A VoIP solution might be able to use the existing data network to simultaneously send voice and data traffic, thus eliminating the need for the three T1s and one fractional T1 specified in the design, which saves on recurring monthly expenses. A VoIP network would also lay the foundation for enhanced services. For example, instead of simply having a voice mail system, the XYZ Company may be able to use a product such as Cisco Unity (described in Chapter 7, “VoIP Supporting Roles”), which provides unified messaging. Unified messaging is more than just voice mail. It provides a single repository for voice mail, e-mail, and fax messages.

Chapter Summary
This chapter reviewed the history and operation of legacy telephony systems. Various flavors of telephone switches were discussed, including CO switches (which make up the PSTN), PBXs, and key systems. Both PBXs and key systems are privately owned telephone switches. Larger businesses use PBXs to support

30

Chapter 1: Touring the History Museum of Telephony

anywhere from 20 to 20,000 phones. Smaller businesses needing to support only 30 to 40 phones may opt for a key system. Placing an end-to-end phone call involves different types of signaling, including supervisor signaling (which indicates to the CO switch that a phone has gone offhook), information signaling (which provides information to the caller about the state of a call, such as a busy signal or ring back), and address signaling (which uses pulse dialing or DTMF dialing to communicate dialed digits to a telephone switch). You also learned that migrating from a traditional PBX-centric (or key systemcentric) telephony environment to a VoIP network offers several advantages. Cost savings is a primary motivator. Examples of these cost savings include reduced equipment and staffing expenses, in addition to the elimination of recurring monthly charges for dedicated voice circuits used to interconnect privately owned telephone switches. The advantages of VoIP, however, extend far beyond cost savings. A VoIP network lays the foundation for enhanced services that are not possible with legacy telephony solutions.

Chapter Review Questions
1. What are the names of the two wires used by a traditional home phone to

carry voice traffic and signaling information? (Select two.)
a. Ground b. Tip c. Magneto d. Ring 2. Who invented the first direct-dial telephone switch? a. Thomas Watson b. Almond Brown Strowger

Chapter Review Questions 31

c. Alexander Graham Bell d. Harry Nyquist 3. Which type of telephone switch is most appropriate for a business needing

to support 10,000 phones?
a. CO switch b. Key system c. PBX d. Ethernet switch 4. Identify three types of signaling used on PSTN networks. a. Information b. Address c. Fallback d. Supervisory 5. How many voice channels can be carried over a T1 circuit in a traditional

PSTN/PBX environment?
a. 16 b. 24 c. 30 d. 64 6. “Dial tone” is an example of which type of signaling? a. Information b. Address c. Fallback d. Supervisory

32

Chapter 1: Touring the History Museum of Telephony

7. Which of the following are potential advantages of a VoIP network? (Select

three.)
a. Reduced dedicated circuit costs b. More mature technology than PBX/key system approaches c. Lays a foundation for more advanced services d. Reduced physical plant costs 8. How much voltage does a telephone switch apply across the tip and ring

wires?
a. -48 volts of DC b. -48 volts of AC c. +90 volts of DC d. +90 volts of AC 9. Which VoIP component is used to forward calls between different types of

networks?
a. Call agent b. Gatekeeper c. Gateway d. MCU 10. Which VoIP component is used to mix multiple audio streams? a. Call agent b. Gateway c. Gatekeeper d. MCU

Sponsor Documents

Or use your account on DocShare.tips

Hide

Forgot your password?

Or register your new account on DocShare.tips

Hide

Lost your password? Please enter your email address. You will receive a link to create a new password.

Back to log-in

Close