Woodland Slope

Published on January 2017 | Categories: Documents | Downloads: 54 | Comments: 0 | Views: 481
of 21
Download PDF   Embed   Report

Comments

Content

Designing Woodland Roads
E C 1137 • Revised Jun e 2012
Steve Bowers

A

re you, as a woodland owner, expected
to perform certain engineering functions
typically performed by engineers when they
design roads? The answer is, “Sort of.” This publication does not pretend to turn you into a professional
engineer, but it does provide a basis for understanding the process of designing woodland roads. Your
intimate knowledge of your property enables you to
contribute special expertise to road design, such as
in planning the route and locating control points.
Understanding the process of designing roads helps
you identify whether you need professional services
and prepares you to supervise any contractors you
may hire.

Before doing any on-the-ground reconnaissance,
inspect aerial photographs, maps, soil survey
information, or even a simple sketch of your
property to identify a possible route location. These
activities help ensure the proposed road fits the
overall plan for providing access to the property.
Regardless of the size and scope of the road design, it
must fit the overall plan.

Control points
A major reconnaissance activity is to locate
control points for the road. Control points are
special areas on your property where it’s either
desirable to build or wise to avoid building a road.
The following are control points that deserve careful
consideration:

Designing woodland roads involves two elements:
developing the specifications for constructing the
road, and setting the field layout and location that
guide the construction. The degree to which you
become involved in road design depends on your
interest and background, and the complexity of the
task. Some woodland owners design and build their
own roads when the project is small-scale with a
simple design.

• Landings. Potential landing areas are locations
along the route where logs removed from a
harvest unit are loaded onto trucks. In cable
logging, this is the location of the yarding
machine. With ground-based logging, logs are
skidded to a landing location that minimizes
the skidding distances.

You can reduce the cost of road construction
through effective design. The cost of road design,
even when done by contracted professionals, is small
in relation to the cost of construction.

Contents

Reconnaissance
Road reconnaissance involves observing your
property with a road plan in mind. You know your
property as well as anyone and, with some training,
you can identify where roads should or should not
be built.



Reconnaissance . . . . . . . . . . . . . . . . . . . .1



Road geometry . . . . . . . . . . . . . . . . . . . . 4



Design specifications . . . . . . . . . . . . . . . . .7



Road structures . . . . . . . . . . . . . . . . . . . 11



Drainage planning . . . . . . . . . . . . . . . . . 12



Field location and layout . . . . . . . . . . . . . 14



Summary . . . . . . . . . . . . . . . . . . . . . . . 21



For more information . . . . . . . . . . . . . . . . 21

Revised by Steve Bowers, Extension forestry agent, Oregon
State University. Original author: John J. Garland, Extension
timber harvesting specialist emeritus, Oregon State University.
1

• Saddles. Ridgetop roads almost always pass
through saddles (low points along the top of a
ridge). When roads are located in saddles, you
have access to both sides of the ridge system.
This makes saddles good landing sites.

• Benches. Benches are natural breaks between
slopes where easy road construction and good
landing locations often are available. These
locations should be used whenever possible.

Weathered
bedrock,
soil, etc.

Bedrock

Debris avalanche

Alluvium

s

mp

Slu

Stream channel
w
flo

rth

Ea

g
Sa

Zone of
weathered
bedrock and
soil

nd

po

Bedrock

Slip surface
Toe

Tension cracks

Figure 1. Indicators of slides and slumps
Top: Debris avalanches and flows typically occur on steep slopes with shallow soils overlying an
impermeable layer. Indicators include areas of previous slides; steep areas lacking vegetation; and
granular, low‑cohesion soils that have a low to moderate clay content.
Bottom: Slumps and earthflows frequently occur together, creating such landform features
as sag ponds, tension cracks, and headwall scarps. Indicators include tipped, jackstrawed, or
pistol‑butt‑shaped trees; poor drainage in deep, clay‑rich soils; hummocky topography; and areas of
past failures.
2

• Steep hillsides and rock
outcrops. Generally, it is
difficult and expensive to construct roads on steep hillsides
with rock outcrops. However,
excavating a road through an
outcrop can be beneficial when
the outcrop provides surfacing
material.
• Slumps and slides. Roads on
unstable terrain are difficult to
deal with during construction
and can lead to more extensive
problems with slope stability.
Indicators of slumps and slide
areas are listed in Figures 1
(page 2) and 2.

Before failure

Original ground surface

Potential failure
surface

After failure

• Wet spots, swamps, and
springs. If possible, avoid
road locations that expose
subsurface water or that cross
wetlands. These areas present
future maintenance problems.

Original ground surface

Ground surface after slump

Failure surface
• Potential stream crossings.
Suitable locations for stream
crossings depend on the type
of crossing and the ease of
Figure 2. The effects of improper road location on a slump area
constructing it. A ford requires
a shallow streambed with a
solid bottom, whereas a bridge
These are lines of ribbons hung in trees and shrubs
requires a narrow channel with
at the approximate location of the road. In simple
stable stream banks. You should consult with
situations, you can build roads from these ribbon
your Oregon Department of Forestry (ODF)
lines. For more complex situations, however, the
stewardship forester when confronted with
trial location provides a rough guide for collecting
springs and stream crossings.
detailed information to use in calculating the
• Sharp ridges and “V” draws. Construction
road’s final design. Trial locations may be subject to
problems are likely to occur when sharp
revisions and modifications, even after you begin
ridges require heavy excavation to create a
construction. If you encounter problems (e.g.,
stable roadbed. Crossing V shaped draws also
hidden rock), it’s far better to revise the road location
can cause problems if the excavated material
than incur high costs of drilling and excavating these
becomes unstable and slides away underneath
rock sites or initiate environmental problems.
the roadway.
The major reason for conducting a thorough
• Areas for surplus excavation. In addition
reconnaissance is to minimize construction cost
to other control points, it’s useful to identify
by implementing designs that avoid environmental
benches or other stable, flat areas where you
problems. For example, roads that are too close to
can dump excess excavation.
streams may trigger land failures; such failures are
The next step in road reconnaissance is to connect
the result of a poor reconnaissance effort. Once you
the desirable control points with trial ribbon lines.
establish a trial location, it can be helpful to contact

3

the ODF forest practices forester for advice on
environmental questions and requirements of the
Oregon Forest Practices Act.

road sections when it’s impractical to maintain a
ditch. Build cross-drains for inslope roads using
rolling dips or rubber water bars (see Figures 4, page
5, and 18, page 14) so that the entire surface of the
road handles the rainfall.

Road geometry

On roads with steep grades—10 to 15 percent—
the inslope must be 1 to 3 percent higher than the
travel grade, or the water will drain down the road
surface rather than to the inside. Inslope roads on
steep grades may present traction problems when
combined with the slope across the surface. Inslope
roads are more effective on gentle grades.

You can build roads in a variety of shapes. Their
surface shapes and characteristics depend on
management objectives and the terrain. Figures 3, 4,
and 5 show some road shapes.

Crowned roads
Roads with the center elevated to drain water off
half the road to the outside and half the road to an
inside ditch are called crowned roads (Figure 3). The
slope of the crown needs to be sufficient to quickly
drain water off the road or to the ditchline. This
design is the most common road surface because
the running surface, if properly maintained, quickly
drains water off the road.

In inslope roads, the spacing of cross drains needs
to be close enough to handle the runoff, but not
so close that they create issues with erosion on the
downside of the road. They must be large enough to
direct water across the road to the outside, but not so
large that they present obstacles to vehicles.

Outslope roads

In crowned roads, a system of ditches and crossdrains maintains the greatest degree of control
over the water. Cross-drains should be spaced at a
frequency that minimizes erosion of the ditch and
adequately handles water during periods of frequent
and intense rains. Proper maintenance of the road
surface, ditches, and cross-drains is critical to their
effectiveness.

Roads that drain water to the outside across
their entire surface are called outslope roads (see
Figure 5, page 5). Because water is not collected
and controlled, the outslope grade across the road
must be sufficient to keep the runoff draining to
the outside. It is imperative you maintain the road
surface because no cross drains are available.
Ridgetops with gentle grades are good candidates
for outslope roads. These roads, if maintained
before snowfall, may be more effective in snow
areas because they can handle the snowmelt. On
steep grades, outslope roads have the same kinds of
traction problems as inslope roads.

Inslope roads
Roads that have a slope across the running
surface toward the cutbank and do not have a
constructed ditch are called inslope roads. Use these

Ditch width 3'

Surface width 12'

Sustained flow of water
should not be higher than
bottom of rock layer

Centerline
3%

3%
Rock
Subgrade

Figure 3. Crowned road cross-section
4

Surface width 12'

Centerline

3%

Rolling dip feature

Inslope

Water flow

1'–2' drop
Inslope

20'

40'

Figure 4. Inslope road cross-section
Surface width 12'

Centerline

3% surface
cross-section slope for drainage

Figure 5. Outslope road cross-section

5

Full-bench roads and balanced
roads

Excavation = all volume removed from site

Depending on terrain conditions,
woodland roads are mixtures of cutand-fill construction (see Figures 6,
7, 8, and 9, page 7). You can excavate
the road surface from undisturbed,
stable soil or build it entirely from fill
material.
Full-bench roads are usually built
on slopes over 65 percent. The entire
running surface is on previously
undisturbed (and presumably stable)
soil.
You can transport the excavated
material to an area needing fill
material or to a disposal (waste)
area. If the amounts of excavated
material are small, relative to the
total excavated material, you can
sidecast the material along the edge
of the road. However, if this practice
is abused, landslides and sidecast
failures can result, making large
land areas unproductive and causing
possible environmental issues if the
road is adjacent to nearby streams.
A common practice on gentle
slopes is to build part of the roadway
on a stable bench and use the
excavated material to build a portion
of the running surface. You can
do this by removing all debris and
woody material from the side slopes
and depositing the clean fill material
to minimize road failures.
It is possible to calculate the
amount of fill material needed and
excavate only the amount for a road
cross-section (see Figure 8). Include
an allowance for shrinkage that
provides additional material.
When the excavated material
matches the required fill, the crosssection is balanced. On gentle slopes,
balanced sections minimize the
amount of earthwork excavation and
materials handling.

Original ground

Excavated volume
removed

Undisturbed soil

Centerline

Figure 6. Full-bench road cross-section

Excavation = partial volume removed + partial volume for fill

Excavated

Centerline

Fill
Original ground
line
Remove vegetation and debris from
original surface (potential slippage zone)

Figure 7. Road cross-section with partial fill

Excavation = fill needed + amount to compensate for fill shrinkage
Centerline
Excavated

Fill

Figure 8. Balanced road cross-section on gentle slope

6

Section

Sec

n

tio

Cut slope

Cut slope

Exploded cross-section views

Culvert

Centerline

Compact soil in
12" layers

Extra excavation
needed for fill
material

Centerline

Figure 9. Fill cross-section with extra excavation for fill material

Balanced excavation also describes the length
of road where excavated materials must be
accumulated for a fill section (see Figure 9). Road
design procedures estimate the excess excavation
needed on both sides of a fill section to provide
material for the fill.

on the size of the job, specifications (or “specs,” as
they sometimes are called) can be a simple list or
pages of contract provisions. The most common
specifications are discussed here, along with criteria
for deciding which are needed for woodland
properties.

The extra excavation depends on the amount of
shrinkage. Also, fill sections often are compacted in
layers to develop road strength; thus, the amount
of excavation also depends on the degree of
compaction of the fill.

Road width
Most landowners want roads as narrow as
possible to minimize the cost of construction and
the amount of land area removed from production.
A 12-foot running surface is usually needed for
log truck traffic. If you plan to gravel the road, the
subgrade (width of the roadway including ditch)
should be at least 14 feet. Curves and two-way traffic

Design specifications
Contractors and landowners who build their
own roads need design specifications. Depending
7

50

' ra

Alignment

di

us

50

Some large mechanized logging
equipment requires a minimum
running surface of 14 feet (16-foot
subgrade). Also, if you plan to use the
road as a landing area, you may need
wider sections to allow traffic to pass.
Designate landings in advance and
widen them during road construction.

' ra
di
us

may require widening the road surface
in designated segments.

Alignment is the degree of
curvature in the road. Roads should
be as straight as possible; however,
there are always tradeoffs. If road
construction is made easier by
Figure 10. Log truck on a curve with a 50‑foot radius
adjusting alignment to fit the terrain,
the road will have curves. However,
there are limits on how sharp the
Grades
curves can be and still allow log truck traffic.
The slope (grade) of roads is either adverse or
Measure curves by the radius of curvature. A
favorable. Favorable grades are downhill slopes for
minimum radius of 50 feet is needed for log trucks
loaded trucks and adverse grades are uphill slopes
(see Figure 10). Another way to measure curves
for loaded trucks.
is by using the middle-ordinate method, which
Favorable grades may reach 12 to 15 percent for
requires you make measurements in the middle of
short
distances, while grades of less than 10 percent
the roadway rather than from the center of the circle
are
recommended
for adverse grades. For most
(see Figure 24, page 19).
road designs, steeper grades are possible under
Although you can calculate limits of curvature
special circumstances, such as terrain conditions
during design, the real test is whether a log truck can
where construction and excavation costs become
pass the curves. If you plan to harvest poles or utilize
prohibitive. Sharp curves require moderate grades,
chip trucks on the property, the curves will need to
not greater than 7 percent.
accommodate the added vehicle length.
If two grades join on the road, you will need a
Curves in draws or around ridges or switchbacks
vertical curve to smooth the transition (Figure 12,
(horseshoe turns) on a slope are especially critical.
page 10). Failure to plan for these transitions can
You can improve these trouble spots by curve
result in truck bind, caused by the limited vertical
widening, in other words, providing extra road
movement of loaded trucks.
width at critical points along the curve to allow
Intersections also are areas where grades are
longer trucks (such as those carrying poles) or
critical.
In a location where one road leaves another,
logging equipment to pass (see Figure 11, page 9).
you must continue with the original grade for at least
Road intersections are another element of
100 feet to make a smooth transition. If the traffic
alignment. Design intersections so that loaded
must stop or slow down at an intersection, make the
trucks can make the turn easily. The State Highway
favorable grade low so the vehicle can come to a stop
Division district engineer must approve intersections
and make the adverse grade low so the vehicle can
with public highways. Other considerations include
start out again.
sight distance (clear field of vision for oncoming
Landing grades must be just steep enough to
traffic), distance to other intersections, and
drain off water. When loaded log trucks leave the
intersection width.
8

Cut slope
Curve widening
Cut slope
Extra excavation or extra fill

ius

d
' ra
80

ill

m
To

Figure 11. Curve widening to permit truck passage on sharp curves

landing, the grade must be low enough to get them
started.

Excavation
Because most forest road construction consists of
excavation, the road design must specify how much
earth to remove at the centerline of the road and
how steep to make the cut slope and fill slopes.

On gentle terrain, road grades may alternate from
2 to 3 percent (where conditions are favorable or
adverse) without affecting truck efficiency. Rolling
grades (alternate segments of favorable and adverse
grades) can help drainage because water velocity
does not build up before it drains across the road.
On inslope and outslope roads, rolling grades are
essential for controlling surface runoff.

You measure cut slopes opposite the way you
measure grades (Figure 13, page 11). For a ½:1 cut
slope, the elevation difference is one vertical unit for
every ½ unit of horizontal distance.
Cut slopes are designed to match the soil type’s
ability to hold the slope’s steepness. Steep hillside
slopes of hardpan soils that are high in clay can hold
a ¾:1 cut slope, while gentle slopes with loose, noncohesive soils need a 1:1 cut slope. (Rock can be cut
vertically.)

Clearing limits
Clearing limits, or right-of-ways, are well-defined
areas to be logged before road construction. These
areas vary in width and extend about 5 feet beyond
the edge of cut slopes or fills. A 30-foot clearing limit
is considered a minimum width. Remove vegetation
from between the clearing limits and dispose of it
outside the roadway, or pile and burn it. Dig stumps
out instead of leaving them to rot in the road.

On some steep slopes, a 1:1 cut slope may not be
as steep as the adjacent ground slope. However, the
cut slope will fail if it is too steep for the soil to hold
(Figure 14, page 12).

9

D = 2.5'
e)

rs
ve

=
g 1)
e(

%

–8

(ad

Ro

ad

ad
Gr

R

d
oa

sur

fac
e

Gr
ad

e(

g
2

e
ac
urf

)=

+1

2%

s

(fa
vo
ra
b

le

Length of vertical curve
L = 100' horizontal distance

)

To

g
1

=

m

ill

+1

2%

(fa
vo
ra
b

le

)

Length of vertical curve
L = 100' horizontal distance

Sample amounts of excavation
differences needed for smooth
vertical curves
g2–g1

D






2.5 ft
1.9 ft
1.3 ft
0.6 ft

± 20%
± 15%
± 10%
± 5%

D=

(g2–g1) L

D = 1.1'

800
g2 = 3

% (fa
vorab
le

)

D = difference from grade intersection to form vertical curve
g1, g2 = grades in percent

To mil
l

Figure 12. Vertical curves

10

Vertical

D


Cut slopes


C
1
B
A

1

A

B
C
D

⁄4

1

⁄2

1

1
⁄4

3

1

Design
measurement

1:1
⁄4:1
1
⁄2:1
1
⁄4:1
3

1
Centerline

Figure 13. Cut slopes at common steepnesses

Wet spots are likely to cause problems. You may
use special fabrics or dig out the wet material and
replace it with rock or better material (e.g., replacing
blue clays with sandy soils).

Fill slopes also depend on terrain steepness and
soil types, but to a lesser degree than cut slopes. Fills
usually are designed to have a 1½:1 slope (Figure 15,
page 13) because this is the steepness that will hold
non-compacted or loose earth. The stability of fills
on sloped terrain depends on the original ground’s
steepness. Fills on slopes that are more than 65 percent
will not catch (attach to the original ground) or
provide support; material will ravel (slide away)
down the hillside (Figure 16, page 13).

Compaction benefits road subgrades, especially
fills. It is common to specify that fills be built up in
12 inch lifts (layers) and compacted each time by the
road-building machine. You may need compaction
machines if the fill is large or if the soil strength is
very low. Consider compacting the entire subgrade
if you have to surface the road immediately after
construction.

Specify where to dump excess excavation in your
road design. Waste areas need to be flat and stable.
Occasionally, material needed for a fill is unavailable
or of poor quality. To compensate, you can include
borrow pits (excavations outside the construction
area that provide soil and aggregate or both) in your
road design.

Road structures
You need specifications for all structures that you
build into forest roads. This includes bridges and
complicated support structures, as well as the oftenoverlooked culverts and earth-constructed items,
such as water bars and dips.

End hauling is the process of removing material
from its excavation site or transporting it to a fill area
with a dump truck. While the machines typically
used in road construction can move material
200 to 300 feet, it’s usually more economical to load
the material in dump trucks for hauling. Good road
design eliminates or minimizes end hauling.

Slope stabilization structures
Under special circumstances, woodland roads
may need to cross unstable slopes. You can use
structures such as bin walls, sheet piling, rock
buttresses, and half bridges, but they likely will
require professional assistance in planning and

Occasionally, you can anticipate road surface
problems and specify solutions in the road design.
11

Failed cut slope

Ori

⁄4:1

1

⁄4:1

3

1

gin
a

l gr
ou

nd

1
1

⁄4

3

slo

pe

⁄4

Centerline

Preferred cut slope

Figure 14. Cut slopes that are too steep may fail.

measures such as rock riprap (rocks used as armor),
culvert half rounds, and water discharged on stable
locations to prevent erosion and road undermining.
When installing pipe culverts, proper design may
eliminate poor-functioning crossings. (continued on
page 14)

constructing. Although these structures may cost
as much as a bridge, you should be aware that they
exist to solve particular slope stability problems, and
you should only consider them after exhausting all
other options.

Drainage planning

Table 1. Water bar spacing guide1

A road that is properly designed and constructed
to control water will avoid most maintenance
problems. Therefore, the key requirement of a good
plan is drainage, drainage, drainage! You will need to
design frequent cross drains and stream crossings to
control water during storms (Table 1).

Soil type
Road
grade
(%)

Cross drains
Several structures are available for draining water
across the road. These range from simple earthwork
structures like water bars and rolling dips to opentop, wooden culverts and pipe culverts of various
materials. Figures 18, 19, 20, and 21(pages 14-15)
illustrate these options.
When designing cross drain structures, consider
where the water will most effectively and efficiently
drain across the road. Use outfall protection

Granitic
or sandy
(ft)

Shale or
gravel
(ft)

Clay (ft)

2

900

1,000

1,000

4

600

1,000

800

6

500

1,000

600

8

400

900

500

10

300

800

400

12

200

700

400

15

150

500

300

20

150

300

200

25+

100

200

150

Distances are approximate only; vary them to take
advantage of natural features. From: Forest Road Design.
September 2006. Salem: Oregon Department of Forestry.

1

12

Original ground surface

Centerline

1
11⁄2

Centerline

1
1

2

2

Original ground surface

Figure 15. Partial fills at 11⁄2:1 (top) and 2:1 (bottom) fill slopes

Original ground surface

Centerline

1
11⁄2

When fill does not “catch” (attach to original
ground), it may slide away.

Figure 16. Fill slopes will not catch on steep slopes.
13

For example, a single larger pipe may be a
more effective culvert than several small pipes
combined (Figure 17).

12" pipe culvert
Area = 0.78 square feet

Stream crossings
You can use culverts made from steel,
aluminum, concrete, or plastic to cross small
streams. The size you need depends on local
conditions (i.e., rainfall, drainage area, the
stream’s fish-bearing status, etc.), but an
acceptable starting point is to have the area
of the culvert opening equal to the area of the
stream channel at the historical high water level.

12"

To construct a stream crossing, you need a
written plan and consultation with the Oregon
Department of Forestry (ODF) in accordance
with the rules of the Oregon Forest Practices
Act. A Stewardship Forester will assist you in
determining whether the stream is fish-bearing.
Note: the presence of fish does not determine
whether it is labeled a fish-bearing stream.
Do not attempt to install a culvert in a stream
without proper notification to officials!
In fish bearing streams, culvert design
must plan how fish will get into and out of the
culvert, as well as the maximum water velocity
in the culvert. Such determinations can only be
made with professional advice from the Oregon
Department of Forestry.

3 irrigation pipes used as culvert
Area = 0.59 square feet

6"

6"

6"

Note: Small, inexpensive pipes used as a culvert may carry less
water and plug with debris more easily than a larger single culvert.

Figure 17. A comparison of three pipes to a single culvert

Under some circumstances, you might
consider a design that uses pipe arches,
bridges, fords, or temporary crossings instead
of culverts. Less costly approaches may save
money in the short run, but their long-term
effectiveness, both environmentally and
economically, is the true measure of their
success.

5'

d
Roa

ace

surf

12"
12"

(Used on inactive roads)

Field location and layout
Ribbons, wooden stakes, and metal tags
guide the construction of the planned roadway.
While there is no single standard or marking
system, the information provided in this
publication is common to all road construction.
You have to mark the road in a way that
the machine operator can understand. If the
operator doesn’t understand the necessary
(continued on page 17)

45°

Figure 18. Water bar cross-section and placement (used on
inactive roads)
14

Rolling dip feature

Inslope

Water flow

1–2' drop
Inslope

20'

40'

Figure 19. Use a rolling dip to drain surface runoff.

4x4 running boards
Ensure upslope
is free of debris

8" diameter logs

6"
Ditch water flow
Ditch
plug

30°
30°
Ditch plug
to keep water
from bypassing
culvert
Culvert materials available
• Concrete
• Steel
• Aluminum
• Plastic
Riprap for
outfall protection

Riprap

Figure 20. Wooden or steel open-top culvert

Figure 21. Pipe culvert installation
15

16

520

540

560

le)

0

+4

1

12" culvert (0+70)

rab
avo
% (f

Intersection
with existing
road

100' vertical curve
(V.C.) D=0.5'
+8

2

3

12" culvert (2+50)

Figure 22. Road profile for construction

Elevation (ft)

4

Cut 9 5 at ridge

100' V.C. D=2.3'

le)

580

(
%

f
a
v
or
ab

0%

-1

5

6

100' V.C. D=2'

12" culvert (6+40)

7

Stations (100' horizontal distance)

)

se

dv
er

(a

Planned road surface

Existing ground profile

8

%

+6

9

)
ble

ra
vo
(fa

10

11

Fill 7 0
24" culvert
(11+00)

12

100' V.C. D=0.8'

13

12" culvert (12+30)

%
+8

le)
rab
o
v
(fa

le)
avorab
+2% (f

14

Landing

information, you or the contractor have to explain
it. You or the contractor must also monitor the
site and replace the construction stakes (and other
markers) that are damaged or destroyed during the
construction process. A careful pre-operation review
is essential, and construction supervision must be
frequent to avoid problems.

the same time the road reaches the planned grade
elevation.

Communicating operator information

You also can use profiles to obtain information
on stream crossings, culverts, road cross-drains,
and other vital elements of road construction. If a
profile is not available from engineering information,
a sketch—though less accurate—provides a written
form of communication.

The machine operator also needs to know how to
use the excavated material. A road profile showing
ground levels and proposed grades is very useful,
if available (Figure 22, page 16). The profile shows
where cut and fill sections are located along the road.

Establish the right-of-way or clearing limits with
ribbons, colored paper tags, or stakes.
Stake the centerline of the road—this is especially
critical on curves, switchbacks, and intersections.
The operator needs to know where to begin cutting
and the slope of the back cut. This information
is given on a slope stake, a stake marking the
point where the outer limit of a cut or fill meets
the original ground. When the operator has this
information, cutting or filling can begin at the slope
stake, and the proper road width will be achieved at

The construction crew can avoid future problems
with culverts and cross drains through proper
installation. Figures 18, 19, 20, and 21 (pages
14-15) are some examples that you can include
in specifications or use to communicate with the
construction crew.

ts
gen

n
d ta

Roa

End of curve

Desired location of
curve center
Angle
between
tangents

Select curve that goes
through desired location
of curve center

⁄2

1

⁄2

1

#3

#2
#1

Trial curve #2
Trial curve #1
Beginning of curve

ad

Ro

Compass for drawing curves

s
nt

e
ng

ta

Figure 23. Trial curves with the center of the curve located

17

Curves frequently connect two straight sections,
or tangents, of road. On gentle terrain you can
roughly stake these tangents in advance. The line
bisecting the angle between the tangents is the line
along which the curve will be centered (Figure 23,
page 17). When you select the place the road will
cross this bisecting line, you can locate the center of
(continued on page 20)

Curve layout on woodland roads
Two simple approaches to curve layout are
described here, and while they may be adequate
for many circumstances (including compound and
reverse curves), you may require more involved
techniques and professional assistance for complex
situations.

Table 2. Conversions of slope percentage readings and slope distance to vertical
and horizontal distances
Slope Distance (ft)
Slope
(%)
5

10'

15'

0.5*

0.7
10.0*

7

0.7

1.0

1.0
1.2

1.8

15

1.5

2.2
9.9

20

2.0

2.9

4.3

35

3.3

5.0

9.4
40

3.7

5.6
9.3

45

4.1

6.2

50

4.5

6.7
8.9

55

4.8

7.2

60

5.1

7.7
8.6

11.2

9.6

12.9

13.4

12.0

10.3

14.5

0.5
10.0

16.9

15.4
21.4

Horizontal
distance (ft)

18

21.7

44.7
24.1

39.4
23.2

34.3

45.6
22.4

40.2

35.0
20.6

30.0

20.5

20.1

19.5

46.4

41.0

35.8

30.7
18.0

25.7

18.5

17.9

47.2
18.6

41.8

36.5

31.3

26.3

*Read table cells as:
Vertical
distance (ft)

15.7

16.5

16.7

16.4

47.9

42.5

37.1

31.9

26.8

21.9
12.9

17.1

14.4

14.4

14.9

14.9

48.5

43.1

37.8

32.5

27.4

22.4

17.5

13.0

12.3

12.9

13.2

49.0
12.1

43.7

38.3

33.0

27.9

22.8

17.9

13.1

11.1

10.3

8.9

11.6

9.8

10.9

11.5

49.4

44.1

38.8

33.5

28.3

23.2

18.2

13.4

8.8

9.3

8.2

10.1

9.9

8.8

9.7

49.6
7.4

44.5

39.2

34.0

28.7

23.6

18.6

13.7

8.6

8.3

7.4

8.5

6.0

6.7

7.8

49.8

44.7

39.6

34.3

29.1

23.9

18.9

13.9

9.1

7.2

6.6

6.9

7.3

5.4

5.9

49.9
5.0

44.8

39.7

34.6

29.4

24.3

19.2

14.2

5.9

6.1

5.7

5.2

3.5

4.5

4.8

49.9

44.9

39.8

34.8

29.7

24.5

19.4

14.4

4.5

4.9

4.9

4.2

2.5

3.1

4.0

50'

44.9

39.9

34.8

29.8

24.7

19.6

14.6

9.6

3.7

3.9

3.6

3.6

2.2

2.8

3.5

45'

40.0

34.9

29.9

24.8

19.8

14.7

9.7

30

3.0

2.9

2.4

3.0

2.0

2.4

3.0

40'

35.0

29.9

24.9

19.9

14.8

9.8

25

2.4

1.7

2.1

2.5

35'

30.0

24.9

19.9

14.9

1.5

1.7

2.0

30'

25.0

20.0

14.9

9.9

1.2

1.4

1.5

25'

20.0

15.0

10.0

12

1.0
15.0

10.0

10

20'

43.8
25.7

38.6

42.9

End of curve
Tang
e

nt

Curve
radius
(ft)

157

Stick
length
(ft)
2



106

3



80

4



65

5



55

6

G

25'
E

F
Temporary stake
Stake on curve

'

25

Stick length

D
25

B

'

C
25'

Beginning of curve

A

Tan
g

ent

Figure 24. The middle‑ordinate curve‑location method
Follow the steps below to lay out a curve using the middle-ordinate (sticklength) method. Assign letters to the stakes you use for layout. Once a
curve fits a given location, mark the stations on the stakes starting from the
beginning of the curve (for example, if stake A = station 12+10, and stakes are
used every 25 feet, then stake C would be marked 12+35; stake E, 12+60; and
so forth). All distances are horizontal measurements (they are not on the slope).

4.

At E, measure a stick length toward the center of the curve and set
temporary stake F. From C, sight through F and measure off 25 feet from
F to set stake G on the curve.

5.

Repeat these steps until you approach the tangent for the end of the
curve.

6.

If the curve does not fit on the first trial, you have several options to fit
the curve.

1.

Select the desired radius curve and the corresponding stick length to use.

2.

From stake A, measure 25 feet to B, extending the tangent line at the
beginning of the curve. At right angles to the tangent, set stake C one
stick length from the tangent. You now have the first stake on the curve.

• Change the stick length (and thus the curve radius). A longer stick
makes a sharper curve; a shorter stick makes a curve of larger radius.

3.

At C, measure off the stick length toward the center of the curve and set
temporary stake D. From A, sight through D and measure off 25 feet from
D to set stake E (another stake on the curve).

• Try combinations of various starting points and stick lengths.

• Start the curve earlier than stake A or later (at B) to fit the topography.

19

+11%
ht
ye heig
ht to e
ig
e
h
e
Ey

Road

ade
subgr

Figure 25. Checking road grades

example, that the road is at the planned grade, curve
radii are being satisfied, and the centerline is in the
correct position.

the curve by trial and error. The correct radius curve
will just touch the centerline of each tangent and will
“curve” through the area you want the road to cross.
For practice, try this on paper with a compass.

Consider this example: your road is under
construction but is not yet ready to grade. You
can monitor progress using two approaches. First,
you can use a hand level to check the amount of
cutting (or filling) completed. Or second, you can
use a clinometer (a device for measuring slope) and
convert the percent reading, along with the slope
distance, to vertical and horizontal measurements.
(See Table 2, page 18, to convert slope readings and
slope distances to vertical and horizontal distances.)
Clinometers also give direct readings on road grades
between two points on the road (Figure 25). Critical
places to check are curves (especially vertical ones),
switchbacks, intersections, and steep segments.
Using either of these two methods, you then can
reestablish the centerline and leave a stake to tell
the operator how much more cutting (or filling) is
needed, in the event there are necessary adjustments
in the road design.

In the field, once you locate the center of the
curve, you can use two tapes or measured ropes
to find the stations along the curve. On more
difficult terrain, such as sharp draws, ridges, and
hillside switchbacks, it may be impossible to locate
the center of the curve. In these cases you can use
the middle-ordinate (stick length) layout system.
This system may be easier to use than locating the
center of the curve. Figure 24 (page 19) provides a
procedural approach; however, you should be aware
that several trials may be necessary to get the curve
to fit.
During the process of road construction, it’s
useful to restake the difficult curves after completing
the right-of-way logging. The machine operator
will then be able to construct curves at the proper,
designated locations.

Checking road construction

Monitoring road construction does not mean
rigid adherence to field-location guidelines; the road
construction process is not exact. Grades within ±1
percent and excavation to the nearest foot usually are
acceptable. The most important criterion is whether
the road will serve the intended function.

The time and effort you invest in careful road
design will be lost if your design is not reflected
in construction practices. Thus, it is essential to
check on road construction frequently to verify, for

20

Good construction can improve road design.
However, failing to construct portions of the
road within acceptable variances of the design
specifications and ignoring the field layout and
location markers can result in roads that are
problems for trucking and maintenance activities.

Other publications
Managing Woodland Roads: A Field Handbook
discusses the major aspects of woodland roads
relating to their design, inspection, maintenance,
and repair. (Oregon State University, 2006).

Summary
Road specifications and field layout and location
are the essence of road design. You may wish to
design simple and small scale road building projects
or seek out professional service for bigger, more
complex projects. The information provided in this
publication will help you design your own road or
supervise those providing contract services.

For more information
There are a number of other helpful publications
available on various topics related to the
management of a timber sale.

OSU Extension Service publications
• Contracts for Woodland Owners and Christmas
Tree Growers (EC 1192) describes how to
develop a contract and includes samples of
four types of agreements: timber sale, logging,
temporary road use, and road easement.
• Grass Seeding Forest Roads, Skid Trails, and
Landings in the Inland Northwest (PNW 628)
outlines strategies for establishing vegetation
to stabilize erodible areas along forest roads
and skid trails.

© 2012 Oregon State University. This publication was produced and distributed in furtherance of the Acts of Congress of May 8 and June 30, 1914. Extension
work is a cooperative program of Oregon State University, the U.S. Department of Agriculture, and Oregon counties. Oregon State University Extension
Service offers educational programs, activities, and materials without discrimination based on age, color, disability, gender identity or expression, marital
status, national origin, race, religion, sex, sexual orientation, or veteran’s status. Oregon State University Extension Service is an Equal Opportunity Employer.
Revised June 2012. Published July 1983.

21

Sponsor Documents

Or use your account on DocShare.tips

Hide

Forgot your password?

Or register your new account on DocShare.tips

Hide

Lost your password? Please enter your email address. You will receive a link to create a new password.

Back to log-in

Close